Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2012.02–2015.04
RM2040EQ _58 Vehicle Interior _014727 SUPPLEMENTAL RESTRAINT SYSTEMS _0075078 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  SRS Warning Light Remains ON  


DESCRIPTION

The SRS warning light is located on the combination meter assembly.

When the SRS is normal, the SRS warning light comes on for approximately 6 seconds after the power switch is turned from off to on (IG), and then goes off automatically.

If there is a malfunction in the SRS, the SRS warning light comes on to inform the driver of a problem.

When terminals TC and CG of the DLC3 are connected, the DTC is displayed by blinking of the SRS warning light.

The SRS is equipped with a voltage-increase circuit (DC-DC converter) in the airbag sensor assembly in case the source voltage drops.

When the auxiliary battery voltage drops, the voltage-increase circuit (DC-DC converter) functions to increase the voltage of the SRS to normal voltage. In addition, when the voltage drops, the SRS warning light will illuminate.

A malfunction in this circuit is not stored in the airbag sensor assembly. The SRS warning light automatically goes off when the source voltage returns to normal.

The signal to illuminate the SRS warning light is transmitted from the airbag sensor assembly to the combination meter assembly through the CAN communication system.

WIRING DIAGRAM

C249367E01
0.177,1.813 1.594,2.271 1.417,0.458 10 false from Auxiliary Battery 5.125,0.74 5.448,1.115 0.323,0.375 10 false A/B 2.094,1.427 2.917,1.823 0.823,0.396 10 false METER-IG2 2.052,1.979 2.979,2.313 0.927,0.333 10 false ECU-B NO. 1 3.115,2.365 3.469,2.76 0.354,0.396 10 false ES 2.927,1.729 3.26,2.042 0.333,0.313 10 false 1 2.865,1.167 3.313,1.635 0.448,0.469 10 false 13 5.813,1.125 6.26,1.5 0.448,0.375 10 false 13 4.094,1.115 4.479,1.604 0.385,0.49 10 false 16 2.938,2.271 3.167,2.594 0.229,0.323 10 false 7 6.052,0.583 6.396,0.917 0.344,0.333 10 false IG2 3.615,1.26 4.313,1.552 0.698,0.292 10 false CANH 3.625,1.823 4.146,2.177 0.521,0.354 10 false CANL 6.052,2.365 6.344,2.656 0.292,0.292 10 false E1 6.052,2.875 6.375,3.167 0.323,0.292 10 false E2 6.01,3.625 6.354,3.958 0.344,0.333 10 false I47 3.052,3.604 3.469,4.104 0.417,0.5 10 false I18 6.01,3.792 6.938,4.51 0.927,0.719 10 false Airbag Sensor Assembly 3.052,3.771 4.26,4.354 1.208,0.583 10 false Combination Meter Assembly 5.813,1.677 6.229,2.01 0.417,0.333 10 false 22 6.052,1.26 6.594,1.677 0.542,0.417 10 false CANH 6.052,1.813 6.531,2.25 0.479,0.438 10 false CANL 5.813,0.49 6.135,0.885 0.323,0.396 10 false 21 5.813,2.271 6.198,2.583 0.385,0.313 10 false 25 5.813,2.781 6.115,3.073 0.302,0.292 10 false 26 4.094,1.677 4.427,2.115 0.333,0.438 10 false 15 0.563,1.26 1.719,1.625 1.156,0.365 10 false from IG2 Relay 3.323,0.583 4.354,0.917 1.031,0.333 10 false from IG2 Relay 3.115,1.823 3.448,2.156 0.333,0.333 10 false B 3.104,1.271 3.469,1.563 0.365,0.292 10 false IG+ 0.74,4.177 2.615,4.448 1.875,0.271 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK SRS WARNING LIGHT OPERATION
a.

Check the SRS warning light operation approximately 6 seconds after the power switch is turned on (IG).


Result:
SRS Warning Light Illumination Proceed to
Remains on A
Goes off and then comes on again B



A

2.CHECK AUXILIARY BATTERY VOLTAGE

B

6.CHECK CAN COMMUNICATION SYSTEM
2.CHECK AUXILIARY BATTERY VOLTAGE
a.

Measure the voltage of the auxiliary battery.

Standard Voltage:

11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK CONNECTOR

NG

INSPECT CHARGING SYSTEM AND AUXILIARY BATTERY

3.CHECK CONNECTOR
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connector is properly connected to the airbag sensor assembly.

OK:
:

The connector is properly connected.


HINT:

If the connector is not connected securely, reconnect the connector and proceed to the next inspection.



d.

Disconnect the connector from the airbag sensor assembly.


e.

Check that the terminal of the connector is not damaged.

OK:

The terminal is not deformed or damaged.



Result:
Proceed to
OK
NG



OK

4.CHECK WIRE HARNESS (AIRBAG SENSOR ASSEMBLY - BODY GROUND)

NG

REPLACE WIRE HARNESS

4.CHECK WIRE HARNESS (AIRBAG SENSOR ASSEMBLY - BODY GROUND)
a.
C126715C06
0.49,0.865 0.833,1.094 0.344,0.229 1.292,1.281 0.854,1.708 false 1.656,1.281 1.219,1.708 false 1.75,1.292 2.188,1.719 false 0.031,0.031 0.313,0.396 0.281,0.365 10 *a 0.573,0.896 0.948,1.219 0.375,0.323 10 I47 0.729,1.719 1.135,2.073 0.406,0.354 10 IG2 1.125,1.729 1.49,2.063 0.365,0.333 10 E1 2.146,1.729 2.521,2 0.375,0.271 10 E2
*a Front view of wire harness connector
(to Airbag Sensor Assembly)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Operate all components of the electrical system (defogger, wipers, headlights, heater blower, etc.).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I47-21 (IG2) - Body ground Power switch on (IG) 8 to 16 V



e.

Turn the power switch off.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I47-25 (E1) - Body ground Always Below 1 Ω
I47-26 (E2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK SRS WARNING LIGHT

NG

REPLACE WIRE HARNESS

5.CHECK SRS WARNING LIGHT
a.

Turn the power switch on (IG).


b.

Check the SRS warning light condition.

OK:

After the primary check period, the SRS warning light goes off for approximately 10 seconds and turns back on.


HINT:

The primary check period is approximately 6 seconds after the power switch is turned on (IG).



Result:
Proceed to
OK
NG



OK

NG

REPLACE COMBINATION METER ASSEMBLY

6.CHECK CAN COMMUNICATION SYSTEM
a.

Use the intelligent tester to check if the CAN communication system is functioning normally.

HINT:
·

Refer to Bus Check for the CAN communication system.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

The airbag sensor assembly is connected to the CAN communication system. Therefore, before starting troubleshooting, make sure to check that there is no trouble in the CAN communication system.




Result:
Result Proceed to
DTC is not output A
DTC is output B



A

7.CHECK AUXILIARY BATTERY VOLTAGE

B

7.CHECK AUXILIARY BATTERY VOLTAGE
a.

Measure the voltage of the auxiliary battery.

Standard Voltage:

11 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK CONNECTOR

NG

INSPECT CHARGING SYSTEM AND AUXILIARY BATTERY

8.CHECK CONNECTOR
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connector is properly connected to the airbag sensor assembly.

OK:
:

The connector is properly connected.


HINT:

If the connector is not connected securely, reconnect the connector and proceed to the next inspection.



d.

Disconnect the connector from the airbag sensor assembly.


e.

Check that the terminal of the connector is not damaged.

OK:
The terminal is not deformed or damaged.:


Result:
Proceed to
OK
NG



OK

9.CHECK WIRE HARNESS (AIRBAG SENSOR ASSEMBLY - BODY GROUND)

NG

REPLACE WIRE HARNESS

9.CHECK WIRE HARNESS (AIRBAG SENSOR ASSEMBLY - BODY GROUND)
a.
C126715C06
0.49,0.865 0.833,1.094 0.344,0.229 1.292,1.281 0.854,1.708 false 1.656,1.281 1.219,1.708 false 1.75,1.292 2.188,1.719 false 0.031,0.031 0.313,0.396 0.281,0.365 10 *a 0.573,0.896 0.948,1.219 0.375,0.323 10 I47 0.729,1.719 1.135,2.073 0.406,0.354 10 IG2 1.125,1.729 1.49,2.063 0.365,0.333 10 E1 2.146,1.729 2.521,2 0.375,0.271 10 E2
*a Front view of wire harness connector
(to Airbag Sensor Assembly)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Operate all components of the electrical system (defogger, wipers, headlights, heater blower, etc.).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I47-21 (IG2) - Body ground Power switch on (IG) 8 to 16 V



e.

Turn the power switch off.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I47-25 (E1) - Body ground Always Below 1 Ω
I47-26 (E2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.CHECK CONNECTOR

NG

REPLACE WIRE HARNESS

10.CHECK CONNECTOR
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



b.

Check that the connector is properly connected to the combination meter assembly.

OK:

The connector is properly connected.


HINT:

If the connector is not connected securely, reconnect the connector and proceed to the next inspection.



c.

Disconnect the connector from the combination meter assembly.


d.

Check that the terminal of the connector is not damaged.

OK:

The terminal is not deformed or damaged.



Result:
Proceed to
OK
NG



OK

11.CHECK WIRE HARNESS (COMBINATION METER ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE CONNECTOR

11.CHECK WIRE HARNESS (COMBINATION METER ASSEMBLY - BODY GROUND)
a.
C126720C05
0.125,0.406 0.479,0.635 0.354,0.229 0.844,1.365 0.51,1.552 false 0.833,1.125 0.5,0.927 false 1.792,1.208 2.167,1.823 false 0.094,0.052 0.354,0.323 0.26,0.271 10 *a 0.25,1.479 0.698,1.813 0.448,0.333 10 IG+ 2.094,1.854 2.5,2.083 0.406,0.229 10 ES 0.375,0.833 0.698,1.135 0.323,0.302 10 B 0.219,0.438 0.667,0.729 0.448,0.292 10 I18
*a Front view of wire harness connector
(to Combination Meter Assembly)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I18-13 (IG+) - Body ground Power switch on (IG) 11 to 14 V
I18-1 (B) - Body ground Power switch off 11 to 14 V



d.

Turn the power switch off.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-7 (ES) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

12.CHECK SRS WARNING LIGHT

NG

REPAIR OR REPLACE WIRE HARNESS

12.CHECK SRS WARNING LIGHT
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



b.

Connect the connector to the combination meter assembly.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG).


e.

Check the SRS warning light condition.

OK:

After the primary check period, the SRS warning light goes off for approximately 10 seconds and turns back on.


HINT:

The primary check period is approximately 6 seconds after the power switch is turned on (IG).



Result:
Proceed to
OK
NG



OK

NG

REPLACE COMBINATION METER ASSEMBLY