Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › 2012.02–2015.04
RM2040EQ _56 Audio / Visual / Telematics _014718 PARK ASSIST / MONITORING _0075026 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB1  Short to +B in Outer Mirror Indicator(Slave)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH detects a +B short in the outer rear view mirror indicator LH.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AB1 Short to +B in Outer Mirror Indicator(Slave)
Both of the following conditions are met:
·

Blind spot monitor main switch (warning canceling switch assembly) is on.


·

The blind spot monitor sensor is not sending voltage to the indicator but the indicator receives voltage above a specified level for a specified period of time.


·

Outer rear view mirror LH

·

Mirror sub-assembly LH

·

Wire harness or connector

·

Blind spot monitor sensor LH

·

Outer mirror control ECU assembly LH



WIRING DIAGRAM

E233743E40
1.573,1.271 1.708,1.427 0.135,0.156 10 false 1 2.979,1.156 3.115,1.313 0.135,0.156 10 false 7 5.823,1.26 5.948,1.417 0.125,0.156 10 false 6 3.281,1.375 3.688,1.531 0.406,0.156 10 false BDIL 5.99,1.354 6.396,1.51 0.406,0.156 10 false OMIL 3.281,1.833 3.646,1.99 0.365,0.156 10 false HTR- 0.219,2.156 0.594,2.313 0.375,0.156 10 false IND2 5.885,3.396 6.333,3.552 0.448,0.156 10 false T10 1.385,1.365 1.521,1.521 0.135,0.156 10 false + 1.385,1.844 1.521,2 0.135,0.156 10 false - 1.583,1.74 1.719,1.896 0.135,0.156 10 false 2 2.927,1.625 3.125,1.781 0.198,0.156 10 false 12 0.219,2.323 2.354,2.49 2.135,0.167 10 false Outer Rear View Mirror LH 0.531,3.396 2.135,3.75 1.604,0.354 10 false Mirror Sub-assembly LH 5.885,3.573 7.083,3.885 1.198,0.313 10 false Blind Spot Monitor Sensor LH 0.198,2.615 2.281,2.927 2.083,0.313 10 false (Outer Rear View Mirror Indicator LH) 2.885,1.354 3.323,1.542 0.438,0.188 10 false z16 2.896,1.823 3.417,2.135 0.521,0.313 10 false z16 3.177,3.396 4.75,3.76 1.573,0.365 10 false Outer Mirror Control ECU Assembly LH 4.01,1.354 4.656,1.75 0.646,0.396 10 false BDSL 4.073,1.823 4.438,1.979 0.365,0.156 10 false GND 4.594,1.146 4.781,1.302 0.188,0.156 10 false 10 4.646,1.625 4.781,1.781 0.135,0.156 10 false 7 4.542,1.354 4.823,1.51 0.281,0.156 10 false K12 4.542,1.823 4.875,1.979 0.333,0.156 10 false K12

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor main switch (warning canceling switch assembly) is on.


PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Slave > Clear DTCs
50002 314

b.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT OUTER REAR VIEW MIRROR LH (OUTER REAR VIEW MIRROR INDICATOR LH)
2.INSPECT OUTER REAR VIEW MIRROR LH (OUTER REAR VIEW MIRROR INDICATOR LH)
a.

Disconnect connector T10 from the blind spot monitor sensor LH.


b.
C240531C19
0.417,1.604 0.938,1.917 0.521,0.313 1.688,1.927 1.688,2.521 1.688,2.521 1.5,2.521 false 0.125,0.063 0.417,0.375 0.292,0.313 10 false *a 1.01,2.438 1.646,2.719 0.635,0.281 10 false OMIL 0.583,1.677 1.083,1.979 0.5,0.302 10 false T10
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
T10-6 (OMIL) - Body ground Power switch on (IG) Below 1 V



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR LH - BLIND SPOT MONITOR SENSOR LH)
3.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR LH - BLIND SPOT MONITOR SENSOR LH)
a.

Disconnect connector IND2 from the outer rear view mirror LH.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
T10-6 (OMIL) - Body ground Power switch on (IG) Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE OUTER REAR VIEW MIRROR LH (OUTER REAR VIEW MIRROR INDICATOR LH)

NG

4.CHECK HARNESS AND CONNECTOR (MIRROR SUB-ASSEMBLY LH - BLIND SPOT MONITOR SENSOR LH)
4.CHECK HARNESS AND CONNECTOR (MIRROR SUB-ASSEMBLY LH - BLIND SPOT MONITOR SENSOR LH)
a.

Disconnect connector z16 from the outer mirror control ECU assembly LH.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
T10-6 (OMIL) - Body ground Power switch on (IG) Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE MIRROR SUB-ASSEMBLY LH

NG

5.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY LH - BLIND SPOT MONITOR SENSOR LH)
5.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY LH - BLIND SPOT MONITOR SENSOR LH)
a.

Disconnect connector K12 from the outer mirror control ECU assembly LH.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
T10-6 (OMIL) - Body ground Power switch on (IG) Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR