The cruise control main switch is used to turn the dynamic radar cruise control system on and off, as well as operate 8 functions: SET, -(COAST), TAP-DOWN, RES (RESUME), + (ACCEL), TAP-UP, CANCEL and MODE. The SET, TAP-DOWN and - (COAST) functions, and the RES (RESUME), TAP-UP and + (ACCEL) functions are operated with the same switch. The cruise control main switch is an automatic return type switch which turns on only while it is being operated and turns off when it is released. The driving support ECU assembly then reads the voltage value that has been changed by the switch operation to control MODE, SET, -, RES, +, or CANCEL function. The dynamic radar cruise control system has 2 cruise control modes: constant speed control mode and vehicle-to-vehicle distance control mode.
Vehicle-to-vehicle distance control mode is selected by default when the dynamic radar cruise control system is turned on using the cruise control main switch.
The operation of constant speed control mode is the same as that for a conventional cruise control system.
The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Radar Cruise / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Cruise Control Main Switch | Cruise control switch signal | ON or OFF | ON: Cruise control main switch pushed
OFF: Cruise control main switch released |
- |
| RES/ACC Switch | +/RES switch signal | ON or OFF | ON: +/RES switch on
OFF: +/RES switch off |
- |
| SET/COAST Switch | -/SET switch signal | ON or OFF | ON: -/SET switch on
OFF: -/SET switch off |
- |
| Constant Speed Mode | Cruise control mode signal | All Spd, Hi Spd or Normal | All Spd: Vehicle-to-vehicle distance control mode (w/ full-speed following function)
Hi Spd: Vehicle-to-vehicle distance control mode (w/o full-speed following function) Normal: Constant speed mode |
- |
| Cancl CCS by Com Delay | Dynamic radar cruise control system (constant speed mode) cancel signal | ON or OFF | ON: Cancel signal on
OFF: Cancel signal off |
- |
| Tester Display |
|---|
| Cruise Control Main Switch |
| RES/ACC Switch |
| SET/COAST Switch |
| Constant Speed Mode |
| Cancl CCS by Com Delay |
When the cruise control main switch is operated, the display changes as shown above.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE
NG
Remove the cruise control main switch.
Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL MAIN SWITCH>REMOVAL
Inspect the cruise control main switch.
Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL MAIN SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Spiral Cable with Sensor Sub-assembly) |
| *b | Front view of wire harness connector
(to Cruise Control Main Switch) |
Disconnect the cruise control switch wire.
Disconnect the cruise control main switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z2-1 (R/N) - A-2 (R/N) | Always | Below 1 Ω |
| z2-3 (CCS) - A-3 (CCS) | Always | Below 1 Ω |
| z2-4 (ECC) - A-1 (ECC) | Always | Below 1 Ω |
| z2-1 (R/N) or A-2 (R/N) - Body ground | Always | 10 kΩ or higher |
| z2-3 (CCS) or A-3 (CCS) - Body ground | Always | 10 kΩ or higher |
| z2-4 (ECC) or A-1 (ECC) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the spiral cable with sensor sub-assembly.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL
Inspect the spiral cable with sensor sub-assembly.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I28 spiral cable with sensor sub-assembly connector.
Disconnect the I176 driving support ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I28-1 (CCS) - I176-23 (CCS) | Always | Below 1 Ω |
| I28-8 (R/N) - I176-10 (CCHG) | Always | Below 1 Ω |
| I28-2 (ECC) - Body ground | Always | Below 1 Ω |
| I28-1 (CCS) or I176-23 (CCS) - Body ground | Always | 10 kΩ or higher |
| I28-8 (R/N) or I176-10 (CCHG) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG