Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM2040EQ _58 Vehicle Interior _014727 SUPPLEMENTAL RESTRAINT SYSTEMS _0075078 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1627/82  Lost communication with Side Airbag Sensor LH  B1628/82  Side Airbag Sensor Assembly LH Initialization Incomplete  B1637/82  Lost Communication with Rear Airbag Sensor LH  B1638/82  Rear Airbag Sensor Assembly LH Initialization Incomplete  B1647/82  Lost Communication with Side Satellite Sensor Bus LH  


DESCRIPTION

The side collision sensor LH circuit (to determine deployment of the front seat airbag assembly LH and curtain shield airbag assembly LH) is composed of the airbag sensor assembly, side airbag sensor assembly LH and side No. 2 airbag sensor assembly LH.

The side airbag sensor assembly LH and side No. 2 airbag sensor assembly LH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbag should be deployed.

These DTCs are stored when a malfunction is detected in the side collision sensor LH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1627/82 Lost communication with Side Airbag Sensor LH
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor LH circuit.

·

Side airbag sensor assembly LH malfunction

·

Side No. 2 airbag sensor assembly LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Side airbag sensor assembly LH

·

Side No. 2 airbag sensor assembly LH

·

Airbag sensor assembly


Does not apply to test/check mode
B1628/82 Side Airbag Sensor Assembly LH Initialization Incomplete
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor LH circuit.

·

Side airbag sensor assembly LH malfunction

·

Side No. 2 airbag sensor assembly LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Side airbag sensor assembly LH

·

Side No. 2 airbag sensor assembly LH

·

Airbag sensor assembly


Does not apply to test/check mode
B1637/82 Lost Communication with Rear Airbag Sensor LH
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor LH circuit.

·

Side airbag sensor assembly LH malfunction

·

Side No. 2 airbag sensor assembly LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Side airbag sensor assembly LH

·

Side No. 2 airbag sensor assembly LH

·

Airbag sensor assembly


Does not apply to test/check mode
B1638/82 Rear Airbag Sensor Assembly LH Initialization Incomplete
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor LH circuit.

·

Side airbag sensor assembly LH malfunction

·

Side No. 2 airbag sensor assembly LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Side airbag sensor assembly LH

·

Side No. 2 airbag sensor assembly LH

·

Airbag sensor assembly


Does not apply to test/check mode
B1647/82 Lost Communication with Side Satellite Sensor Bus LH
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor LH circuit.

·

Side airbag sensor assembly LH malfunction

·

Side No. 2 airbag sensor assembly LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Side airbag sensor assembly LH

·

Side No. 2 airbag sensor assembly LH

·

Airbag sensor assembly


Does not apply to test/check mode

WIRING DIAGRAM

C239250E33
0.552,4.677 1.146,5.052 0.594,0.375 10 N8 0.552,4.854 1.823,5.51 1.271,0.656 10 Side Airbag Sensor Assembly LH 3.042,4.844 4.385,5.302 1.344,0.458 10 Side No. 2 Airbag Sensor Assembly LH 3.042,4.677 3.573,5.042 0.531,0.365 10 N14 5.521,4.865 7.146,5.26 1.625,0.396 10 Airbag Sensor Assembly 5.521,4.698 5.958,4.99 0.438,0.292 10 N5 1.146,0.896 1.917,1.25 0.771,0.354 10 BBL+ 1.594,0.802 2.115,1.292 0.521,0.49 10 4 1.177,1.792 1.865,2.281 0.688,0.49 10 BBL- 5.563,0.896 6.063,1.271 0.5,0.375 10 BBL+ 5.333,0.792 5.844,1.323 0.51,0.531 10 24 5.333,1.698 5.75,2.177 0.417,0.479 10 23 5.563,1.792 6.135,2.292 0.573,0.5 10 BBL- 1.583,1.698 2.073,2.333 0.49,0.635 10 3 1.135,3.042 1.771,3.427 0.635,0.385 10 BCL+ 1.583,2.948 2.01,3.531 0.427,0.583 10 1 2.896,3.833 3.375,4.26 0.479,0.427 10 1 1.177,3.938 1.823,4.375 0.646,0.438 10 BCL- 3.073,3.042 3.552,3.385 0.479,0.344 10 BCL+ 3.073,3.938 3.573,4.313 0.5,0.375 10 BCL- 1.583,3.833 1.927,4.406 0.344,0.573 10 2 2.896,2.948 3.344,3.469 0.448,0.521 10 2

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK CURRENT DTC
a.

Check for current DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:
·

DTCs indicating communication errors will be changed to DTCs indicating errors in initialization by turning the power switch off and then on (IG) again.

·

Codes other than current DTCs B1627, B1628, B1637, B1638, B1647 and 82 may be output at this time, but they are not related to this check.




Result:
Result Proceed to
Current DTC B1647 or 82 is output. A
Current DTC B1628 is output. B
Current DTC B1637 or B1638 is output. C
Current DTC B1627 is output. D
Current DTCs B1627, B1628, B1637, B1638, B1647 and 82 are not output. E



A

2.CHECK CONNECTORS

B

13.CHECK HISTORY DTC

C

21.CHECK CONNECTORS

D

28.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH

E

2.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly, side airbag sensor assembly LH and side No. 2 airbag sensor assembly LH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly, side airbag sensor assembly LH and side No. 2 airbag sensor assembly LH.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK FLOOR WIRE (OPEN)

NG

REPLACE FLOOR WIRE

3.CHECK FLOOR WIRE (OPEN)
a.
C238398C01
0.75,0.51 1.094,0.74 0.344,0.229 0.406,3.667 0.771,3.917 0.365,0.25 1.479,3.792 1.156,4.177 false 1.604,3.792 1.927,4.177 false 1.563,2.208 1.563,1.729 1.563,1.729 1.396,1.729 false 2.01,1.177 2.01,1.302 false 1.938,0.854 1.5,1.115 false 2.063,0.854 2.51,1.115 false 1.052,2.188 1.281,2.469 0.229,0.281 10 D 1.354,2.188 1.667,2.667 0.313,0.479 10 C 1.698,2.188 2.021,2.594 0.323,0.406 10 B 2,2.198 2.344,2.625 0.344,0.427 10 A 0.698,2.177 0.99,2.604 0.292,0.427 10 *1 2.49,2.51 2.885,2.979 0.396,0.469 10 *2 0.635,0.177 0.927,0.469 0.292,0.292 10 *a 0.375,3.271 0.708,3.635 0.333,0.365 10 *b 2.396,1.115 2.865,1.406 0.469,0.292 10 BBL+ 1.333,1.115 1.813,1.375 0.479,0.26 10 BBL- 0.854,0.542 1.198,0.844 0.344,0.302 10 N5 0.51,3.708 0.833,4.146 0.323,0.438 10 N8 1.802,4.188 2.323,4.469 0.521,0.281 10 BBL+ 1.01,4.198 1.5,4.531 0.49,0.333 10 BBL- 1.24,1.656 1.625,2.042 0.385,0.385 10 *3 1.948,1.323 2.188,1.667 0.24,0.344 10 *4
*1 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)


Using a service wire, connect terminals 24 (BBL+) and 23 (BBL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N8-4 (BBL+) - N8-3 (BBL-) Always Below 1 Ω



c.

Disconnect the service wire from connector B.


Result:
Proceed to
OK
NG



OK

4.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

4.CHECK FLOOR WIRE (SHORT)
a.
C238399C03
0.448,2.292 0.833,2.542 0.385,0.25 1.51,2.458 1.156,2.802 false 1.635,2.448 1.979,2.792 false 1.594,0.615 1.594,0.208 1.594,0.208 1.75,0.208 false 1.083,0.604 1.438,1 0.354,0.396 10 D 1.385,0.615 1.792,1.052 0.406,0.438 10 C 1.729,0.615 2.25,1.271 0.521,0.656 10 B 2.021,0.625 2.344,0.927 0.323,0.302 10 A 0.729,0.604 1.031,0.958 0.302,0.354 10 *1 2.51,0.938 2.958,1.365 0.448,0.427 10 *2 0.427,1.813 0.823,2.156 0.396,0.344 10 *a 0.563,2.333 0.927,2.656 0.365,0.323 10 N8 1.865,2.802 2.573,3.208 0.708,0.406 10 BBL+ 1.021,2.813 1.583,3.115 0.563,0.302 10 BBL- 1.813,0.135 2.208,0.469 0.396,0.333 10 *3
*1 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N8-4 (BBL+) - N8-3 (BBL-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

5.CHECK FLOOR WIRE (SHORT TO B+)
a.
C238399C03
0.448,2.292 0.833,2.542 0.385,0.25 1.51,2.458 1.156,2.802 false 1.635,2.448 1.979,2.792 false 1.594,0.615 1.594,0.208 1.594,0.208 1.75,0.208 false 1.083,0.604 1.438,1 0.354,0.396 10 D 1.385,0.615 1.792,1.052 0.406,0.438 10 C 1.729,0.615 2.25,1.271 0.521,0.656 10 B 2.021,0.625 2.344,0.927 0.323,0.302 10 A 0.729,0.604 1.031,0.958 0.302,0.354 10 *1 2.51,0.938 2.958,1.365 0.448,0.427 10 *2 0.427,1.813 0.823,2.156 0.396,0.344 10 *a 0.563,2.333 0.927,2.656 0.365,0.323 10 N8 1.865,2.802 2.573,3.208 0.708,0.406 10 BBL+ 1.021,2.813 1.583,3.115 0.563,0.302 10 BBL- 1.813,0.135 2.208,0.469 0.396,0.333 10 *3
*1 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
N8-4 (BBL+) - Body ground Power switch on (IG) Below 1 V
N8-3 (BBL-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

6.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

6.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
C238399C03
0.448,2.292 0.833,2.542 0.385,0.25 1.51,2.458 1.156,2.802 false 1.635,2.448 1.979,2.792 false 1.594,0.615 1.594,0.208 1.594,0.208 1.75,0.208 false 1.083,0.604 1.438,1 0.354,0.396 10 D 1.385,0.615 1.792,1.052 0.406,0.438 10 C 1.729,0.615 2.25,1.271 0.521,0.656 10 B 2.021,0.625 2.344,0.927 0.323,0.302 10 A 0.729,0.604 1.031,0.958 0.302,0.354 10 *1 2.51,0.938 2.958,1.365 0.448,0.427 10 *2 0.427,1.813 0.823,2.156 0.396,0.344 10 *a 0.563,2.333 0.927,2.656 0.365,0.323 10 N8 1.865,2.802 2.573,3.208 0.708,0.406 10 BBL+ 1.021,2.813 1.583,3.115 0.563,0.302 10 BBL- 1.813,0.135 2.208,0.469 0.396,0.333 10 *3
*1 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N8-4 (BBL+) - Body ground Always 1 MΩ or higher
N8-3 (BBL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK FLOOR WIRE (OPEN)

NG

REPLACE FLOOR WIRE

7.CHECK FLOOR WIRE (OPEN)
a.
C240589C02
0.635,3.615 0.969,3.833 0.333,0.219 0.969,0.552 1.281,0.771 0.313,0.219 1.448,3.719 1.073,4.073 false 1.625,3.719 2,4.073 false 1.823,0.677 1.563,1.021 false 1.938,0.677 2.198,1.021 false 1.531,4.125 1.531,4.302 false 1.698,2.281 1.698,1.76 1.698,1.76 1.479,1.76 false 1.052,2.26 1.438,2.531 0.385,0.271 10 D 1.354,2.26 1.75,2.604 0.396,0.344 10 C 1.948,2.26 2.24,2.573 0.292,0.313 10 B 2.26,2.26 2.521,2.531 0.26,0.271 10 A 0.677,2.26 1,2.552 0.323,0.292 10 *1 2.583,2.26 2.896,2.542 0.313,0.281 10 *2 0.917,4.083 1.333,4.271 0.417,0.188 10 BCL- 1.875,4.083 2.365,4.323 0.49,0.24 10 BCL+ 0.688,3.646 1.135,3.917 0.448,0.271 10 N14 1.052,0.583 1.385,0.771 0.333,0.188 10 N8 2.083,1.021 2.552,1.26 0.469,0.24 10 BCL- 1.385,1.021 1.906,1.292 0.521,0.271 10 BCL+ 1.323,1.688 1.677,1.958 0.354,0.271 10 *3 0.729,0.167 1.042,0.438 0.313,0.271 10 *a 0.458,3.271 0.792,3.542 0.333,0.271 10 *b 1.458,4.302 1.75,4.542 0.292,0.24 10 *4
*1 Side No. 2 Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly LH
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)
*b Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly LH)


Using a service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N8-1 (BCL+) - N8-2 (BCL-) Always Below 1 Ω



c.

Disconnect the service wire from connector C.


Result:
Proceed to
OK
NG



OK

8.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

8.CHECK FLOOR WIRE (SHORT)
a.
C238222C10
1.188,2.302 1.542,2.542 0.354,0.24 2.094,2.448 1.844,2.833 false 2.219,2.448 2.469,2.833 false 1.74,0.75 1.74,0.219 1.74,0.219 1.573,0.219 false 1.146,0.74 1.51,1.094 0.365,0.354 10 D 1.458,0.74 1.74,1.115 0.281,0.375 10 C 1.906,0.74 2.25,1.104 0.344,0.365 10 B 2.219,0.74 2.656,1.073 0.438,0.333 10 A 0.823,0.74 1.354,1.063 0.531,0.323 10 *1 2.458,0.74 2.792,1.021 0.333,0.281 10 *2 1.406,0.146 1.76,0.427 0.354,0.281 10 *3 0.979,1.875 1.302,2.208 0.323,0.333 10 *a 1.292,2.344 1.688,2.708 0.396,0.365 10 N8 2.354,2.844 2.885,3.094 0.531,0.25 10 BCL- 1.688,2.844 2.156,3.104 0.469,0.26 10 BCL+
*1 Side No. 2 Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly LH
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N8-1 (BCL+) - N8-2 (BCL-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

9.CHECK FLOOR WIRE (SHORT TO B+)
a.
C238222C10
1.188,2.302 1.542,2.542 0.354,0.24 2.094,2.448 1.844,2.833 false 2.219,2.448 2.469,2.833 false 1.74,0.75 1.74,0.219 1.74,0.219 1.573,0.219 false 1.146,0.74 1.51,1.094 0.365,0.354 10 D 1.458,0.74 1.74,1.115 0.281,0.375 10 C 1.906,0.74 2.25,1.104 0.344,0.365 10 B 2.219,0.74 2.656,1.073 0.438,0.333 10 A 0.823,0.74 1.354,1.063 0.531,0.323 10 *1 2.458,0.74 2.792,1.021 0.333,0.281 10 *2 1.406,0.146 1.76,0.427 0.354,0.281 10 *3 0.979,1.875 1.302,2.208 0.323,0.333 10 *a 1.292,2.344 1.688,2.708 0.396,0.365 10 N8 2.354,2.844 2.885,3.094 0.531,0.25 10 BCL- 1.688,2.844 2.156,3.104 0.469,0.26 10 BCL+
*1 Side No. 2 Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly LH
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
N8-1 (BCL+) - Body ground Power switch on (IG) Below 1 V
N8-2 (BCL-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

10.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

10.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
C238222C10
1.188,2.302 1.542,2.542 0.354,0.24 2.094,2.448 1.844,2.833 false 2.219,2.448 2.469,2.833 false 1.74,0.75 1.74,0.219 1.74,0.219 1.573,0.219 false 1.146,0.74 1.51,1.094 0.365,0.354 10 D 1.458,0.74 1.74,1.115 0.281,0.375 10 C 1.906,0.74 2.25,1.104 0.344,0.365 10 B 2.219,0.74 2.656,1.073 0.438,0.333 10 A 0.823,0.74 1.354,1.063 0.531,0.323 10 *1 2.458,0.74 2.792,1.021 0.333,0.281 10 *2 1.406,0.146 1.76,0.427 0.354,0.281 10 *3 0.979,1.875 1.302,2.208 0.323,0.333 10 *a 1.292,2.344 1.688,2.708 0.396,0.365 10 N8 2.354,2.844 2.885,3.094 0.531,0.25 10 BCL- 1.688,2.844 2.156,3.104 0.469,0.26 10 BCL+
*1 Side No. 2 Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly LH
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N8-1 (BCL+) - Body ground Always 1 MΩ or higher
N8-2 (BCL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH

NG

REPLACE FLOOR WIRE

11.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH
a.
C238328C01
0.719,0.813 1.073,1.24 0.354,0.427 10 false *1 1.104,0.813 1.354,1.25 0.25,0.438 10 false D 1.26,0.813 1.573,1.167 0.313,0.354 10 false C 1.729,0.813 2.031,1.073 0.302,0.26 10 false B 1.885,0.813 2.135,1.073 0.25,0.26 10 false A 2.323,1.135 2.646,1.385 0.323,0.25 10 false *2
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly


Connect the connectors to the side No. 2 airbag sensor assembly LH and airbag sensor assembly.


b.

Interchange the side airbag sensor assembly LH with RH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1642, B1647, 81 and 82 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1647 or 82 is output. A
DTC B1642 or 81 is output. B
DTCs B1642, B1647, 81 and 82 are not output. C


h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.



A

12.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH

B

REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH

C

12.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH
a.
C238223C02
0.969,1 1.313,1.469 0.344,0.469 10 false *1 2.271,1.01 2.51,1.375 0.24,0.365 10 false *2 2.042,1.01 2.323,1.375 0.281,0.365 10 false A 1.885,1.01 2.135,1.406 0.25,0.396 10 false B 1.438,1.01 1.802,1.448 0.365,0.438 10 false C 1.281,1.01 1.542,1.417 0.26,0.406 10 false D
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly LH


Interchange the side No. 2 airbag sensor assembly LH with RH and connect the connectors.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1642, B1647, 81 and 82 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTCs B1642, B1647, 81 and 82 are not output. A
DTC B1647 or 82 is output. B
DTC B1642 or 81 is output. C


g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



i.

Return the side No. 2 airbag sensor assembly LH and RH to their original positions and connect the connectors.



A

B

C

REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH

13.CHECK HISTORY DTC
a.

Check for history DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than history DTC B1627 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
History DTC B1627 is not output. A
History DTC B1627 is output. B



A

14.CHECK CONNECTORS

B

20.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH
14.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly and side airbag sensor assembly LH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly and side airbag sensor assembly LH.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

15.CHECK FLOOR WIRE (OPEN)

NG

REPLACE FLOOR WIRE

15.CHECK FLOOR WIRE (OPEN)
a.
C238398C01
0.75,0.51 1.094,0.74 0.344,0.229 0.406,3.667 0.771,3.917 0.365,0.25 1.479,3.792 1.156,4.177 false 1.604,3.792 1.927,4.177 false 1.563,2.208 1.563,1.729 1.563,1.729 1.396,1.729 false 2.01,1.177 2.01,1.302 false 1.938,0.854 1.5,1.115 false 2.063,0.854 2.51,1.115 false 1.052,2.188 1.281,2.469 0.229,0.281 10 D 1.354,2.188 1.667,2.667 0.313,0.479 10 C 1.698,2.188 2.021,2.594 0.323,0.406 10 B 2,2.198 2.344,2.625 0.344,0.427 10 A 0.698,2.177 0.99,2.604 0.292,0.427 10 *1 2.49,2.51 2.885,2.979 0.396,0.469 10 *2 0.635,0.177 0.927,0.469 0.292,0.292 10 *a 0.375,3.271 0.708,3.635 0.333,0.365 10 *b 2.396,1.115 2.865,1.406 0.469,0.292 10 BBL+ 1.333,1.115 1.813,1.375 0.479,0.26 10 BBL- 0.854,0.542 1.198,0.844 0.344,0.302 10 N5 0.51,3.708 0.833,4.146 0.323,0.438 10 N8 1.802,4.188 2.323,4.469 0.521,0.281 10 BBL+ 1.01,4.198 1.5,4.531 0.49,0.333 10 BBL- 1.24,1.656 1.625,2.042 0.385,0.385 10 *3 1.948,1.323 2.188,1.667 0.24,0.344 10 *4
*1 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)


Using a service wire, connect terminals 24 (BBL+) and 23 (BBL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N8-4 (BBL+) - N8-3 (BBL-) Always Below 1 Ω



c.

Disconnect the service wire from connector B.


Result:
Proceed to
OK
NG



OK

16.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

16.CHECK FLOOR WIRE (SHORT)
a.
C238399C03
0.448,2.292 0.833,2.542 0.385,0.25 1.51,2.458 1.156,2.802 false 1.635,2.448 1.979,2.792 false 1.594,0.615 1.594,0.208 1.594,0.208 1.75,0.208 false 1.083,0.604 1.438,1 0.354,0.396 10 D 1.385,0.615 1.792,1.052 0.406,0.438 10 C 1.729,0.615 2.25,1.271 0.521,0.656 10 B 2.021,0.625 2.344,0.927 0.323,0.302 10 A 0.729,0.604 1.031,0.958 0.302,0.354 10 *1 2.51,0.938 2.958,1.365 0.448,0.427 10 *2 0.427,1.813 0.823,2.156 0.396,0.344 10 *a 0.563,2.333 0.927,2.656 0.365,0.323 10 N8 1.865,2.802 2.573,3.208 0.708,0.406 10 BBL+ 1.021,2.813 1.583,3.115 0.563,0.302 10 BBL- 1.813,0.135 2.208,0.469 0.396,0.333 10 *3
*1 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N8-4 (BBL+) - N8-3 (BBL-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

17.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

17.CHECK FLOOR WIRE (SHORT TO B+)
a.
C238399C03
0.448,2.292 0.833,2.542 0.385,0.25 1.51,2.458 1.156,2.802 false 1.635,2.448 1.979,2.792 false 1.594,0.615 1.594,0.208 1.594,0.208 1.75,0.208 false 1.083,0.604 1.438,1 0.354,0.396 10 D 1.385,0.615 1.792,1.052 0.406,0.438 10 C 1.729,0.615 2.25,1.271 0.521,0.656 10 B 2.021,0.625 2.344,0.927 0.323,0.302 10 A 0.729,0.604 1.031,0.958 0.302,0.354 10 *1 2.51,0.938 2.958,1.365 0.448,0.427 10 *2 0.427,1.813 0.823,2.156 0.396,0.344 10 *a 0.563,2.333 0.927,2.656 0.365,0.323 10 N8 1.865,2.802 2.573,3.208 0.708,0.406 10 BBL+ 1.021,2.813 1.583,3.115 0.563,0.302 10 BBL- 1.813,0.135 2.208,0.469 0.396,0.333 10 *3
*1 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
N8-4 (BBL+) - Body ground Power switch on (IG) Below 1 V
N8-3 (BBL-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

18.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

18.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
C238399C03
0.448,2.292 0.833,2.542 0.385,0.25 1.51,2.458 1.156,2.802 false 1.635,2.448 1.979,2.792 false 1.594,0.615 1.594,0.208 1.594,0.208 1.75,0.208 false 1.083,0.604 1.438,1 0.354,0.396 10 D 1.385,0.615 1.792,1.052 0.406,0.438 10 C 1.729,0.615 2.25,1.271 0.521,0.656 10 B 2.021,0.625 2.344,0.927 0.323,0.302 10 A 0.729,0.604 1.031,0.958 0.302,0.354 10 *1 2.51,0.938 2.958,1.365 0.448,0.427 10 *2 0.427,1.813 0.823,2.156 0.396,0.344 10 *a 0.563,2.333 0.927,2.656 0.365,0.323 10 N8 1.865,2.802 2.573,3.208 0.708,0.406 10 BBL+ 1.021,2.813 1.583,3.115 0.563,0.302 10 BBL- 1.813,0.135 2.208,0.469 0.396,0.333 10 *3
*1 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N8-4 (BBL+) - Body ground Always 1 MΩ or higher
N8-3 (BBL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

19.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH

NG

REPLACE FLOOR WIRE

19.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH
a.
C238328C01
0.719,0.813 1.073,1.24 0.354,0.427 10 false *1 1.104,0.813 1.354,1.25 0.25,0.438 10 false D 1.26,0.813 1.573,1.167 0.313,0.354 10 false C 1.729,0.813 2.031,1.073 0.302,0.26 10 false B 1.885,0.813 2.135,1.073 0.25,0.26 10 false A 2.323,1.135 2.646,1.385 0.323,0.25 10 false *2
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly


Connect the connector to the airbag sensor assembly.


b.

Interchange the side airbag sensor assembly LH with RH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1623 and B1628 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTCs B1623 and B1628 are not output. A
DTC B1628 is output. B
DTC B1623 is output. C


h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.



A

B

C

REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH

20.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH
a.
C238328C01
0.719,0.813 1.073,1.24 0.354,0.427 10 false *1 1.104,0.813 1.354,1.25 0.25,0.438 10 false D 1.26,0.813 1.573,1.167 0.313,0.354 10 false C 1.729,0.813 2.031,1.073 0.302,0.26 10 false B 1.885,0.813 2.135,1.073 0.25,0.26 10 false A 2.323,1.135 2.646,1.385 0.323,0.25 10 false *2
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Interchange the side airbag sensor assembly LH with RH and connect the connectors.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1622 and B1627 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTCs B1622 and B1627 are not output. A
DTC B1627 is output. B
DTC B1622 is output. C


i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



k.

Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.



A

B

C

REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH

21.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the side airbag sensor assembly LH and side No. 2 airbag sensor assembly LH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the side airbag sensor assembly LH and side No. 2 airbag sensor assembly LH.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

22.CHECK FLOOR WIRE (OPEN)

NG

REPLACE FLOOR WIRE

22.CHECK FLOOR WIRE (OPEN)
a.
C240589C02
0.635,3.615 0.969,3.833 0.333,0.219 0.969,0.552 1.281,0.771 0.313,0.219 1.448,3.719 1.073,4.073 false 1.625,3.719 2,4.073 false 1.823,0.677 1.563,1.021 false 1.938,0.677 2.198,1.021 false 1.531,4.125 1.531,4.302 false 1.698,2.281 1.698,1.76 1.698,1.76 1.479,1.76 false 1.052,2.26 1.438,2.531 0.385,0.271 10 D 1.354,2.26 1.75,2.604 0.396,0.344 10 C 1.948,2.26 2.24,2.573 0.292,0.313 10 B 2.26,2.26 2.521,2.531 0.26,0.271 10 A 0.677,2.26 1,2.552 0.323,0.292 10 *1 2.583,2.26 2.896,2.542 0.313,0.281 10 *2 0.917,4.083 1.333,4.271 0.417,0.188 10 BCL- 1.875,4.083 2.365,4.323 0.49,0.24 10 BCL+ 0.688,3.646 1.135,3.917 0.448,0.271 10 N14 1.052,0.583 1.385,0.771 0.333,0.188 10 N8 2.083,1.021 2.552,1.26 0.469,0.24 10 BCL- 1.385,1.021 1.906,1.292 0.521,0.271 10 BCL+ 1.323,1.688 1.677,1.958 0.354,0.271 10 *3 0.729,0.167 1.042,0.438 0.313,0.271 10 *a 0.458,3.271 0.792,3.542 0.333,0.271 10 *b 1.458,4.302 1.75,4.542 0.292,0.24 10 *4
*1 Side No. 2 Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly LH
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)
*b Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly LH)


Using a service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N8-1 (BCL+) - N8-2 (BCL-) Always Below 1 Ω



c.

Disconnect the service wire from connector C.


Result:
Proceed to
OK
NG



OK

23.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

23.CHECK FLOOR WIRE (SHORT)
a.
C238222C10
1.188,2.302 1.542,2.542 0.354,0.24 2.094,2.448 1.844,2.833 false 2.219,2.448 2.469,2.833 false 1.74,0.75 1.74,0.219 1.74,0.219 1.573,0.219 false 1.146,0.74 1.51,1.094 0.365,0.354 10 D 1.458,0.74 1.74,1.115 0.281,0.375 10 C 1.906,0.74 2.25,1.104 0.344,0.365 10 B 2.219,0.74 2.656,1.073 0.438,0.333 10 A 0.823,0.74 1.354,1.063 0.531,0.323 10 *1 2.458,0.74 2.792,1.021 0.333,0.281 10 *2 1.406,0.146 1.76,0.427 0.354,0.281 10 *3 0.979,1.875 1.302,2.208 0.323,0.333 10 *a 1.292,2.344 1.688,2.708 0.396,0.365 10 N8 2.354,2.844 2.885,3.094 0.531,0.25 10 BCL- 1.688,2.844 2.156,3.104 0.469,0.26 10 BCL+
*1 Side No. 2 Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly LH
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N8-1 (BCL+) - N8-2 (BCL-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

24.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

24.CHECK FLOOR WIRE (SHORT TO B+)
a.
C238222C10
1.188,2.302 1.542,2.542 0.354,0.24 2.094,2.448 1.844,2.833 false 2.219,2.448 2.469,2.833 false 1.74,0.75 1.74,0.219 1.74,0.219 1.573,0.219 false 1.146,0.74 1.51,1.094 0.365,0.354 10 D 1.458,0.74 1.74,1.115 0.281,0.375 10 C 1.906,0.74 2.25,1.104 0.344,0.365 10 B 2.219,0.74 2.656,1.073 0.438,0.333 10 A 0.823,0.74 1.354,1.063 0.531,0.323 10 *1 2.458,0.74 2.792,1.021 0.333,0.281 10 *2 1.406,0.146 1.76,0.427 0.354,0.281 10 *3 0.979,1.875 1.302,2.208 0.323,0.333 10 *a 1.292,2.344 1.688,2.708 0.396,0.365 10 N8 2.354,2.844 2.885,3.094 0.531,0.25 10 BCL- 1.688,2.844 2.156,3.104 0.469,0.26 10 BCL+
*1 Side No. 2 Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly LH
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
N8-1 (BCL+) - Body ground Power switch on (IG) Below 1 V
N8-2 (BCL-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

25.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

25.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
C238222C10
1.188,2.302 1.542,2.542 0.354,0.24 2.094,2.448 1.844,2.833 false 2.219,2.448 2.469,2.833 false 1.74,0.75 1.74,0.219 1.74,0.219 1.573,0.219 false 1.146,0.74 1.51,1.094 0.365,0.354 10 D 1.458,0.74 1.74,1.115 0.281,0.375 10 C 1.906,0.74 2.25,1.104 0.344,0.365 10 B 2.219,0.74 2.656,1.073 0.438,0.333 10 A 0.823,0.74 1.354,1.063 0.531,0.323 10 *1 2.458,0.74 2.792,1.021 0.333,0.281 10 *2 1.406,0.146 1.76,0.427 0.354,0.281 10 *3 0.979,1.875 1.302,2.208 0.323,0.333 10 *a 1.292,2.344 1.688,2.708 0.396,0.365 10 N8 2.354,2.844 2.885,3.094 0.531,0.25 10 BCL- 1.688,2.844 2.156,3.104 0.469,0.26 10 BCL+
*1 Side No. 2 Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly LH
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N8-1 (BCL+) - Body ground Always 1 MΩ or higher
N8-2 (BCL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

26.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH

NG

REPLACE FLOOR WIRE

26.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH
a.
C238328C01
0.719,0.813 1.073,1.24 0.354,0.427 10 false *1 1.104,0.813 1.354,1.25 0.25,0.438 10 false D 1.26,0.813 1.573,1.167 0.313,0.354 10 false C 1.729,0.813 2.031,1.073 0.302,0.26 10 false B 1.885,0.813 2.135,1.073 0.25,0.26 10 false A 2.323,1.135 2.646,1.385 0.323,0.25 10 false *2
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly


Connect the connector to the side No. 2 airbag sensor assembly LH.


b.

Interchange the side airbag sensor assembly LH with RH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1632, B1633, B1637 and B1638 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1637 or B1638 is output. A
DTC B1632 or B1633 is output. B
DTCs B1632, B1633, B1637 and B1638 are not output. C


h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.



A

27.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH

B

REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH

C

27.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH
a.
C238223C02
0.969,1 1.313,1.469 0.344,0.469 10 false *1 2.271,1.01 2.51,1.375 0.24,0.365 10 false *2 2.042,1.01 2.323,1.375 0.281,0.365 10 false A 1.885,1.01 2.135,1.406 0.25,0.396 10 false B 1.438,1.01 1.802,1.448 0.365,0.438 10 false C 1.281,1.01 1.542,1.417 0.26,0.406 10 false D
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly LH


Interchange the side No. 2 airbag sensor assembly LH with RH and connect the connectors.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1632, B1633, B1637 and B1638 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTCs B1632, B1633, B1637 and B1638 are not output. A
DTC B1637 or B1638 is output. B
DTC B1632 or B1633 is output. C


g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



i.

Return the side No. 2 airbag sensor assembly LH and RH to their original positions and connect the connectors.



A

B

C

REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH

28.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH
a.
C238328C01
0.719,0.813 1.073,1.24 0.354,0.427 10 false *1 1.104,0.813 1.354,1.25 0.25,0.438 10 false D 1.26,0.813 1.573,1.167 0.313,0.354 10 false C 1.729,0.813 2.031,1.073 0.302,0.26 10 false B 1.885,0.813 2.135,1.073 0.25,0.26 10 false A 2.323,1.135 2.646,1.385 0.323,0.25 10 false *2
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Interchange the side airbag sensor assembly LH with RH and connect the connectors.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1622 and B1627 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTCs B1622 and B1627 are not output. A
DTC B1627 is output. B
DTC B1622 is output. C


i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



k.

Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.



A

B

C

REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH