The main body ECU (multiplex network body ECU) monitors communication between all the ECUs connected to the door bus lines. When the main body ECU (multiplex network body ECU) detects errors in communication with all the ECUs connected to the door bus lines at 2.6-second intervals and 3 times in a row, DTC B2325 will be stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2325 | LIN Communication Bus Malfunction | Main body ECU (multiplex network body ECU) detects errors in communication with the ECUs connected to the door bus lines 3 times in a row. | ·
Power window regulator motor assembly (for driver side) ·
Sliding roof ECU (sliding roof drive gear sub-assembly)* ·
Main body ECU (multiplex network body ECU) ·
Instrument panel junction block assembly ·
Wire harness or connector |
*: w/ Sliding Roof System
When the sliding roof ECU (sliding roof drive gear sub-assembly) is replaced or removed and reinstalled, it requires initialization (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION).*
When the power window regulator motor assembly (for driver side) is replaced or removed and reinstalled, it requires initialization (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).
When using the intelligent tester to troubleshoot with the power switch off:
Connect the intelligent tester to the DLC3, and turn the courtesy switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.
*: w/ Sliding Roof System
Remove the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
*b | Component without harness connected
(Instrument Panel Junction Block Assembly) |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Measure the resistance according to the value(s) in the table below.
This inspection is to check the LIN line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3B-30 (LIN2) - MB-16 (LIN2) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the J9 power window regulator motor assembly (for driver side) connector.
Disconnect the S4 sliding roof ECU (sliding roof drive gear sub-assembly) connector.*
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3B-30 (LIN2) - J9-9 (LIN) | Always | Below 1 Ω |
| 3B-30 (LIN2) - S4-11 (MPX1)* | Always | Below 1 Ω |
| J9-9 (LIN) - Body ground | Always | 10 kΩ or higher |
| S4-11 (MPX1)* - Body ground | Always | 10 kΩ or higher |
*: w/ Sliding Roof System
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the 3B instrument panel junction block assembly connector.
Reconnect the S4 sliding roof ECU (sliding roof drive gear sub-assembly) connector.*
*: w/ Sliding Roof System
Clear the DTC.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR
After 10 seconds have elapsed, check if the trouble occurs again.
Check for DTCs again.
| Result | Proceed to |
|---|---|
| DTC B2325 is output (w/ Sliding Roof System) | A |
| DTC B2325 is output (w/o Sliding Roof System) | B |
| DTC B2325 is not output | C |
A
B
C
Reconnect the J9 power window regulator motor assembly (for driver side) connector.
Disconnect the S4 sliding roof ECU (sliding roof drive gear sub-assembly) connector.
Clear the DTC.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR
After 10 seconds have elapsed, check if the trouble occurs again.
Check for DTCs again.
| Result | Proceed to |
|---|---|
| DTC B2325 is output | A |
| DTC B2325 is not output | B |
A
B