Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › 2012.02–2015.04
RM2040EQ _56 Audio / Visual / Telematics _014716 AUDIO / VIDEO _0076806 AUDIO AND VISUAL SYSTEM Y

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use the following procedure to troubleshoot the audio and visual system.

·

*: Use the intelligent tester.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
·

When troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.

·

Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.

·

The following 5 items are important points in problem analysis:

What Vehicle model, system name
When Date, time, occurrence frequency
Where Road conditions
Under what conditions? Driving conditions, weather conditions
How did it happen? Problem symptoms


Result:
Proceed to
NEXT



NEXT

3.INSPECT AUXILIARY BATTERY VOLTAGE
3.INSPECT AUXILIARY BATTERY VOLTAGE
a.

Measure the auxiliary battery voltage with the power switch off.

Standard Voltage:

11 to 14 V


HINT:

If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.



Result:
Proceed to
NEXT



NEXT

4.CHECK CABIN
4.CHECK CABIN
a.

Check that condensation is not likely to occur in the cabin, and that the temperature is not high or extremely low in the cabin.

OK:

Condensation is not likely being produced and the temperature is not high or extremely low.


HINT:
·

A humid cabin and a rapid change in temperature may lead to condensation. Condensation in the cabin may cause a short circuit.

·

The audio and visual system may not operate normally when the temperature is -20°C (-4°F) or lower, or 65°C (149°F) or higher.




Result:
Proceed to
OK
NG



OK

5.CHECK CAN COMMUNICATION SYSTEM*

NG

SET CABIN TO APPROPRIATE TEMPERATURE

5.CHECK CAN COMMUNICATION SYSTEM*
a.

Check for DTC output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

Result:
Result Proceed to
CAN DTCs are not output. A
CAN DTCs are output. B




A

6.CHECK FOR DTC*

B

6.CHECK FOR DTC*
a.

Refer to DTC Check/Clear.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR

Result:
Result Proceed to
DTCs are output. A
DTCs are not output. B




A

7.DTC CLEAR*

B

10.PROBLEM SYMPTOMS TABLE
7.DTC CLEAR*
a.

Refer to DTC Check/Clear.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR

HINT:

The present DTCs may not indicate actual malfunctions depending on the vehicle operating conditions.



Result:
Proceed to
NEXT



NEXT

8.RECHECK FOR DTC*
8.RECHECK FOR DTC*
a.

Refer to DTC Check/Clear.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR

Result:
Result Proceed to
DTCs are output. A
DTCs are not output. B


HINT:
·

Even if the malfunction symptom is not confirmed, check for DTCs. This is because the system stores history DTCs.

·

If more information is needed, perform a recheck using the "System Check Mode" screen after rechecking for DTCs using the intelligent tester.

·

Check the DTCs and inspect the area that the code indicates.





A

9.DIAGNOSTIC TROUBLE CODE CHART

B

10.PROBLEM SYMPTOMS TABLE
9.DIAGNOSTIC TROUBLE CODE CHART
a.

Find the output code in Diagnostic Trouble Code Chart.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART


Result:
Proceed to
NEXT



NEXT

12.CHECK CIRCUIT
10.PROBLEM SYMPTOMS TABLE
a.

Refer to Problem Symptoms Table.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault is not listed in Problem Symptoms Table. A
Fault is listed in Problem Symptoms Table. B


HINT:

If the symptom does not recur and no DTCs are output, attempt to reproduce the symptoms.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING




A

11.PERFORM TROUBLESHOOTING BASED ON MALFUNCTION SYMPTOM

B

12.CHECK CIRCUIT
11.PERFORM TROUBLESHOOTING BASED ON MALFUNCTION SYMPTOM

Result:
Proceed to
NEXT



NEXT

12.CHECK CIRCUIT
12.CHECK CIRCUIT
a.

Adjust, repair or replace as necessary.


Result:
Proceed to
NEXT



NEXT

13.RECHECK FOR DTC*
13.RECHECK FOR DTC*
a.

After clearing DTCs, recheck for DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212
Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Proceed to
NEXT



NEXT

14.PERFORM CONFIRMATION TEST
14.PERFORM CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END