Each solenoid adjusts pressure which affects each wheel cylinder according to signals from the skid control ECU and controls the vehicle.
The master cut solenoid is closed and blocks the regulator pressure from the electronically controlled brake system control pressure when the system is normal. The master cut solenoid is open and sends the master cylinder and regulator hydraulic pressure to the non-assisted brake wheel cylinders during fail-safe operation during a system malfunction.
If the supply voltage decreases, a drop in current may cause a DTCs to be stored.
| DTC No. | Detection Item | INF Code | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|---|
| C1211/25 | SLA Linear Solenoid | 21
22 23 24 |
·
INF Code: 21 ·
Excess current is applied for 0.05 seconds or more. ·
INF Code: 22 ·
An open is detected for 0.05 seconds or more while the solenoid is OFF. ·
INF Code: 23 ·
An open is detected for 0.05 seconds or more while the solenoid is ON. ·
INF Code: 24 ·
A short to +B or voltage leak is detected for 0.05 seconds. |
·
INF Code: 21, 22, 24 ·
Brake booster with master cylinder assembly ·
INF Code: 23 ·
Supply voltage reduced ·
Brake booster with master cylinder assembly |
Electronically controlled brake system DTC |
| C1212/26 | SLR Linear Solenoid | 31
32 33 34 |
·
INF Code: 31 ·
Excess current is applied for 0.05 seconds or more. ·
INF Code: 32 ·
An open is detected for 0.05 seconds or more while the solenoid is OFF. ·
INF Code: 33 ·
An open is detected for 0.05 seconds or more while the solenoid is ON. ·
INF Code: 34 ·
A short to +B or voltage leak is detected for 0.05 seconds. |
·
INF Code: 31, 32, 34 ·
Brake booster with master cylinder assembly ·
INF Code: 33 ·
Supply voltage reduced ·
Brake booster with master cylinder assembly |
Electronically controlled brake system DTC |
| C1225/31 | SA1 Solenoid Circuit | 41
42 43 44 |
·
INF Code: 41 ·
Excess current is applied for 0.05 seconds or more. ·
INF Code: 42 ·
An open is detected for 0.05 seconds or more while the solenoid is OFF. ·
INF Code: 43 ·
An open is detected for 0.05 seconds or more while the solenoid is ON. ·
INF Code: 44 ·
A short to +B or voltage leak is detected for 0.05 seconds. |
·
INF Code: 41, 42, 44 ·
Brake booster with master cylinder assembly ·
INF Code: 43 ·
Supply voltage reduced ·
Brake booster with master cylinder assembly |
Electronically controlled brake system DTC |
| C1226/32 | SA2 Solenoid Circuit | 51
52 53 54 |
·
INF Code: 51 ·
Excess current is applied for 0.05 seconds or more. ·
INF Code: 52 ·
An open is detected for 0.05 seconds or more while the solenoid is OFF. ·
INF Code: 53 ·
An open is detected for 0.05 seconds or more while the solenoid is ON. ·
INF Code: 54 ·
A short to +B or voltage leak is detected for 0.05 seconds. |
·
INF Code: 51, 52, 54 ·
Brake booster with master cylinder assembly ·
INF Code: 53 ·
Supply voltage reduced ·
Brake booster with master cylinder assembly |
Electronically controlled brake system DTC |
| C1227/33 | SA3 Solenoid Circuit | 61
62 63 64 |
·
INF Code: 61 ·
Excess current is applied for 0.05 seconds or more. ·
INF Code: 62 ·
An open is detected for 0.05 seconds or more while the solenoid is OFF. ·
INF Code: 63 ·
An open is detected for 0.05 seconds or more while the solenoid is ON. ·
INF Code: 64 ·
A short to +B or voltage leak is detected for 0.05 seconds. |
·
INF Code: 61, 62, 64 ·
Brake booster with master cylinder assembly ·
INF Code: 63 ·
Supply voltage reduced ·
Brake booster with master cylinder assembly |
Electronically controlled brake system DTC |
| C1228/34 | STR Solenoid Circuit | 71
72 73 74 |
·
INF Code: 71 ·
Excess current is applied for 0.05 seconds or more. ·
INF Code: 72 ·
An open is detected for 0.05 seconds or more while the solenoid is OFF. ·
INF Code: 73 ·
An open is detected for 0.05 seconds or more while the solenoid is ON. ·
INF Code: 74 ·
A short to +B or voltage leak is detected for 0.05 seconds. |
·
INF Code: 71, 72, 74 ·
Brake booster with master cylinder assembly ·
INF Code: 73 ·
Supply voltage reduced ·
Brake booster with master cylinder assembly |
Electronically controlled brake system DTC |
| C1352/21 | FR Solenoid | 11
12 |
When the solenoid relay contact on, open or short in solenoid circuit continues for 0.05 seconds or more. | Brake booster with master cylinder assembly | Electronically controlled brake system DTC |
| C1353/23 | RR Solenoid | 15
16 |
When the solenoid relay contact on, open or short in solenoid circuit continues for 0.05 seconds or more. | Brake booster with master cylinder assembly | Electronically controlled brake system DTC |
| C1356/22 | FL Solenoid | 13
14 |
When the solenoid relay contact on, open or short in solenoid circuit continues for 0.05 seconds or more. | Brake booster with master cylinder assembly | Electronically controlled brake system DTC |
| C1357/24 | RL Solenoid | 17
18 |
When the solenoid relay contact on, open or short in solenoid circuit continues for 0.05 seconds or more. | Brake booster with master cylinder assembly | Electronically controlled brake system DTC |
When replacing the skid control ECU (brake booster with master cylinder assembly) or brake actuator (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION
Clear the DTCs.
Check if the same DTC is output.
If a DTC for undervoltage is output, first troubleshoot the power source system.
| Result | Proceed to |
|---|---|
| DTCs C1211/25, C1212/26, C1225/31, C1226/32, C1227/33, C1228/34, C1352/21, C1353/23, C1356/22 and C1357/24 are not output. | A |
| A DTC C1241/41 for undervoltage is output. | B |
| DTCs C1211/25, C1212/26, C1225/31, C1226/32, C1227/33, C1228/34, C1352/21, C1353/23, C1356/22 and/or C1357/24 are output. | C |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C