Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2015.04
RM2040EQ _58 Vehicle Interior _035749 PRE-CRASH SAFETY _0166048 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  C1A46  Yaw Rate Sensor  


DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) receives the airbag sensor assembly (yaw rate sensor) and sends the signals to the driving support ECU assembly. If the skid control ECU (brake booster with master cylinder assembly) detects that the airbag sensor assembly (yaw rate sensor) is malfunctioning, the skid control ECU (brake booster with master cylinder assembly) sends a malfunction signal to the driving support ECU assembly, and the driving support ECU assembly stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A46 Yaw Rate Sensor While the vehicle speed is 5 km/h (3 mph) or more, an airbag sensor assembly (yaw rate sensor) malfunction signal is received from the skid control ECU (brake booster with master cylinder assembly) for 9.632 seconds or more.
·

Electronically controlled brake system

·

Skid control ECU (Brake booster with master cylinder assembly)

·

Driving support ECU assembly



CAUTION / NOTICE / HINT

NOTICE:

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.


PROCEDURE

1.CHECK FOR DTCS (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.


e.

Check for DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
Electronically controlled brake system DTCs are not output A
Electronically controlled brake system DTCs are output B




A

2.REPLACE SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)

B

2.REPLACE SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)
a.

Replace the skid control ECU (brake booster with master cylinder assembly) with a new one.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER>REMOVAL


Result:
Proceed to
NEXT



NEXT

3.CHECK FOR DTCS (PRE-CRASH 2)
3.CHECK FOR DTCS (PRE-CRASH 2)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

e.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



f.

Check for DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220
Result:
Result Proceed to
DTC C1A46 is not output A
DTC C1A46 is output B




A

END (SKID CONTROL ECU [BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY] WAS DEFECTIVE)

B

REPLACE DRIVING SUPPORT ECU ASSEMBLY