Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2015.04
RM2040EQ _58 Vehicle Interior _035749 PRE-CRASH SAFETY _0166048 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  C1A41  Brake Request Value Mismatch between ENG / EHV and Driving Support ECU  


DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) receives brake control request signals from the power management control ECU and driving support ECU assembly.

When the request signals received from the power management control ECU and driving support ECU assembly are not consistent, the skid control ECU (brake booster with master cylinder assembly) determines that a malfunction has occurred and sends a malfunction signal to the driving support ECU assembly.

If the driving support ECU assembly receives a malfunction signal, DTC C1A41 is output. Although the skid control ECU (brake booster with master cylinder assembly) sends a malfunction signal to the driving support ECU assembly, the electronically controlled brake system does not output a relevant malfunction detection DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A41 Brake Request Value Mismatch between ENG / EHV and Driving Support ECU While the power switch is on (IG), the skid control ECU (brake booster with master cylinder assembly) detects a significant difference in the brake request signal from the power management control ECU and driving support ECU assembly for 2.992 seconds or more.
·

Electronically controlled brake system

·

Hybrid control system

·

Power management control ECU

·

Skid control ECU (Brake booster with master cylinder assembly)

·

Driving support ECU assembly



CAUTION / NOTICE / HINT

NOTICE:

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.


PROCEDURE

1.CHECK FOR DTCS (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.


e.

Check for DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
Electronically controlled brake system DTCs are not output A
Electronically controlled brake system DTCs are output B




A

2.CHECK FOR DTCS (HYBRID CONTROL SYSTEM)

B

2.CHECK FOR DTCS (HYBRID CONTROL SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


e.

Check for DTCs.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Hybrid Control > Trouble Codes
50001 236
Result:
Result Proceed to
Hybrid control system DTCs are not output A
Hybrid control system DTCs are output B




A

3.REPLACE POWER MANAGEMENT CONTROL ECU

B

3.REPLACE POWER MANAGEMENT CONTROL ECU
a.

Replace the power management control ECU with a new one.

Click herePower Source / Network>POWER DISTRIBUTION>POWER MANAGEMENT CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTCS (PRE-CRASH 2)
4.CHECK FOR DTCS (PRE-CRASH 2)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

e.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



f.

Check for DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220
Result:
Result Proceed to
DTC C1A41 is output A
DTC C1A41 is not output B




A

5.REPLACE SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)

B

END (POWER MANAGEMENT CONTROL ECU WAS DEFECTIVE)

5.REPLACE SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)
a.

Replace the skid control ECU (brake booster with master cylinder assembly) with a new one.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTCS (PRE-CRASH 2)
6.CHECK FOR DTCS (PRE-CRASH 2)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

e.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



f.

Check for DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220
Result:
Result Proceed to
DTC C1A41 is not output A
DTC C1A41 is output B




A

END (SKID CONTROL ECU [BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY] WAS DEFECTIVE)

B

REPLACE DRIVING SUPPORT ECU ASSEMBLY