Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM2040EQ _57 Power Source / Network _014721 NETWORKING _0075041 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2321  Driver Side Door ECU Communication Stop  


DESCRIPTION

This DTC is stored when LIN communication between the power window regulator motor assembly (for driver side) and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2321 Driver Side Door ECU Communication Stop No communication between power window regulator motor assembly (for driver side) and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Power window regulator motor assembly (for driver side)

·

Main body ECU (multiplex network body ECU)

·

Wire harness or connector

·

Instrument Panel junction block assembly

·

DOOR No. 2 fuse



WIRING DIAGRAM

B274860
0.802,2.406 2.875,2.771 2.073,0.365 10 false : LIN Communication Line 0.406,1.885 3.479,2.302 3.073,0.417 10 false Instrument Panel Junction Block Assembly 1.313,0.521 1.885,0.813 0.573,0.292 10 false LIN2 4.698,0.521 5.271,1.052 0.573,0.531 10 false LIN 0.385,1.729 0.927,2.083 0.542,0.354 10 false 3B 4.51,1.906 6.479,2.677 1.969,0.771 10 false Power Window Regulator Motor Assembly (for Driver Side) 4.5,1.74 5.396,2.042 0.896,0.302 10 false J9 5.448,1.188 5.927,1.552 0.479,0.365 10 false E 5.448,0.51 5.719,1.063 0.271,0.552 10 false B 6,0.677 6.958,1.083 0.958,0.406 10 false DOOR No. 2 5.646,0.406 6.01,0.75 0.365,0.344 10 false 2 5.646,1.073 6.031,1.385 0.385,0.313 10 false 1 4.51,0.365 4.948,0.74 0.438,0.375 10 false 9 2.625,0.365 3.292,0.833 0.667,0.469 10 false 30 1.708,0.365 2.313,0.75 0.604,0.385 10 false 16 0.854,0.844 1.333,1.115 0.479,0.271 10 false MB 2.25,0.365 2.823,0.656 0.573,0.292 10 false LIN2 0.854,0.99 2.51,1.51 1.656,0.521 10 false Main Body ECU (Multiplex Network Body ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When the power window regulator motor assembly (for driver side) is replaced or removed and reinstalled, it requires initialization (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).

·

When using the intelligent tester to troubleshoot with the power switch off:

Connect the intelligent tester to the DLC3, and turn the courtesy switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY)
a.

Disconnect the 3B instrument panel junction block assembly connector.


b.

Disconnect the J9 power window regulator motor assembly (for driver side) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3B-30 (LIN2) - J9-9 (LIN) Always Below 1 Ω
3B-30 (LIN2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

B281983
1.813,0.917 2.177,1.188 0.365,0.271 5.49,0.844 5.854,1.115 0.365,0.271 1.802,2.188 2.052,1.74 false 5.615,2.271 5.865,1.833 false 1.896,0.969 2.208,1.167 0.313,0.198 10 MB 5.604,0.896 5.917,1.094 0.313,0.198 10 3B 0.406,0.375 0.719,0.573 0.313,0.198 10 *a 4.792,0.458 5.104,0.656 0.313,0.198 10 *b 1.667,2.219 2.281,2.417 0.615,0.198 10 LIN2 5.448,2.302 6.063,2.5 0.615,0.198 10 LIN2
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
*b Component without harness connected
(Instrument Panel Junction Block Assembly)



b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

HINT:

This inspection is to check the LIN line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).


Standard Resistance:
Tester Connection Condition Specified Condition
3B-30 (LIN2) - MB-16 (LIN2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY - AUXILIARY BATTERY, BODY GROUND)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY - AUXILIARY BATTERY, BODY GROUND)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
J9-2 (B) - Body ground Power switch off 11 to 14 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J9-1 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for DRIVER SIDE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for DRIVER SIDE)
a.

Replace the power window regulator motor assembly (for driver side).

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR(for Front Door)>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK DTC OUTPUT
5.CHECK DTC OUTPUT
a.

Clear the DTC.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

b.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
OK:

DTC B2321 is not output.



Result:
Proceed to
OK
NG



OK

END (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for DRIVER SIDE) WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)