Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM › from 2015.04
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074886 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  P0AFC-123  Hybrid Battery Pack Sensor Module  


DESCRIPTION

If the battery smart unit detects an internal malfunction, it sends an error signal to the power management control ECU. When the power management control ECU receives the error signal from the battery smart unit, the ECU warns the driver and performs fail-safe control.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0AFC-123 Hybrid Battery Pack Sensor Module The power management control ECU receives an error signal from the battery smart unit.
·

Battery smart unit

·

Wire harness or connector


Comes on Master Warning Light:
Comes on

WIRING DIAGRAM

A260753E21
5.333,3.531 6.552,3.781 1.219,0.25 10 false Battery Smart Unit 2.281,0.917 2.708,1.208 0.427,0.292 10 false IGCT 4.469,0.479 5.406,0.781 0.938,0.302 10 false BATT VL SSR 0.625,2.646 1.656,3.052 1.031,0.406 10 false Auxiliary Battery 2.698,1.313 3.135,1.573 0.438,0.26 10 false MREL 2.719,2.365 3.125,2.604 0.406,0.24 10 false BTH+ 2.771,2.708 3.146,2.906 0.375,0.198 10 false BTH- 3.146,1.292 3.448,1.438 0.302,0.146 10 false A38 3.188,2.198 3.49,2.344 0.302,0.146 10 false 30 3.219,2.365 3.417,2.552 0.198,0.188 10 false I3 5.656,2.344 6.063,2.573 0.406,0.229 10 false BTH+ 5.656,2.688 6.042,2.927 0.385,0.24 10 false BTH- 5.458,2.271 5.646,2.5 0.188,0.229 10 false 1 5.667,0.302 6.125,0.604 0.458,0.302 10 false IGCT 2.75,0.188 2.979,0.396 0.229,0.208 10 false 5 2.031,0.188 2.24,0.417 0.208,0.229 10 false 3 2.021,0.563 2.219,0.781 0.198,0.219 10 false 2 2.74,0.563 2.938,0.74 0.198,0.177 10 false 1 4.646,0.177 4.771,0.333 0.125,0.156 10 false 1 5.083,0.167 5.229,0.344 0.146,0.177 10 false 2 5.656,3.031 6.021,3.281 0.365,0.25 10 false GND 5.458,2.917 5.688,3.146 0.229,0.229 10 false 6 0.5,0.833 1.281,1.052 0.781,0.219 10 false IGCT-MAIN 0.51,1.948 1.292,2.167 0.781,0.219 10 false MAIN 0.51,1.417 1.292,1.635 0.781,0.219 10 false R/B NO. 2 3.229,1.115 3.427,1.292 0.198,0.177 10 false 4 3.219,2.698 3.438,2.896 0.219,0.198 10 false I3 3.188,2.542 3.417,2.719 0.229,0.177 10 false 29 5.469,2.583 5.698,2.823 0.229,0.24 10 false 4 5.49,0.198 5.635,0.406 0.146,0.208 10 false 3 2.146,3.063 3.479,3.438 1.333,0.375 10 false Power Management Control ECU 5.333,3.375 5.615,3.573 0.281,0.198 10 false N18 2.823,1.656 3.146,1.917 0.323,0.26 10 false +B1 2.813,2 3.167,2.219 0.354,0.219 10 false +B2 3.229,1.49 3.427,1.667 0.198,0.177 10 false 3 3.24,1.844 3.438,2.021 0.198,0.177 10 false 1 3.146,1.656 3.448,1.802 0.302,0.146 10 false A39 3.146,2 3.448,2.146 0.302,0.146 10 false A38 4.323,1.094 5.177,1.323 0.854,0.229 10 false PM IGCT 4.063,0.875 4.229,1.094 0.167,0.219 10 false 1 4.083,1.292 4.26,1.531 0.177,0.24 10 false 2 0.26,1.073 0.427,1.292 0.167,0.219 10 false 1 0.271,0.656 0.417,0.885 0.146,0.229 10 false 2

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system, take safety precautions to prevent electrical shocks, such as wearing insulated gloves and removing the service plug grip. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION

HINT:

At least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:

After repairing, restart the system (turn the power switch on (READY)) and recheck for DTCs.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>DTC CHECK / CLEAR


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (IGCT VOLTAGE)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the rear side seatback assembly LH.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY>REMOVAL


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG).


e.
A260174C10
0.281,1.01 0.708,1.313 0.427,0.302 1.323,1.229 0.823,0.615 true 1.323,1.302 0.521,2.5 true 0.094,0.073 0.396,0.365 0.302,0.292 10 false *a 0.333,2.521 0.677,2.76 0.344,0.24 10 false GND 0.49,0.542 0.875,0.76 0.385,0.219 10 false IGCT 0.375,1.052 0.646,1.271 0.271,0.219 10 false N18
*a Component with harness connected
(Battery Smart Unit)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N18-3 (IGCT) - N18-6 (GND) Power switch on (IG) 11 to 14 V


NOTICE:

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.



f.

Turn the power switch off.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

Install the rear side seatback assembly LH.


Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (GND - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (GND - BODY GROUND)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the rear side seatback assembly LH.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY>REMOVAL


c.
A260174C09
0.271,1 0.698,1.313 0.427,0.313 1.333,1.302 0.385,2.469 true 0.135,0.125 0.417,0.365 0.281,0.24 10 false *a 0.229,2.531 0.594,2.771 0.365,0.24 10 false GND 0.354,1.042 0.646,1.281 0.292,0.24 10 false N18
*a Component with harness connected
(Battery Smart Unit)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
N18-6 (GND) - Body ground Power switch off Below 1 Ω



d.

Install the rear side seatback assembly LH.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATT VL SSR FUSE - BATTERY SMART UNIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND - BODY GROUND)