Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2015.04
RM2040EQ _51 Engine / Hybrid System _014700 CRUISE CONTROL _0166042 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  C1A40  ENG / EHV Device  


DESCRIPTION

When the driving support ECU assembly receives a hybrid control system or SFI system malfunction signal from the power management control ECU or ECM via CAN communication, this DTC is stored.

When DTC C1A40 is stored, the hybrid control system or SFI system DTC will also be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A40 ENG / EHV Device While the power switch is on (IG), a hybrid control system or SFI system malfunction signal is detected for 1.372 seconds or more while the vehicle is being driven at a speed of 36 km/h (22 mph) or more.
·

Hybrid control system

·

SFI system

·

Power management control ECU

·

ECM

·

Driving support ECU assembly



WIRING DIAGRAM

E230010E24
1.333,0.604 1.781,0.771 0.448,0.167 10 false CANH 1.344,1.104 1.792,1.271 0.448,0.167 10 false CANL 5.531,0.594 5.979,0.76 0.448,0.167 10 false CA2H 5.531,1.094 5.979,1.26 0.448,0.167 10 false CA2L 3.938,0.594 4.385,0.76 0.448,0.167 10 false CA2H 3.958,1.104 4.406,1.271 0.448,0.167 10 false CA2L 2.979,0.594 3.427,0.76 0.448,0.167 10 false CA1H 2.979,1.104 3.427,1.271 0.448,0.167 10 false CA1L 1.792,0.427 1.99,0.583 0.198,0.156 10 false 13 1.792,0.917 2,1.125 0.208,0.208 10 false 26 4.438,0.417 4.635,0.573 0.198,0.156 10 false 35 4.438,0.906 4.635,1.063 0.198,0.156 10 false 34 2.677,0.417 2.875,0.573 0.198,0.156 10 false 25 2.677,0.906 2.875,1.063 0.198,0.156 10 false 24 5.302,0.427 5.5,0.583 0.198,0.156 10 false 39 5.292,0.917 5.49,1.073 0.198,0.156 10 false 17 2.698,0.604 2.917,0.781 0.219,0.177 10 false I4 2.698,1.104 2.917,1.281 0.219,0.177 10 false I4 4.469,0.604 4.688,0.781 0.219,0.177 10 false I3 4.469,1.094 4.688,1.271 0.219,0.177 10 false I3 0.531,1.656 0.802,1.813 0.271,0.156 10 false A25 0.844,1.656 1.177,1.823 0.333,0.167 10 false ECM 3.052,1.698 4.333,2.135 1.281,0.438 10 false Power Management Control ECU 5.208,1.594 5.604,1.781 0.396,0.188 10 false I176 5.219,1.74 7.125,1.938 1.906,0.198 10 false Driving Support ECU Assembly 0.865,2.302 2.667,2.448 1.802,0.146 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

When replacing the driving support ECU assembly, make sure to replace it with a new one. If a device which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle, and as a result, a DTC may be stored.


PROCEDURE

1.CHECK FOR DTCS (HYBRID CONTROL SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


e.

Check for DTCs.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Hybrid Control > Trouble Codes
50001 236

Result:
Result Proceed to
Hybrid control system DTCs are not output A
Hybrid control system DTCs are output B



A

2.CHECK FOR DTCS (SFI SYSTEM)

B

2.CHECK FOR DTCS (SFI SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Check for DTCs.

Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Result Proceed to
SFI system DTCs are not output A
SFI system DTCs are output B



A

3.REPLACE POWER MANAGEMENT CONTROL ECU

B

3.REPLACE POWER MANAGEMENT CONTROL ECU
a.

Replace the power management control ECU with a new one.

Click herePower Source / Network>POWER DISTRIBUTION>POWER MANAGEMENT CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTCS (DTC C1A40)
4.CHECK FOR DTCS (DTC C1A40)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise > Clear DTCs
50002 197

e.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.


i.

Drive the vehicle at a speed for which dynamic radar cruise control system operation is possible.


ii.

Turn the cruise control system on using the cruise control main switch (ON-OFF button).


iii.

Push the cruise control main switch to -/SET to begin control of vehicle speed using the cruise control system.



f.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise > Trouble Codes
50001 197

Result:
Result Proceed to
DTC C1A40 is not output A
DTC C1A40 is output B



A

END (POWER MANAGEMENT CONTROL ECU WAS DEFECTIVE)

B

5.REPLACE ECM
5.REPLACE ECM

NEXT

6.CHECK FOR DTCS (DTC C1A40)
6.CHECK FOR DTCS (DTC C1A40)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise > Clear DTCs
50002 197

e.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.


i.

Drive the vehicle at a speed for which dynamic radar cruise control system operation is possible.


ii.

Turn the cruise control system on using the cruise control main switch (ON-OFF button).


iii.

Push the cruise control main switch to -/SET to begin control of vehicle speed using the cruise control system.



f.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise > Trouble Codes
50001 197

Result:
Result Proceed to
DTC C1A40 is not output A
DTC C1A40 is output B



A

END (ECM WAS DEFECTIVE)

B

REPLACE DRIVING SUPPORT ECU ASSEMBLY