Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › from 2015.04
RM2040EQ _51 Engine / Hybrid System _014700 CRUISE CONTROL _0074941 CRUISE CONTROL SYSTEM J

CRUISE CONTROL  CRUISE CONTROL SYSTEM  Cruise Control Switch Circuit  


DESCRIPTION

The cruise control switch is used to turn the cruise control system on and off, as well as operate 7 functions: SET, - (COAST), TAP-DOWN, RES (RESUME), + (ACCEL), TAP-UP and CANCEL. The SET, TAP-DOWN and - (COAST) functions, and the RES (RESUME), TAP-UP and + (ACCEL) functions are operated with the same switch. The cruise control switch is an automatic return type switch which turns on only while operating it in the direction of each arrow and turns off after releasing it. The internal contact points of the cruise control switch turn on with switch operation. Then the power management control ECU reads the voltage value that has been changed by the switch operation to control SET, - (COAST), RES (RESUME), + (ACCEL), and CANCEL.

WIRING DIAGRAM

E229591E33
6.333,0.833 6.677,0.99 0.344,0.156 10 false CCS 6.344,1.521 6.531,1.677 0.188,0.156 10 false E1 6.031,1.521 6.271,1.74 0.24,0.219 10 false I3 6.042,1.313 6.229,1.469 0.188,0.156 10 false 6 5.063,3.073 5.167,3.229 0.104,0.156 10 false 1 5.052,3.969 5.156,4.125 0.104,0.156 10 false 2 3.99,3.073 4.094,3.229 0.104,0.156 10 false 3 3.99,3.969 4.104,4.125 0.115,0.156 10 false 4 6,0.635 6.188,0.792 0.188,0.156 10 false 23 6.031,0.833 6.188,1.073 0.156,0.24 10 false I4 5,3.302 5.271,3.458 0.271,0.156 10 false I28 5,4.188 5.271,4.344 0.271,0.156 10 false I28 3.948,3.292 4.125,3.448 0.177,0.156 10 false z2 4.552,3.188 4.875,3.344 0.323,0.156 10 false CCS 5.865,5.208 7.094,5.646 1.229,0.438 10 false Power Management Control ECU 4.552,4.104 4.875,4.26 0.323,0.156 10 false ECC 3.948,4.188 4.125,4.344 0.177,0.156 10 false z2 1.156,4.708 2.625,4.865 1.469,0.156 10 false Cruise Control Switch 3.229,4.813 4.198,5.135 0.969,0.323 10 false Cruise Control Switch Wire 3.115,4.094 3.438,4.25 0.323,0.156 10 false ECC 3.115,3.188 3.438,3.344 0.323,0.156 10 false CCS 3.5,3.188 3.656,3.344 0.156,0.156 10 false 3 3.49,4.094 3.625,4.25 0.135,0.156 10 false 1 2.875,3.76 3.438,3.917 0.563,0.156 10 false ON-OFF 2.115,3.76 2.583,3.917 0.469,0.156 10 false +/RES 1.344,3.76 1.74,3.917 0.396,0.156 10 false -/SET 0.531,3.76 1.115,3.917 0.583,0.156 10 false CANCEL 4.271,4.656 5.219,5.021 0.948,0.365 10 false Spiral Cable Sub-assembly

PROCEDURE

1.READ VALUE ON INTELLIGENT TESTER
a.
E107091C01
2.144,0.084 2.42,0.273 0.276,0.189 10 *c 2.763,1.172 3.003,1.374 0.24,0.202 10 *a 1.934,1.577 2.325,1.779 0.391,0.202 10 *b 1.033,1.235 1.268,1.437 0.235,0.202 10 *d
*a ON-OFF
*b -/SET
*c +/RES
*d CANCEL


Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Select the following menu items: Powertrain / Cruise Control / Data List.


e.

Check the Data List to confirm proper functioning of the cruise control switch.

Powertrain > Cruise Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Main SW M-CPU Cruise control switch signal (Main CPU) ON or OFF ON: Cruise control switch (ON-OFF button) pushed
OFF: Cruise control switch (ON-OFF button) released
-
Cancel Switch CANCEL switch signal ON or OFF ON: CANCEL switch on
OFF: CANCEL switch off
-
SET/COAST Switch -/SET switch signal ON or OFF ON: -/SET switch on
OFF: -/SET switch off
-
RES/ACC Switch +/RES switch signal ON or OFF ON: +/RES switch on
OFF: +/RES switch off
-
Powertrain > Cruise Control > Data List
Tester Display
Main SW M-CPU
Cancel Switch
SET/COAST Switch
RES/ACC Switch
50003 238 16,23,22,21
OK:

When the cruise control switch is operated, the display changes as shown above.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT CRUISE CONTROL SWITCH
2.INSPECT CRUISE CONTROL SWITCH
a.

b.

Measure the resistance according to the value(s) in the table below.

E265511C14
5.021,1.167 5.5,0.667 5.5,0.667 5.75,0.667 false 1.802,3.375 1.969,3.229 1.969,3.229 2.135,3.083 true 2.708,3.094 3.021,3.375 true 5.781,0.583 6.094,0.74 0.313,0.156 10 false *1 0.083,0.083 0.396,0.24 0.313,0.156 10 false *a 5.917,1.25 6.229,1.406 0.313,0.156 10 false *b 4.604,0.583 4.917,0.74 0.313,0.156 10 false *c 5.021,2.344 5.333,2.5 0.313,0.156 10 false *d 3.833,2.167 4.146,2.323 0.313,0.156 10 false *e 1.49,3.292 1.948,3.49 0.458,0.198 10 false CCS 3.073,3.292 3.531,3.49 0.458,0.198 10 false ECC
*1 Cruise Control Switch (ON-OFF button) - -
*a Component without harness connected
(Cruise Control Switch)
*b ON-OFF
*c +/RES *d -/SET
*e CANCEL - -


Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 3 Cruise control switch (ON-OFF button) released 10 kΩ or higher
Cruise control switch (ON-OFF button) pushed Below 2.5 Ω
+/RES 235 to 245 Ω
-/SET 617 to 643 Ω
CANCEL 1509 to 1571 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK CRUISE CONTROL SWITCH WIRE (SPIRAL CABLE SUB-ASSEMBLY - CRUISE CONTROL SWITCH)

NG

3.CHECK CRUISE CONTROL SWITCH WIRE (SPIRAL CABLE SUB-ASSEMBLY - CRUISE CONTROL SWITCH)
a.
E232246C14
0.24,1.344 0.667,1.646 0.427,0.302 0.542,4.177 0.708,4.052 0.708,4.052 0.823,3.969 true 1.271,3.969 1.531,4.219 true 0.177,0.333 0.344,0.51 0.167,0.177 10 false *a 0.208,2.51 0.375,2.688 0.167,0.177 10 false *b 0.396,1.406 0.833,1.76 0.438,0.354 10 false z2 0.219,4.115 0.677,4.313 0.458,0.198 10 false ECC 1.583,4.146 2.042,4.344 0.458,0.198 10 false CCS
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)
*b Front view of wire harness connector
(to Cruise Control Switch)


Disconnect the spiral cable sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
z2-3 - 3 (CCS) Always Below 1 Ω
z2-4 - 1 (ECC) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK SPIRAL CABLE SUB-ASSEMBLY

NG

REPAIR OR REPLACE CRUISE CONTROL SWITCH WIRE (SPIRAL CABLE SUB-ASSEMBLY - CRUISE CONTROL SWITCH)

4.CHECK SPIRAL CABLE SUB-ASSEMBLY
NOTICE:

The spiral cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable sub-assembly may prevent the airbag from deploying. Be sure to read the pages shown in the brackets.


HINT:


a.
E265512C01
2.25,0.25 2.5,0.417 0.25,0.167 1.583,4.083 1.833,4.25 0.25,0.167 1.74,3.281 2.167,3.083 false 1.74,3.365 2.167,3.531 false 0.104,0.094 0.417,0.25 0.313,0.156 10 *a 2.313,0.25 2.625,0.448 0.313,0.198 10 z2 1.625,4.083 2.083,4.281 0.458,0.198 10 I28 2.208,3 2.667,3.198 0.458,0.198 10 CCS 2.208,3.469 2.667,3.667 0.458,0.198 10 ECC
*a Component without harness connected
(Spiral Cable Sub-assembly)


Remove the spiral cable sub-assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
z2-3 - I28-1 (CCS) Center Below 3 Ω
2.5 rotations to the left
2.5 rotations to the right
z2-4 - I28-2 (ECC) Center Below 3 Ω
2.5 rotations to the left
2.5 rotations to the right



c.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
z2-3 - I28-1 (CCS) Always Below 3 Ω
z2-4 - I28-2 (ECC) Always Below 3 Ω


HINT:

The spiral cable sub-assembly makes a maximum of approximately 5 rotations.



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - SPIRAL CABLE SUB-ASSEMBLY)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - SPIRAL CABLE SUB-ASSEMBLY)
a.

Disconnect the power management control ECU connector.


b.

Disconnect the spiral cable sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
I28-1 (CCS) - I4-23 (CCS) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
I28-1 (CCS) or I4-23 (CCS) - Body ground Always 10 kΩ or higher



d.

Reconnect the spiral cable sub-assembly connector.


e.

Reconnect the power management control ECU connector.


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - POWER MANAGEMENT CONTROL ECU)

6.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)
a.

Disconnect the spiral cable sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
I28-2 (ECC) - Body ground Always Below 1 Ω



c.

Reconnect the spiral cable sub-assembly connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)