Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › 2012.02–2015.04
RM2040EQ _56 Audio / Visual / Telematics _014718 PARK ASSIST / MONITORING _0075026 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB0  Short to +B in Outer Mirror Indicator(Master)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor RH detects a +B short in the outer rear view mirror indicator RH.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AB0 Short to +B in Outer Mirror Indicator(Master)
Both of the following conditions are met:
·

Blind spot monitor main switch (warning canceling switch assembly) is on.


·

The blind spot monitor sensor is not sending voltage to the indicator but the indicator receives voltage above a specified level for a specified period of time.


·

Outer rear view mirror RH

·

Mirror sub-assembly RH

·

Wire harness or connector

·

Blind spot monitor sensor RH

·

Outer mirror control ECU assembly RH



WIRING DIAGRAM

E233743E39
1.573,1.271 1.708,1.427 0.135,0.156 10 false 1 2.979,1.156 3.115,1.313 0.135,0.156 10 false 7 5.823,1.26 5.948,1.417 0.125,0.156 10 false 6 3.281,1.375 3.688,1.531 0.406,0.156 10 false BDIR 5.99,1.354 6.396,1.51 0.406,0.156 10 false OMIR 3.281,1.833 3.646,1.99 0.365,0.156 10 false HTR- 0.219,2.156 0.594,2.313 0.375,0.156 10 false IND1 5.885,3.396 6.333,3.552 0.448,0.156 10 false O28 1.385,1.365 1.521,1.521 0.135,0.156 10 false + 1.385,1.844 1.604,2 0.219,0.156 10 false - 1.583,1.74 1.719,1.896 0.135,0.156 10 false 2 2.927,1.625 3.125,1.781 0.198,0.156 10 false 12 0.219,2.323 2.354,2.49 2.135,0.167 10 false Outer Rear View Mirror RH 0.469,3.406 2.208,3.667 1.74,0.26 10 false Mirror Sub-assembly RH 5.885,3.573 7.083,3.885 1.198,0.313 10 false Blind Spot Monitor Sensor RH 0.198,2.615 2.281,2.927 2.083,0.313 10 false (Outer Rear View Mirror Indicator RH) 2.896,1.354 3.333,1.594 0.438,0.24 10 false z17 2.896,1.823 3.302,2.073 0.406,0.25 10 false z17 3.177,3.396 4.729,3.76 1.552,0.365 10 false Outer Mirror Control ECU Assembly RH 4.01,1.354 4.417,1.51 0.406,0.156 10 false BDSR 4.073,1.823 4.438,1.979 0.365,0.156 10 false GND 4.594,1.146 4.781,1.302 0.188,0.156 10 false 10 4.646,1.625 4.781,1.781 0.135,0.156 10 false 7 4.552,1.344 4.813,1.5 0.26,0.156 10 false J13 4.552,1.823 4.885,1.979 0.333,0.156 10 false J13

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor main switch (warning canceling switch assembly) is on.


PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Master > Clear DTCs
50002 313

b.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Blind Spot Monitor Master > Trouble Codes
50001 313
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT OUTER REAR VIEW MIRROR RH (OUTER REAR VIEW MIRROR INDICATOR RH)
2.INSPECT OUTER REAR VIEW MIRROR RH (OUTER REAR VIEW MIRROR INDICATOR RH)
a.

Disconnect connector O28 from the blind spot monitor sensor RH.


b.
C240531C13
0.127,0.058 0.34,0.256 0.213,0.198 10 *a 1.023,2.432 1.465,2.619 0.442,0.187 10 OMIR 1.69,1.931 1.692,2.521 1.692,2.521 1.501,2.521 false 0.417,1.604 0.933,1.914 0.516,0.309 0.52,1.672 0.815,1.854 0.296,0.182 10 O28
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
O28-6 (OMIR) - Body ground Power switch on (IG) Below 1 V



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR RH - BLIND SPOT MONITOR SENSOR RH)
3.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR RH - BLIND SPOT MONITOR SENSOR RH)
a.

Disconnect connector IND1 from the outer rear view mirror RH.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
O28-6 (OMIR) - Body ground Power switch on (IG) Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE OUTER REAR VIEW MIRROR RH (OUTER REAR VIEW MIRROR INDICATOR RH)

NG

4.CHECK HARNESS AND CONNECTOR (MIRROR SUB-ASSEMBLY RH - BLIND SPOT MONITOR SENSOR RH)
4.CHECK HARNESS AND CONNECTOR (MIRROR SUB-ASSEMBLY RH - BLIND SPOT MONITOR SENSOR RH)
a.

Disconnect connector z17 from the outer mirror control ECU assembly RH.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
O28-6 (OMIR) - Body ground Power switch on (IG) Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE MIRROR SUB-ASSEMBLY RH

NG

5.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY RH - BLIND SPOT MONITOR SENSOR RH)
5.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY RH - BLIND SPOT MONITOR SENSOR RH)
a.

Disconnect connector J13 from the outer mirror control ECU assembly RH.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
O28-6 (OMIR) - Body ground Power switch on (IG) Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR