Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › 2012.02–2015.04
RM2040EQ _56 Audio / Visual / Telematics _014718 PARK ASSIST / MONITORING _0075026 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB2  Short to GND in Outer Mirror Indicator(Master)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor RH detects a ground short in the outer rear view mirror indicator RH.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AB2 Short to GND in Outer Mirror Indicator(Master)
Both of the following conditions are met:
·

Blind spot monitor main switch (warning canceling switch assembly) is on.


·

The current that is sent from the blind spot monitor sensor to the indicator is above a specified level for a specified period of time.


·

Outer rear view mirror RH

·

Mirror sub-assembly RH

·

Wire harness or connector

·

Blind spot monitor sensor RH

·

Outer mirror control ECU assembly RH



WIRING DIAGRAM

E233743E39
1.573,1.271 1.708,1.427 0.135,0.156 10 false 1 2.979,1.156 3.115,1.313 0.135,0.156 10 false 7 5.823,1.26 5.948,1.417 0.125,0.156 10 false 6 3.281,1.375 3.688,1.531 0.406,0.156 10 false BDIR 5.99,1.354 6.396,1.51 0.406,0.156 10 false OMIR 3.281,1.833 3.646,1.99 0.365,0.156 10 false HTR- 0.219,2.156 0.594,2.313 0.375,0.156 10 false IND1 5.885,3.396 6.333,3.552 0.448,0.156 10 false O28 1.385,1.365 1.521,1.521 0.135,0.156 10 false + 1.385,1.844 1.604,2 0.219,0.156 10 false - 1.583,1.74 1.719,1.896 0.135,0.156 10 false 2 2.927,1.625 3.125,1.781 0.198,0.156 10 false 12 0.219,2.323 2.354,2.49 2.135,0.167 10 false Outer Rear View Mirror RH 0.469,3.406 2.208,3.667 1.74,0.26 10 false Mirror Sub-assembly RH 5.885,3.573 7.083,3.885 1.198,0.313 10 false Blind Spot Monitor Sensor RH 0.198,2.615 2.281,2.927 2.083,0.313 10 false (Outer Rear View Mirror Indicator RH) 2.896,1.354 3.333,1.594 0.438,0.24 10 false z17 2.896,1.823 3.302,2.073 0.406,0.25 10 false z17 3.177,3.396 4.729,3.76 1.552,0.365 10 false Outer Mirror Control ECU Assembly RH 4.01,1.354 4.417,1.51 0.406,0.156 10 false BDSR 4.073,1.823 4.438,1.979 0.365,0.156 10 false GND 4.594,1.146 4.781,1.302 0.188,0.156 10 false 10 4.646,1.625 4.781,1.781 0.135,0.156 10 false 7 4.552,1.344 4.813,1.5 0.26,0.156 10 false J13 4.552,1.823 4.885,1.979 0.333,0.156 10 false J13

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor main switch (warning canceling switch assembly) is on.


PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Master > Clear DTCs
50002 313

b.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Blind Spot Monitor Master > Trouble Codes
50001 313
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY RH - BLIND SPOT MONITOR SENSOR RH)
2.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY RH - BLIND SPOT MONITOR SENSOR RH)
a.

Disconnect connector O28 from the blind spot monitor sensor RH.


b.

Disconnect connector J13 from the outer mirror control ECU assembly RH.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Always
J13-10 (BDSR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT OUTER REAR VIEW MIRROR RH (OUTER REAR VIEW MIRROR INDICATOR RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT OUTER REAR VIEW MIRROR RH (OUTER REAR VIEW MIRROR INDICATOR RH)
a.

Disconnect connector IND1 from the outer rear view mirror RH.


b.
E233737C08
1.583,1.313 1.583,0.719 false 1.583,0.719 1.833,0.719 false 1.74,1.354 1.74,1.771 false 1.74,1.771 1.938,1.771 false 0.083,0.052 0.458,0.333 0.375,0.281 10 false *a 1.875,0.635 2.146,0.823 0.271,0.188 10 false + 2.01,1.688 2.281,1.875 0.271,0.188 10 false -
*a Component without harness connected
(Outer Rear View Mirror RH)


Check that the outer rear view mirror indicator turns on.

NOTICE:

Do not apply a voltage of more than 6 V.


i.

Connect 4 new 1.5 V dry-cell batteries in series.


ii.

Apply 6 V battery voltage to the terminals of the connector, and check that the outer rear view mirror indicator comes on.OK:

OK:
Connection Specified Condition
6 V battery positive (+) → Terminal 1 (+)
6 V battery negative (-) → Terminal 2 (-)
Indicator turns on




Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR RH - MIRROR SUB-ASSEMBLY RH)

NG

REPLACE OUTER REAR VIEW MIRROR RH (OUTER REAR VIEW MIRROR INDICATOR RH)

4.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR RH - MIRROR SUB-ASSEMBLY RH)
a.

Disconnect connector z17 from the outer mirror control ECU assembly RH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z17-7 (BDIR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT OUTER MIRROR CONTROL ECU ASSEMBLY RH

NG

REPLACE MIRROR SUB-ASSEMBLY RH

5.INSPECT OUTER MIRROR CONTROL ECU ASSEMBLY RH
a.

Disconnect connector J13 from the outer mirror control ECU assembly RH.


b.
E233744C21
2.219,0.208 2.646,0.469 0.427,0.26 2.563,1.208 2.771,1.656 false 2.354,0.25 2.844,0.573 0.49,0.323 10 false J13 2.604,1.667 3.208,1.938 0.604,0.271 10 false BDSR 0.146,0.104 0.563,0.438 0.417,0.333 10 false *a
*a Component without harness connected
(Outer Mirror Control ECU Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J13-10 (BDSR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH