Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM2040EQ _58 Vehicle Interior _014724 LIGHTING (INT) _0075072 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Power Switch Illumination Circuit  


DESCRIPTION

The illuminated entry system controls the power switch illumination.

WIRING DIAGRAM

E237082
2.958,1.177 3.615,1.521 0.656,0.344 10 false AGND 4.719,1.302 5.313,1.583 0.594,0.281 10 false AGND 3.01,0.781 3.531,0.99 0.521,0.208 10 false SWIL 4.719,0.906 5.177,1.177 0.458,0.271 10 false SWIL 4.479,1.104 4.656,1.281 0.177,0.177 10 false 6 4.479,0.719 4.656,0.896 0.177,0.177 10 false 6 4.427,0.885 4.719,1.063 0.292,0.177 10 false I87 4.427,1.281 4.719,1.458 0.292,0.177 10 false I86 3.469,1.177 3.563,1.354 0.094,0.177 10 false 6 3.469,0.781 3.563,0.958 0.094,0.177 10 false 9 1.906,1.75 2.219,1.927 0.313,0.177 10 false I58 1.906,1.917 3.021,2.094 1.115,0.177 10 false Power Switch 4.333,1.74 6.146,2.073 1.813,0.333 10 false Certification ECU (Smart Key ECU Assembly)

PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Entry&Start / Active Test.


e.

Check that the illumination operates.

Body Electrical > Entry&Start > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Power/Engine SW Light Power switch light OFF/ON When performing this Active Test, make sure the following condition is met:
The power switch illumination is off (15 seconds or more have elapsed since it turned from on to off) and the power switch is on (ACC) or on (IG), or the hybrid control system is running.
Body Electrical > Entry&Start > Active Test
Tester Display
Power/Engine SW Light
50004 125 27
OK:

Power switch illumination comes on.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT POWER SWITCH
2.INSPECT POWER SWITCH
a.

b.

Inspect the power switch.

Click hereEngine / Hybrid System>2AR-FXE STARTING>POWER SWITCH>INSPECTION

OK:

Power switch illumination comes on.


Result:
Proceed to
OK
NG




OK

3.CHECK HARNESS AND CONNECTOR (POWER SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

NG

3.CHECK HARNESS AND CONNECTOR (POWER SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the I87 and I86 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the I58 power switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I58-9 (SWIL) - I87-6 (SWIL) Always Below 1 Ω
I58-6 (AGND) - I86-6 (AGND) Always Below 1 Ω
I58-9 (SWIL) - Body ground Always 10 kΩ or higher
I58-6 (AGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR