The main body ECU (multiplex network body ECU) receives seat memory switch signals from the outer mirror control ECU assembly RH via CAN communication. If the seat memory SET switch is being pressed when one of the M1 or M2 switches is pressed, or if one of the M1 or M2 switches is pressed within 3 seconds of pressing the seat memory SET switch, the main body ECU (multiplex network body ECU) sends a memory request signal to the position control ECU and switch assembly. After receiving the request signal, the position control ECU and switch assembly memorizes the location data of each motor.
The seat position will not be recorded if the SET switch and 2 of the seat memory switches are pressed simultaneously.
If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.
The front power seat control system (w/ Memory) uses the CAN communication system. First, confirm that there is no malfunction in the communication system by checking communication function of the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>HOW TO PROCEED WITH TROUBLESHOOTING).
Check that each function of the power seat operates normally by using the power seat switch.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
Each function of the power seat operates normally using the power seat switch.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Mirror R / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Seat Memory Switch1 | M1 switch | ON or OFF | ON: M1 switch on
OFF: M1 switch off |
- |
| Seat Memory Switch2 | M2 switch | ON or OFF | ON: M2 switch on
OFF: M2 switch off |
- |
| Seat Memory Set SW | SET switch | ON or OFF | ON: SET switch on
OFF: SET switch off |
- |
| Tester Display |
|---|
| Seat Memory Switch1 |
| Seat Memory Switch2 |
| Seat Memory Set SW |
ON or OFF is displayed on the intelligent tester according to the table above.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Driver Seat / Active Test.
Perform the Active Test according to the display on the intelligent tester.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Buzzer | Buzzer operation | OFF/ON | - |
| Tester Display |
|---|
| Buzzer |
Buzzer sounds normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the outer mirror control ECU assembly RH.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR CONTROL ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Store a seat position in memory and check that the buzzer sounds to indicate that a position has been stored.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
The seat position will not be recorded if the SET switch and 2 of the seat memory switches are pressed simultaneously.
If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.
Seat position memory function operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the position control ECU and switch assembly.
Click hereVehicle Interior>SEAT>POWER SEAT SWITCH(w/ Seat Position Memory System)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Store a seat position in memory and check that the buzzer sounds to indicate that a position has been stored.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
The seat position will not be recorded if the SET switch and 2 of the seat memory switches are pressed simultaneously.
If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.
Seat position memory function operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | M1 Switch |
| *2 | M2 Switch |
| *3 | SET Switch |
| *a | Component without harness connected
(Seat Memory Switch) |
Remove the seat memory switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 - 1 | SET switch is pressed | Below 1 Ω |
| 4 - 1 | M1 switch is pressed | Below 1 Ω |
| 3 - 1 | M2 switch is pressed | Below 1 Ω |
| 2 - 1 | SET switch is not pressed | 10 kΩ or higher |
| 4 - 1 | M1 switch is not pressed | 10 kΩ or higher |
| 3 - 1 | M2 switch is not pressed | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the J13 outer mirror control ECU assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J16-2 (MRY) - J13-1 (MM) | Always | Below 1 Ω |
| J16-4 (M1) - J13-2 (M1) | Always | Below 1 Ω |
| J16-3 (M2) - J13-3 (M2) | Always | Below 1 Ω |
| J16-1 (E) - J13-13 (MSWE) | Always | Below 1 Ω |
| J13-7 (GND) - Body ground | Always | Below 1 Ω |
| J13-1 (MM) - Body ground | Always | 10 kΩ or higher |
| J13-2 (M1) - Body ground | Always | 10 kΩ or higher |
| J13-3 (M2) - Body ground | Always | 10 kΩ or higher |
| J13-13 (MSWE) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG