Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM2040EQ _58 Vehicle Interior _014730 HEATING / AIR CONDITIONING _0075108 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  B1413/13  Evaporator Temperature Sensor Circuit  


DESCRIPTION

The evaporator temperature sensor (No. 1 cooler thermistor) is installed on the evaporator in the air conditioner unit to detect the temperature of the air that has passed through the evaporator. Its signal is used for air conditioing control. It sends signals to the air conditioning amplifier assembly. The resistance of the evaporator temperature sensor (No. 1 cooler thermistor) changes in accordance with the cooled air temperature that has passed through the evaporator. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.

The air conditioning amplifier assembly applies voltage (5 V) to the evaporator temperature sensor (No. 1 cooler thermistor) and reads voltage changes as the resistance of the evaporator temperature sensor (No. 1 cooler thermistor) changes. This sensor is used for frost prevention.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1413/13 Evaporator Temperature Sensor Circuit Open or short in evaporator temperature sensor (No. 1 cooler thermistor) circuit
·

Evaporator temperature sensor (No. 1 cooler thermistor)

·

Air conditioning harness assembly

·

Air conditioning amplifier assembly


Memorized
(4 sec. or more)*1

*1: The air conditioning amplifier assembly stores the DTC of the respective malfunction if it has occurred for the period of time indicated in the brackets.


WIRING DIAGRAM

E229251
2.031,1.406 2.25,1.667 0.219,0.26 10 false 1 2.031,0.438 2.313,0.844 0.281,0.406 10 false 2 4.802,0.448 4.948,0.708 0.146,0.26 10 false 6 4.792,1.396 5.021,1.615 0.229,0.219 10 false 5 4.969,0.5 5.302,0.677 0.333,0.177 10 false TEA 2.688,1.906 4.219,2.26 1.531,0.354 10 false Air Conditioning Harness Assembly 4.969,1.448 5.292,1.625 0.323,0.177 10 false SGA 0.469,1.823 0.708,2 0.24,0.177 10 false a1 0.469,1.99 2.427,2.396 1.958,0.406 10 false Evaporator Temperature Sensor (No. 1 Cooler Thermistor) 4.719,1.875 5.01,2.083 0.292,0.208 10 false z1 4.719,2.021 6.302,2.396 1.583,0.375 10 false Air Conditioning Amplifier Assembly

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Air Conditioner / Data List.


e.

Check the value(s) by referring to the table below.

Body Electrical > Air Conditioner > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Evaporator Fin Thermistor Evaporator temperature sensor (No. 1 cooler thermistor) Min.: -29.70°C (-21.46°F)
Max.: 59.55°C (139.19°F)
Actual evaporator temperature displayed -
Body Electrical > Air Conditioner > Data List
Tester Display
Evaporator Fin Thermistor
50003 121 3
OK:

The display is as specified in the normal condition column.



Result:
Result Proceed to
NG A
OK (When troubleshooting according to Problem Symptoms Table) B
OK (When troubleshooting according to the DTC) C



A

2.INSPECT EVAPORATOR TEMPERATURE SENSOR (NO. 1 COOLER THERMISTOR)

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

C

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

2.INSPECT EVAPORATOR TEMPERATURE SENSOR (NO. 1 COOLER THERMISTOR)
a.

Remove the evaporator temperature sensor (No. 1 cooler thermistor).

Click hereVehicle Interior>HEATING / AIR CONDITIONING>FRONT EVAPORATOR TEMPERATURE SENSOR>REMOVAL

E254352
2.302,1.51 2.604,1.719 0.302,0.208 5.604,1.375 5.75,1.083 false 0.24,1.656 0.354,1.219 false 1.521,0.615 1.833,0.771 0.313,0.156 10 false *a 0.313,1.042 0.625,1.198 0.313,0.156 10 false *b 4.417,0.26 4.729,0.417 0.313,0.156 10 false *c 5.927,2.417 6.24,2.573 0.313,0.156 10 false *d 5.75,0.906 6.063,1.063 0.313,0.156 10 false *e 2.375,1.51 2.573,1.729 0.198,0.219 10 false a1
*a Component without harness connected
(Evaporator Temperature Sensor (No. 1 Cooler Thermistor))
*b Sensing Portion
*c Resistance (kΩ) *d Temperature (°C (°F))
*e Allowable Range - -



b.

Disconnect the a1 evaporator temperature sensor (No. 1 cooler thermistor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a1-1 - a1-2 -10°C (14°F) 7.30 to 9.10 kΩ
a1-1 - a1-2 -5°C (23°F) 5.65 to 6.95 kΩ
a1-1 - a1-2 0°C (32°F) 4.40 to 5.35 kΩ
a1-1 - a1-2 5°C (41°F) 3.40 to 4.15 kΩ
a1-1 - a1-2 10°C (50°F) 2.70 to 3.25 kΩ
a1-1 - a1-2 15°C (59°F) 2.14 to 2.58 kΩ
a1-1 - a1-2 20°C (68°F) 1.71 to 2.05 kΩ
a1-1 - a1-2 25°C (77°F) 1.38 to 1.64 kΩ
a1-1 - a1-2 30°C (86°F) 1.11 to 1.32 kΩ


NOTICE:
·

Hold the sensor only by its connector. Touching the sensor may change the resistance value.

·

When measuring, the sensor temperature must be the same as the ambient temperature.



HINT:

As the temperature increases, the resistance decreases (see the graph).



Result:
Proceed to
OK
NG



OK

3.INSPECT AIR CONDITIONING HARNESS ASSEMBLY

NG

REPLACE EVAPORATOR TEMPERATURE SENSOR (NO. 1 COOLER THERMISTOR)

3.INSPECT AIR CONDITIONING HARNESS ASSEMBLY
a.
E161765
0.552,2.271 0.917,2.51 0.365,0.24 1.594,2.74 2.063,3.083 false 1.406,2.729 1.156,3.083 false 0.188,0.188 0.75,0.76 0.563,0.573 10 false *a 0.667,2.302 0.969,2.583 0.302,0.281 10 false z1 1.021,3.083 1.5,3.323 0.479,0.24 10 false SGA 1.948,3.083 2.344,3.271 0.396,0.188 10 false TEA
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Remove the air conditioning harness assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>DISASSEMBLY


b.
E124472
0.667,1.75 1.031,1.99 0.365,0.24 0.188,0.177 0.531,0.583 0.344,0.406 10 false *a 0.792,1.781 1.208,2.135 0.417,0.354 10 false a1
*a Front view of wire harness connector
(to Evaporator Temperature Sensor (No. 1 Cooler Thermistor))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z1-6 (TEA) - a1-2 Always Below 1 Ω
z1-5 (SGA) - a1-1 Always Below 1 Ω
z1-6 (TEA) - Body ground Always 10 kΩ or higher
z1-5 (SGA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPLACE AIR CONDITIONING HARNESS ASSEMBLY