Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2012.02–2015.04
RM2040EQ _54 Brake _014708 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0074978 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1249/49  Open in Stop Light Switch Circuit  


DESCRIPTION

The skid control ECU receives the stop light switch assembly signal and detects the brake pedal operation status.

The skid control ECU has an open detection circuit, which stores this DTC if it detects an open in the stop light input line or ground line of the stop light circuit with the stop light switch assembly off (brake pedal not depressed).

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1249/49 Open in Stop Light Switch Circuit 231 When IG1 terminal voltage is 9.5 V or more, an open stop light switch circuit continues for 10 seconds or more.
·

Wire harness or connector

·

Stop light switch assembly

·

Skid control ECU (Brake booster with master cylinder assembly)


Electronically controlled brake system DTC

WIRING DIAGRAM

C244757E14
0.615,4.698 1.188,4.969 0.573,0.271 10 false STOP 5.979,2.813 6.656,3.219 0.677,0.406 10 false STP0 5.708,0.479 6.021,0.729 0.313,0.25 10 false 33 5.771,2.708 5.958,2.875 0.188,0.167 10 false 3 2.51,2.031 2.74,2.302 0.229,0.271 10 false 5 5.979,2.146 6.625,2.5 0.646,0.354 10 false STP2 1.51,4.552 3.073,4.906 1.563,0.354 10 false from Auxiliary Battery 0.958,0.99 1.292,1.156 0.333,0.167 10 false A33 2.365,3.229 3.927,3.677 1.563,0.448 10 false Stop Light Control Relay (STOP Relay) 0.948,1.156 2.104,1.51 1.156,0.354 10 false Stop Light Switch Assembly 5.031,4.802 5.5,5.167 0.469,0.365 10 false A28 5.031,4.969 7.156,5.333 2.125,0.365 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 3.656,2.677 3.865,2.969 0.208,0.292 10 false 1 4.135,4.417 5.573,4.688 1.438,0.271 10 false to Stop Light Circuit 5.781,2.063 5.979,2.229 0.198,0.167 10 false 6 5.979,0.563 6.406,0.719 0.427,0.156 10 false STP 0.5,4.438 0.708,4.708 0.208,0.271 10 false 2 0.958,4.438 1.208,4.698 0.25,0.26 10 false 1 2.51,2.677 2.75,2.958 0.24,0.281 10 false 2 3.656,2.031 3.844,2.198 0.188,0.167 10 false 3 2.969,1.625 3.24,1.917 0.271,0.292 10 false 4 2.115,0.469 2.396,0.792 0.281,0.323 10 false 1 0.813,0.469 1.115,0.75 0.302,0.281 10 false 2 0.917,4.208 2.063,4.417 1.146,0.208 10 false ECU-IG1 NO. 1 1.104,3.948 1.333,4.26 0.229,0.313 10 false 2 1.563,3.948 1.885,4.292 0.323,0.344 10 false 1 2.229,4.052 3.667,4.333 1.438,0.281 10 false from IG1 NO. 2 Relay

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed. ON
Brake pedal released. OFF



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH ASSEMBLY)

NG

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH ASSEMBLY)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Select the Data List on the intelligent tester.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Stop Light SW
50003 105 37

d.

Check that the stop light switch assembly display observed on the intelligent tester changes according to brake pedal operation.

OK:

The intelligent tester displays ON or OFF according to brake pedal operation.



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

4.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
3.RECONFIRM DTC
a.

Turn the power switch off.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the power switch on (READY).


d.

Depress the brake pedal several times to test the stop light circuit.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC C1249/49 is not output. A
DTC C1249/49 is output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE




A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
C249762C42
0.208,0.802 0.625,1.073 0.417,0.271 1.542,2.156 0.688,2.896 false 0.198,0.188 0.823,0.583 0.625,0.396 10 false *a 0.313,0.854 1,1.167 0.688,0.313 10 false A28 0.531,2.927 0.938,3.208 0.406,0.281 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Turn the power switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A28 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A28-33 (STP) - Body ground Stop light switch assembly ON (Brake pedal depressed) 11 to 14 V
A28-33 (STP) - Body ground Stop light switch assembly OFF (Brake pedal released) Below 1.5 V


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
C173882C09
0.365,0.979 0.833,1.302 0.469,0.323 0.333,0.25 0.552,0.406 0.219,0.156 10 false *a 0.469,1.073 0.896,1.365 0.427,0.292 10 false A33
*a Front view of wire harness connector (to Stop Light Switch Assembly)


Check that the STOP (7.5 A) fuse is normal.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A33 stop light switch assembly connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A33-2 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

6.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.
C239673C08
0.338,0.37 0.564,0.54 0.226,0.17 10 *a 1.941,1.855 2.415,1.068 false 1.659,1.855 1.184,1.068 false 2.401,0.851 2.571,1.021 0.17,0.17 10 1 1.077,0.851 1.233,1.021 0.156,0.17 10 2
*a Component without harness connected (Stop Light Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Switch pin free Below 1 Ω
1 - 2 Switch pin pushed in 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (SWITCH INPUT)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (SWITCH INPUT)
a.
C244747C06
0.249,0.2 0.433,0.356 0.184,0.156 10 *1 1.034,1.861 0.736,1.861 false 0.547,1.77 0.731,1.926 0.184,0.156 10 *2
*1 No. 2 Engine Room Relay Block
*2 Stop Light Control Relay (STOP Relay)


Reconnect the A33 stop light switch assembly connector.


b.

Remove the stop light control relay (STOP relay).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Stop light control relay (STOP relay) terminal 4 - Body ground Stop light switch assembly ON (Brake pedal depressed) 11 to 14 V
Stop light control relay (STOP relay) terminal 4 - Body ground Stop light switch assembly OFF (Brake pedal released) Below 1.5 V



Result:
Proceed to
OK
NG



OK

8.INSPECT STOP LIGHT CONTROL RELAY (STOP RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT STOP LIGHT CONTROL RELAY (STOP RELAY)
a.
C223784C12
2.719,1.438 2.719,0.885 2.719,0.885 2.76,0.885 false 2.448,1.927 2.448,1.656 2.448,1.656 2.01,1.656 false 2.281,2.313 2.281,2.844 2.281,2.844 2.229,2.844 false 2.573,2.313 2.573,3.083 2.573,3.083 2.531,3.083 false 2.833,2.313 2.833,3.083 2.833,3.083 2.875,3.083 false 0.281,0.25 0.531,0.448 0.25,0.198 10 false *1 1.896,1.573 2.021,1.74 0.125,0.167 10 false 5 2.906,3 3.031,3.167 0.125,0.167 10 false 1 2.125,2.76 2.25,2.927 0.125,0.167 10 false 2 2.802,0.802 2.927,0.969 0.125,0.167 10 false 3 2.417,3 2.542,3.167 0.125,0.167 10 false 4
*1 Stop Light Control Relay (STOP Relay)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 4 Voltage is not applied between terminals 1 and 2 Below 1 Ω
3 - 4 Voltage is applied between terminals 1 and 2 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

NG

REPLACE STOP LIGHT CONTROL RELAY (STOP RELAY)

9.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.

Install the stop light control relay (STOP relay).


b.
C249762C43
0.208,0.802 0.625,1.073 0.417,0.271 1.542,2.156 0.688,2.896 false 2.125,0.969 1.677,1.667 false 0.198,0.188 0.823,0.583 0.625,0.396 10 false *a 0.313,0.854 1,1.167 0.688,0.313 10 false A28 0.542,2.938 0.948,3.219 0.406,0.281 10 false STP 2.031,0.792 2.615,1.083 0.583,0.292 10 false STP2
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A28 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A28-6 (STP2) - Body ground Stop light switch assembly ON (Brake pedal depressed) 11 to 14 V
A28-6 (STP2) - Body ground Stop light switch assembly OFF (Brake pedal released) Below 1.5 V
A28-33 (STP) - Body ground Stop light switch assembly ON (Brake pedal depressed) 11 to 14 V
A28-33 (STP) - Body ground Stop light switch assembly OFF (Brake pedal released) Below 1.5 V



Result:
Proceed to
OK
NG



OK

10.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

10.RECONFIRM DTC
a.

Reconnect the A28 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the power switch on (READY).


d.

Depress the brake pedal several times to test the stop light circuit.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC C1249/49 is not output. A
DTC C1249/49 is output. B


HINT:
·

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE

·

If the lighting system is normal but the DTC is still output, replace the skid control ECU (brake booster with master cylinder assembly).

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER>REMOVAL





A

B

INSPECT LIGHTING SYSTEM (STOP LIGHT CIRCUIT)