Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM
RM2040EQ _58 Vehicle Interior _014722 DOOR LOCK _0075051 POWER DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  All Doors LOCK/UNLOCK Functions do not Operate Via Door Control Switch or Door Key Cylinder  


DESCRIPTION

The main body ECU (multiplex network body ECU) receives switch signals from the door control switch (power window regulator master switch assembly), and driver door key cylinder switch signals from the front door lock with motor assembly RH. The main body ECU (multiplex network body ECU) activates the door lock motor on each door according to these signals.

WIRING DIAGRAM

B294404
5.479,4.979 7.156,5.385 1.677,0.406 10 false Main Body ECU (Multiplex Network Body ECU) 0.771,2.083 3.635,2.5 2.865,0.417 10 false Door Key Lock and Unlock Switch (Front Door Lock with Motor Assembly RH) 0.771,4.417 3.021,4.854 2.25,0.438 10 false Door Control Switch (Power Window Regulator Master Switch Assembly) 1.26,1.344 1.479,1.646 0.219,0.302 10 false 8 2.229,1.615 2.49,1.948 0.26,0.333 10 false 5 2.229,1.052 2.531,1.448 0.302,0.396 10 false 6 1.26,3.594 1.479,3.917 0.219,0.323 10 false 9 2.229,3.302 2.438,3.604 0.208,0.302 10 false 8 2.229,3.854 2.458,4.156 0.229,0.302 10 false 2 5.719,0.938 6.031,1.219 0.313,0.281 10 false 11 5.729,1.5 6.042,1.844 0.313,0.344 10 false 24 5.771,3.76 5.938,3.99 0.167,0.229 10 false 9 5.729,3.198 6.031,3.458 0.302,0.26 10 false 10 1.948,3.302 2.302,3.563 0.354,0.26 10 false UL 2.031,4.042 2.292,4.292 0.26,0.25 10 false L 1.417,3.594 1.698,3.938 0.281,0.344 10 false E 1.958,1.813 2.302,2.083 0.344,0.271 10 false UL 2.042,1.052 2.344,1.344 0.302,0.292 10 false L 1.427,1.344 1.667,1.583 0.24,0.24 10 false E 6.042,1.167 6.406,1.521 0.365,0.354 10 false L2 6.042,1.719 6.49,2.042 0.448,0.323 10 false UL3 6.042,3.969 6.344,4.271 0.302,0.302 10 false L1 6.042,3.406 6.49,3.844 0.448,0.438 10 false UL1 5.719,3.958 5.969,4.26 0.25,0.302 10 false I13 5.719,3.396 6.01,3.656 0.292,0.26 10 false I13 5.719,1.698 6.073,1.948 0.354,0.25 10 false I13 5.719,1.135 6.167,1.646 0.448,0.51 10 false I13 0.781,4.24 1.135,4.51 0.354,0.271 10 false J10 0.781,1.906 1.156,2.302 0.375,0.396 10 false J1

PROCEDURE

1.CHECK DOOR LOCK OPERATION

Result:
Result Proceed to
All doors cannot be locked through door control switch (power window regulator switch assembly) A
All doors cannot be locked through door key cylinder B



A

2.READ VALUE USING INTELLIGENT TESTER (DOOR CONTROL SWITCH (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY))

B

5.READ VALUE USING INTELLIGENT TESTER (DOOR KEY-LINKED LOCK AND UNLOCK SWITCH (FRONT DOOR LOCK WITH MOTOR ASSEMBLY (DRIVER DOOR)))
2.READ VALUE USING INTELLIGENT TESTER (DOOR CONTROL SWITCH (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY))
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Door Lock SW-Lock Door control switch (power window regulator master switch assembly) lock signal ON or OFF ON: Lock side of door control switch (power window regulator master switch assembly) pushed
OFF: Lock side of door control switch (power window regulator master switch assembly) not pushed
-
Door Lock SW-Unlock Door control switch (power window regulator master switch assembly) unlock signal ON or OFF ON: Unlock side of door control switch (power window regulator master switch assembly) pushed
OFF: Unlock side of door control switch (power window regulator master switch assembly) not pushed
-
Body Electrical > Main Body > Data List
Tester Display
Door Lock SW-Lock
Door Lock SW-Unlock
50003 123 17,18
OK:

The intelligent tester indicates ON or OFF according to the switch operation shown in the table above.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

3.INSPECT DOOR CONTROL SWITCH (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY)
3.INSPECT DOOR CONTROL SWITCH (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY)
a.
B295736
0.148,0.115 0.323,0.271 0.175,0.156 10 *a 0.469,3.214 0.469,1.959 0.469,1.959 0.787,1.959 false 0.604,3.227 0.604,2.482 0.604,2.482 0.784,2.482 false 1.448,3.228 1.448,2.483 1.448,2.483 1.689,2.483 false 0.823,2.406 1.028,2.549 0.205,0.142 10 UL 0.832,1.873 0.946,2.016 0.115,0.142 10 E 1.734,2.398 1.836,2.54 0.102,0.142 10 L
*a Component without harness connected
(Door Control Switch (Power Window Regulator Master Switch Assembly))


Remove the door control switch (power window regulator master switch assembly).

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (L) - 9 (E) Lock switch pushed Below 1 Ω
2 (L) - 9 (E) off 10 kΩ or higher
8 (UL) - 9 (E) Unlock switch pushed Below 1 Ω
8 (UL) - 9 (E) off 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the I13 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J10-2 (L) - I13-9 (L1) Always Below 1 Ω
J10-8 (UL) - I13-10 (UL1) Always Below 1 Ω
J10-9 (E) - Body ground Always Below 1 Ω
J10-2 (L) - Body ground Always 10 kΩ or higher
J10-8 (UL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.READ VALUE USING INTELLIGENT TESTER (DOOR KEY-LINKED LOCK AND UNLOCK SWITCH (FRONT DOOR LOCK WITH MOTOR ASSEMBLY (DRIVER DOOR)))
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Door Key SW-Lock Driver door key-linked lock/unlock switch lock signal ON or OFF ON: Driver door key cylinder turned to lock position
OFF: Driver door key cylinder not turned to lock position
-
D Door Key SW-UL Driver door key-linked lock/unlock switch unlock signal ON or OFF ON: Driver door key cylinder turned to unlock position
OFF: Driver door key cylinder not turned to unlock position
-
Body Electrical > Main Body > Data List
Tester Display
Door Key SW-Lock
D Door Key SW-UL
50003 123 19,21
OK:

The intelligent tester indicates ON or OFF according to the key cylinder operation shown in the table.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

6.INSPECT FRONT DOOR LOCK WITH MOTOR ASSEMBLY RH
6.INSPECT FRONT DOOR LOCK WITH MOTOR ASSEMBLY RH
a.

Remove the front door lock with motor assembly RH.

Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL


b.
B284859
0.748,3.424 0.748,4.442 0.748,4.442 0.903,4.442 false 1.057,3.424 1.057,4.133 1.057,4.133 1.212,4.133 false 1.212,3.424 1.212,3.823 1.212,3.823 1.367,3.823 false 0.955,4.35 1.079,4.507 0.124,0.156 10 E 1.264,4.041 1.374,4.197 0.11,0.156 10 L 1.402,3.732 1.614,3.888 0.212,0.156 10 UL 0.084,0.033 0.233,0.204 0.149,0.17 10 *a 0.6,1.615 0.749,1.785 0.149,0.17 10 *b 0.342,0.515 0.491,0.685 0.149,0.17 10 *c
*a Component without harness connected
(Front Door Lock with Motor Assembly RH)
*b Lock
*c Unlock


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (L) - 8 (E) Held to lock side Below 1 Ω
6 (L) - 8 (E) Neutral or held to unlock side 10 kΩ or higher
5 (UL) - 8 (E) Held to unlock side Below 1 Ω
5 (UL) - 8 (E) Neutral or held to lock side 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK WITH MOTOR ASSEMBLY RH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPLACE FRONT DOOR LOCK WITH MOTOR ASSEMBLY RH

7.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK WITH MOTOR ASSEMBLY RH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the I13 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J1-6 (L) - I13-11 (L2) Always Below 1 Ω
J1-5 (UL) - I13-24 (UL3) Always Below 1 Ω
J1-8 (E) - Body ground Always Below 1 Ω
I13-11 (L2) - Body ground Always 10 kΩ or higher
I13-24 (UL3) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR