Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM2040EQ _58 Vehicle Interior _014730 HEATING / AIR CONDITIONING _0075108 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  B14A3  Front Passenger Side Solar Sensor Short Circuit  


DESCRIPTION

E107008E25
0.563,0.177 2.625,0.677 2.063,0.5 10 false Resistance of Photodiode 0.5,0.573 0.958,0.823 0.458,0.25 10 false High 0.51,2.198 0.969,2.469 0.458,0.271 10 false Low 0.969,2.563 1.49,2.813 0.521,0.25 10 false Weak 2.333,2.552 3,2.99 0.667,0.438 10 false Strong 0.979,2.927 2.917,3.188 1.938,0.26 10 false Strength of Solar Radiation

The solar sensor (automatic light control sensor) is installed on the upper side of the instrument panel. It detects sunlight and creates a signal that is used for air conditioning control in AUTO mode. The output voltage from the solar sensor (automatic light control sensor) varies in accordance with the amount of sunlight. When the sunlight increases, the output voltage increases. As the sunlight decreases, the output voltage decreases. The air conditioning amplifier assembly detects changes in the output voltage from the solar sensor (automatic light control sensor).

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B14A3 Front Passenger Side Solar Sensor Short Circuit Short in passenger side solar sensor (automatic light control sensor) circuit
·

Solar sensor (automatic light control sensor)

·

Harness or connector between solar sensor (automatic light control sensor) and air conditioning amplifier assembly

·

Harness or connector between solar sensor (automatic light control sensor) and main body ECU (multiplex network body ECU)

·

Main body ECU (multiplex network body ECU)

·

Air conditioning amplifier assembly


Memorized
(4 sec. or more)*1

*1: The air conditioning amplifier assembly stores the DTC of the respective malfunction if it has occurred for the period of time indicated in the brackets.


WIRING DIAGRAM

E229255E57
1.521,0.5 2.021,0.792 0.5,0.292 10 false CLTB 0.5,2.969 0.729,3.125 0.229,0.156 10 false I61 1.99,0.979 2.115,1.146 0.125,0.167 10 false 3 1.99,0.406 2.115,0.573 0.125,0.167 10 false 6 4.854,2.448 5.031,2.615 0.177,0.167 10 false 32 1.51,1.083 2.042,1.292 0.531,0.208 10 false CLTE 4.813,0.979 5.021,1.146 0.208,0.167 10 false 22 4.813,0.406 5.01,0.573 0.198,0.167 10 false 20 5.146,2.573 5.531,2.729 0.385,0.156 10 false TSP 5.104,0.479 5.49,0.635 0.385,0.156 10 false CLTB 5.104,1.073 5.49,1.229 0.385,0.156 10 false CLTE 4.927,1.521 6.573,1.875 1.646,0.354 10 false Main Body ECU (Multiplex Network Body ECU) 4.656,1.521 4.948,1.677 0.292,0.156 10 false I13 4.948,3.01 6.542,3.563 1.594,0.552 10 false Air Conditioning Amplifier Assembly 4.688,3.01 4.99,3.167 0.302,0.156 10 false I77 1.99,2.479 2.24,2.646 0.25,0.167 10 false 1 1.635,2.583 2.26,2.823 0.625,0.24 10 false TSL 0.74,2.969 2.625,3.448 1.885,0.479 10 false Solar Sensor (Automatic Light Control Sensor)

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Air Conditioner / Data List.


e.

Check the value(s) by referring to the table below.

Body Electrical > Air Conditioner > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Solar Sensor (P Side) Front passenger side solar sensor (automatic light control sensor) Min.: 0
Max.: 255
Front passenger side solar sensor (automatic light control sensor) value increases as brightness increases -
Body Electrical > Air Conditioner > Data List
Tester Display
Solar Sensor (P Side)
50003 121 5
OK:

The display is as specified in the Normal Condition column.



Result:
Result Proceed to
NG A
OK (When troubleshooting according to Problem Symptoms Table) B
OK (When troubleshooting according to the DTC) C



A

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

C

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
E221132C13
1.469,0.823 1.927,1.104 0.458,0.281 1.896,2.698 2.573,2.781 false 1.448,2.469 0.865,2.635 false 0.292,0.229 0.667,0.667 0.375,0.438 10 false *a 0.406,2.563 0.833,2.729 0.427,0.167 10 false CLTE 2.594,2.708 3.021,2.875 0.427,0.167 10 false CLTB 1.625,0.875 2,1.115 0.375,0.24 10 false I61
*a Front view of wire harness connector
(to Solar Sensor (Automatic Light Control Sensor))


Disconnect the I61 solar sensor (automatic light control sensor) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I61-6 (CLTB) - I61-3 (CLTE) Power switch off Below 1 V
I61-6 (CLTB) - I61-3 (CLTE) Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (SOLAR SENSOR (AUTOMATIC LIGHT CONTROL SENSOR) - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - SOLAR SENSOR (AUTOMATIC LIGHT CONTROL SENSOR))
3.CHECK HARNESS AND CONNECTOR (SOLAR SENSOR (AUTOMATIC LIGHT CONTROL SENSOR) - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the I77 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I77-32 (TSP) - I61-1 (TSL) Always Below 1 Ω
I77-32 (TSP) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT SOLAR SENSOR (AUTOMATIC LIGHT CONTROL SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT SOLAR SENSOR (AUTOMATIC LIGHT CONTROL SENSOR)
a.
E221134C18
1.563,0.271 2.021,0.552 0.458,0.281 2.021,1.635 2.677,1.635 false 2.021,1.365 2.677,1.365 false 0.25,0.146 0.729,0.677 0.479,0.531 10 false *a 2.708,1.531 3.25,1.906 0.542,0.375 10 false CLTE 1.719,0.333 2.198,0.615 0.479,0.281 10 false I61 2.719,1.281 3.25,1.583 0.531,0.302 10 false TSL
*a Component with harness connected
(Solar Sensor (Automatic Light Control Sensor))


Remove the solar sensor (automatic light control sensor).

Click hereVehicle Interior>HEATING / AIR CONDITIONING>SOLAR SENSOR>REMOVAL


b.

Reconnect the I61 solar sensor (automatic light control sensor) connector.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I61-1 (TSL) - I61-3 (CLTE) Sensor is subjected to electric light 0.8 to 4.3 V
I61-1 (TSL) - I61-3 (CLTE) Sensor is covered with a cloth Below 0.8 V


NOTICE:
·

The connection procedure for using a digital tester such as a TOYOTA electrical tester is shown above. When using an analog tester, connect the negative (-) lead to terminal 1 and the positive (+) lead to terminal 6 of the solar sensor (automatic light control sensor).

·

Do not bring the positive and negative tester probes too close to each other as a short circuit may occur.



HINT:
·

Use an incandescent light for inspection. Bring it within about 30 cm (11.8 in.) of the solar sensor (automatic light control sensor).

·

As the inspection light is moved away from the sensor, the voltage decreases.




Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPLACE SOLAR SENSOR (AUTOMATIC LIGHT CONTROL SENSOR)

5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - SOLAR SENSOR (AUTOMATIC LIGHT CONTROL SENSOR))
a.

Disconnect the I13 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I13-20 (CLTB) - I61-6 (CLTB) Always Below 1 Ω
I13-22 (CLTE) - I61-3 (CLTE) Always Below 1 Ω
I13-20 (CLTB) - Body ground Always 10 kΩ or higher
I13-22 (CLTE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR