Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM
RM2040EQ _58 Vehicle Interior _014722 DOOR LOCK _0075051 POWER DOOR LOCK CONTROL SYSTEM C

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  B1243  GSW Terminal Circuit Malfunction  


DESCRIPTION

If the collision door lock release function does not operate normally, or an open or short in the GSW input circuit of the main body ECU (multiplex network body ECU) is detected, DTC B1243 will be stored.

HINT:

If DTC B1243 is stored, the speed-sensitive automatic door lock function, shift-linked automatic door lock function, and collision door lock release function will be prohibited.


DTC No. Detection Item DTC Detection Condition Trouble Area
B1243 GSW Terminal Circuit Malfunction A malfunction occurs in the GSW input circuit of the main body ECU (multiplex network body ECU).
·

Main body ECU (multiplex network body ECU)

·

Airbag sensor assembly

·

Wire harness or connector



WIRING DIAGRAM

B290667E01
0.458,2.104 2.031,2.313 1.573,0.208 10 false Airbag Sensor Assembly 1.219,1.042 1.708,1.385 0.49,0.344 10 false GSW 1.677,0.958 1.885,1.135 0.208,0.177 10 false 18 0.458,1.938 0.719,2.115 0.26,0.177 10 false I47 4.677,0.854 4.917,1.083 0.24,0.229 10 false 45 4.667,1.031 4.917,1.219 0.25,0.188 10 false 3A 2.896,1.531 5.552,1.74 2.656,0.208 10 false Instrument Panel Junction Block Assembly 5.417,0.958 5.625,1.219 0.208,0.26 10 false 24 5.646,1.042 6.063,1.271 0.417,0.229 10 false GSW 5.208,2.01 6.885,2.521 1.677,0.51 10 false Main Body ECU (Multiplex Network Body ECU) 5.208,1.854 5.479,2.063 0.271,0.208 10 false MB

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK DTC OUTPUT
a.

Clear the DTCs.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

b.

Recheck for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
OK:

DTC B1243 is not output.



Result:
Result
OK
NG



OK

NG

2.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (GSW VOLTAGE)
2.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (GSW VOLTAGE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



b.

Disconnect the I47 airbag sensor assembly connector.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.
B275903C05
1.542,0.938 2.052,1.219 0.51,0.281 2.146,1.948 2.146,2.552 false 1.719,1 2.063,1.271 0.344,0.271 10 false I47 2,2.604 2.615,2.917 0.615,0.313 10 false GSW 0.219,0.167 0.625,0.594 0.406,0.427 10 false *a
*a Front view of wire harness connector
(to Airbag Sensor Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I47-18 (GSW) - Body ground power switch on (IG) 2.8 to 4.3 V


NOTICE:

Turning the power switch on (IG) with the airbag sensor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



Result:
Result
OK
NG



OK

3.REPLACE AIRBAG SENSOR ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (AIRBAG SENSOR ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
3.REPLACE AIRBAG SENSOR ASSEMBLY
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




Result:
Proceed to
NEXT



NEXT

4.CHECK DTC OUTPUT
4.CHECK DTC OUTPUT
a.

Clear the DTCs.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

b.

Recheck for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
OK:

DTC B1243 is not output.



Result:
Result
OK
NG



OK

END (AIRBAG SENSOR ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

5.CHECK HARNESS AND CONNECTOR (AIRBAG SENSOR ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



b.

Disconnect the I47 airbag sensor assembly connector.


c.

Disconnect the 3A instrument panel junction block assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I47-18 (GSW) - 3A-45 Always Below 1 Ω
3A-45 - Body ground Always 10 kΩ or higher



Result:
Result
OK
NG



OK

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU).

B217444C23
1.854,1.156 2.198,1.365 0.344,0.208 5.594,0.969 5.938,1.177 0.344,0.208 2.927,1.74 2.927,2.094 false 0.229,0.135 0.781,0.74 0.552,0.604 10 false *a 1.938,1.177 2.281,1.406 0.344,0.229 10 false MB 5.698,0.99 6.031,1.344 0.333,0.354 10 false 3A 2.792,2.125 3.323,2.396 0.531,0.271 10 false GSW
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MB-24 (GSW) - 3A-45 Always Below 1 Ω



Result:
Result
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY