Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM2040EQ _58 Vehicle Interior _014724 LIGHTING (INT) _0075072 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  IG Signal Circuit  


DESCRIPTION

This circuit detects the power switch on (IG) or off condition, and sends it to the main body ECU (multiplex network body ECU).

WIRING DIAGRAM

E227478
0.354,0.667 1.24,1.24 0.885,0.573 10 false from Auxiliary Battery 0.375,1.156 1.208,2.073 0.833,0.917 10 false from Power Management Control ECU 3.469,2.458 6.167,2.635 2.698,0.177 10 false Instrument Panel Junction Block Assembly 5.49,2.885 7.146,3.25 1.656,0.365 10 false Main Body ECU (Multiplex Network Body ECU) 3.646,0.948 3.948,1.177 0.302,0.229 10 false 27 3.625,1.146 4.021,1.51 0.396,0.365 10 false 3A 4.146,1.427 4.917,1.719 0.771,0.292 10 false IG1 NO. 2 4.781,0.833 5.917,1.135 1.135,0.302 10 false ECU-IG1 NO. 2 6.26,0.688 6.698,1.073 0.438,0.385 10 false IG 3.688,1.719 4.083,2.083 0.396,0.365 10 false 7 3.625,1.917 4.073,2.229 0.448,0.313 10 false 3B 5.875,0.479 6.26,0.781 0.385,0.302 10 false 32 5.854,0.667 6.25,0.979 0.396,0.313 10 false MB 2.292,0.844 2.813,1.073 0.521,0.229 10 false DC/DC 3.688,0.479 3.979,0.813 0.292,0.333 10 false 1 3.656,0.677 3.99,0.979 0.333,0.302 10 false 3F

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the display on the intelligent tester.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
IG SW Power switch on (IG) signal ON or OFF ON: Power switch on (IG)
OFF: Power switch off
-
Body Electrical > Main Body > Data List
Tester Display
IG SW
50003 123 30
OK:

Normal conditions listed above are displayed.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)
a.

Disconnect the 3A, 3B and 3F instrument panel junction block assembly connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3F-1 - Body ground Power switch off 11 to 14 V
3A-27 - Body ground Power switch on (IG) 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3B-7 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO. 2 RELAY)
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

E191506
1.927,0.281 2.24,0.49 0.313,0.208 5.281,0.365 5.594,0.573 0.313,0.208 4.563,2.354 4.875,2.563 0.313,0.208 1.135,2.198 1.458,2.406 0.323,0.208 6.531,3 6.688,3.49 false 2,0.313 2.26,0.521 0.26,0.208 10 false 3A 5.365,0.396 5.625,0.604 0.26,0.208 10 false 3B 4.615,2.385 4.875,2.594 0.26,0.208 10 false MB 6.635,3.51 6.844,3.708 0.208,0.198 10 false IG 0.271,0.052 0.458,0.24 0.188,0.188 10 false *a 1.219,2.219 1.479,2.427 0.26,0.208 10 false 3F
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
3F-1 - MB-32 (IG) Always 10 kΩ or higher
3F-1 - MB-32 (IG) Auxiliary battery positive (+) → 3A-27
Auxiliary battery negative (-) → 3B-7
Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY