Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2015.04
RM2040EQ _51 Engine / Hybrid System _014700 CRUISE CONTROL _0166042 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  C1A05  Stop Light Switch Circuit  


DESCRIPTION

When the brake pedal is depressed, the stop light switch assembly sends a brake pedal operation signal to the driving support ECU assembly. After reception of this signal, the driving support ECU assembly cancels the dynamic radar cruise control system. When the driving support ECU assembly detects a problem in the stop light switch assembly circuit, DTC C1A05 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A05 Stop Light Switch Circuit When the power switch on (IG) and cruise control main switch is on, the driving support ECU assembly detects a malfunction in the signal from stop light switch assembly circuit for 1.532 seconds.
·

Stop light switch assembly

·

Driving support ECU assembly

·

Harness or connector



WIRING DIAGRAM

B381526E02
5.24,2.031 7.156,2.26 1.917,0.229 10 false Driving Support ECU Assembly 2.229,2.021 4.031,2.219 1.802,0.198 10 false Stop Light Switch Assembly 2.24,1.875 2.698,2.073 0.458,0.198 10 false A33 5.24,1.885 5.854,2.083 0.615,0.198 10 false I176 5.698,0.75 6.115,0.948 0.417,0.198 10 false ST1- 5.688,1.552 6.146,1.75 0.458,0.198 10 false STP- 0.135,0.75 1.844,0.948 1.708,0.198 10 false from ECU-IG2 NO. 3 Fuse 0.708,1.542 1.802,1.781 1.094,0.24 10 false from STOP Fuse 5.438,0.667 5.75,0.865 0.313,0.198 10 false 28 5.427,1.427 5.74,1.625 0.313,0.198 10 false 27 2.479,0.656 2.635,0.854 0.156,0.198 10 false 4 2.49,1.427 2.656,1.625 0.167,0.198 10 false 2 3.667,0.646 3.823,0.844 0.156,0.198 10 false 3 3.667,1.438 3.823,1.635 0.156,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the driving support ECU assembly, make sure to replace it with a new one. If a device which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle, and as a result, a DTC may be stored.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)
a.
E144327C22
0.406,1.958 0.823,2.219 0.417,0.26 0.49,2.01 1.094,2.427 0.604,0.417 10 false A33 0.24,0.177 0.656,0.573 0.417,0.396 10 false *a
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the A33 stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A33-4 - Body ground Power switch off 11 to 14 V
A33-2 - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)

2.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the I176 driving support ECU assembly connector.


b.

Disconnect the A33 stop light switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I176-27 (STP-) - A33-1 Always Below 1 Ω
I176-28 (ST1-) - A33-3 Always Below 1 Ω
I176-27 (STP-) or A33-1 - Body ground Always 10 kΩ or higher
I176-28 (ST1-) or A33-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE DRIVING SUPPORT ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR