Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM2040EQ _58 Vehicle Interior _014724 LIGHTING (INT) _0075072 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Front Door Courtesy Switch Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) detects the condition of the front door courtesy light switch assembly using this circuit.

WIRING DIAGRAM

E235090
5.646,0.854 6.052,1.104 0.406,0.25 10 false MB 5.667,1.938 5.844,2.115 0.177,0.177 10 false 19 5.667,2.125 5.938,2.302 0.271,0.177 10 false I13 5.708,0.688 5.875,0.896 0.167,0.208 10 false 2 4.469,0.677 4.781,0.958 0.313,0.281 10 false 15 4.458,0.854 4.771,1.094 0.313,0.24 10 false 3C 6.01,0.875 6.573,1.167 0.563,0.292 10 false FLCY 6.01,2.135 6.542,2.385 0.531,0.25 10 false FRCY 1.115,1.083 1.458,1.26 0.344,0.177 10 false N7 1.115,1.24 4.094,1.458 2.979,0.219 10 false Front Door Courtesy Light Switch Assembly LH 1.083,2.323 1.531,2.656 0.448,0.333 10 false O10 1.083,2.49 4.156,2.729 3.073,0.24 10 false Front Door Courtesy Light Switch Assembly RH 3.177,2.021 3.427,2.271 0.25,0.25 10 false 1 3.177,0.76 3.479,1.052 0.302,0.292 10 false 1 4.323,1.365 5.927,1.833 1.604,0.469 10 false Instrument Panel Junction Block Assembly 5.458,2.813 7.104,3.219 1.646,0.406 10 false Main Body ECU (Multiplex Network Body ECU)

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the display on the intelligent tester.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Courtesy Front door courtesy light switch RH signal ON or OFF ON: Front door RH open
OFF: Front door RH closed
-
FL Door Courtesy Front door courtesy light switch LH signal ON or OFF ON: Front door LH open
OFF: Front door LH closed
-
Body Electrical > Main Body > Data List
Tester Display
FR Door Courtesy
FL Door Courtesy
50003 123 197,199
OK:

Normal conditions listed above are displayed.


Result:
Result Proceed to
OK A
Front door courtesy light switch LH or RH does not operate B




A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (LH OR RH)
2.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (LH OR RH)
a.

Remove the front door courtesy light switch assembly.

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>REMOVAL


b.

Inspect the front door courtesy light switch assembly.

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>INSPECTION

OK:

Front door courtesy light switch assembly is normal.


Result:
Result Proceed to
OK (for Front LH) A
OK (for Front RH) B
NG C




A

3.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

B

5.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY RH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

C

REPLACE FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3C instrument panel junction block assembly connector.


b.

Disconnect the N7 front door courtesy light switch assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N7-1 - 3C-15 Always Below 1 Ω
N7-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

E173023
1.25,0.26 1.531,0.458 0.281,0.198 4.635,0.26 4.917,0.458 0.281,0.198 3.167,1.042 3.167,1.365 3.167,1.365 3.292,1.365 false 0.167,0.094 0.469,0.365 0.302,0.271 10 *a 1.302,0.292 1.604,0.51 0.302,0.219 10 3C 3.323,1.292 3.823,1.49 0.5,0.198 10 FLCY 4.677,0.292 5.104,0.563 0.427,0.271 10 MB
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
3C-15 - MB-2 (FLCY) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY RH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the I13 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the O10 front door courtesy light switch assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O10-1 - I13-19 (FRCY) Always Below 1 Ω
O10-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR