Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2015.04
RM2040EQ _58 Vehicle Interior _035749 PRE-CRASH SAFETY _0166048 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  C1A40  ENG / EHV Device  


DESCRIPTION

When the driving support ECU assembly receives a hybrid control system or SFI system malfunction signal from the power management control ECU or ECM, this DTC is stored.

When DTC C1A40 is stored, the hybrid control system or SFI system DTC will also be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A40 ENG / EHV Device While the power switch is on (IG), a hybrid control system or SFI system malfunction signal is detected for 3 seconds or more.
·

Hybrid control system

·

SFI system

·

Power management control ECU

·

Driving support ECU assembly

·

ECM



CAUTION / NOTICE / HINT

NOTICE:

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.


PROCEDURE

1.CHECK FOR DTCS (HYBRID CONTROL SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


e.

Check for DTCs.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Hybrid Control > Trouble Codes
50001 236
Result:
Result Proceed to
Hybrid control system DTCs are not output A
Hybrid control system DTCs are output B




A

2.CHECK FOR DTCS (SFI SYSTEM)

B

2.CHECK FOR DTCS (SFI SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Check for DTCs.

Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
SFI system DTCs are not output A
SFI system DTCs are output B




A

3.REPLACE DRIVING SUPPORT ECU ASSEMBLY

B

3.REPLACE DRIVING SUPPORT ECU ASSEMBLY
a.

Replace the driving support ECU assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTCS (PRE-CRASH 2)
4.CHECK FOR DTCS (PRE-CRASH 2)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

e.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



f.

Check for DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220
Result:
Result Proceed to
DTC C1A40 is output A
DTC C1A40 is not output B




A

5.REPLACE POWER MANAGEMENT CONTROL ECU

B

END (DRIVING SUPPORT ECU ASSEMBLY WAS DEFECTIVE)

5.REPLACE POWER MANAGEMENT CONTROL ECU
a.

Replace the power management control ECU with a new one.

Click herePower Source / Network>POWER DISTRIBUTION>POWER MANAGEMENT CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTCS (PRE-CRASH 2)
6.CHECK FOR DTCS (PRE-CRASH 2)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

e.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



f.

Check for DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220
Result:
Result Proceed to
DTC C1A40 is not output A
DTC C1A40 is output B




A

END (POWER MANAGEMENT CONTROL ECU WAS DEFECTIVE)

B