Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM › from 2015.04
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074886 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  U029A-123  Lost Communication with Hybrid Battery Pack Sensor Module  


DESCRIPTION

The battery smart unit detects the HV battery conditions (voltage, current, and temperature) and battery cooling fan voltage, and sends the detected signals to the power management control ECU via serial communication.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
U029A-123 Lost Communication with Hybrid Battery Pack Sensor Module Problem in serial communication between the battery smart unit and power management control ECU (1 trip detection)
·

Wire harness or connector

·

Power management control ECU

·

Battery smart unit


Comes on Master Warning Light:
Comes on

WIRING DIAGRAM

A260754E17
0.844,0.74 1.75,0.969 0.906,0.229 10 false IGCT-MAIN 0.458,1.229 1.177,1.458 0.719,0.229 10 false R/B NO. 2 3.063,1.208 3.5,1.49 0.438,0.281 10 false IGCT 4.958,0.729 5.865,0.99 0.906,0.26 10 false BATT VL SSR 2.802,0.406 2.948,0.573 0.146,0.167 10 false 3 2.792,0.781 2.938,0.948 0.146,0.167 10 false 2 3.531,0.781 3.677,0.948 0.146,0.167 10 false 1 3.531,0.396 3.677,0.563 0.146,0.167 10 false 5 5.74,0.479 5.885,0.646 0.146,0.167 10 false 3 5.708,3.573 5.875,3.75 0.167,0.177 10 false 1 5.917,0.563 6.417,0.792 0.5,0.229 10 false IGCT 5.917,3.688 6.323,3.917 0.406,0.229 10 false BTH+ 5.917,4.135 6.292,4.365 0.375,0.229 10 false BTH- 5.719,4.01 5.865,4.281 0.146,0.271 10 false 4 5.917,6.385 6.292,6.615 0.375,0.229 10 false GND 5.521,7.01 5.896,7.24 0.375,0.229 10 false N18 5.729,6.25 5.875,6.417 0.146,0.167 10 false 6 3.75,3.677 4.156,3.906 0.406,0.229 10 false BTH+ 3.771,4.125 4.146,4.354 0.375,0.229 10 false BTH- 4.292,3.938 4.542,4.104 0.25,0.167 10 false 29 4.292,3.479 4.542,3.646 0.25,0.167 10 false 30 3.719,1.896 4.125,2.125 0.406,0.229 10 false MREL 3.833,2.458 4.24,2.688 0.406,0.229 10 false +B1 3.833,2.979 4.24,3.208 0.406,0.229 10 false +B2 3.292,1.917 3.698,2.146 0.406,0.229 10 false AM22 3.281,2.49 3.688,2.719 0.406,0.229 10 false AM21 1.063,2.104 1.469,2.333 0.406,0.229 10 false AM2 2.969,1.708 3.219,1.917 0.25,0.208 10 false 1 2.979,2.281 3.167,2.51 0.188,0.229 10 false 7 4.333,1.698 4.479,1.865 0.146,0.167 10 false 4 4.333,2.271 4.479,2.438 0.146,0.167 10 false 3 4.333,2.76 4.479,2.927 0.146,0.167 10 false 1 2.531,7.01 4.656,7.24 2.125,0.229 10 false Power Management Control ECU 5.844,7.021 7.063,7.25 1.219,0.229 10 false Battery Smart Unit 3.854,6.469 4.229,6.698 0.375,0.229 10 false E01 2.958,1.917 3.177,2.083 0.219,0.167 10 false I3 4.333,6.271 4.479,6.438 0.146,0.167 10 false 5 2.958,2.469 3.24,2.635 0.281,0.167 10 false I4 4.24,1.896 4.521,2.125 0.281,0.229 10 false A38 0.552,6.042 2.479,6.281 1.927,0.24 10 false Combination Meter Assembly 2.042,6.458 2.448,6.74 0.406,0.281 10 false ECM 0.677,2.521 1.333,2.823 0.656,0.302 10 false IG2-MAIN 1.094,3.719 1.448,3.906 0.354,0.188 10 false IG2 1.292,5.156 2.458,5.354 1.167,0.198 10 false ACC NO. 1 Relay 1.354,5.615 2.5,5.854 1.146,0.24 10 false IG1 NO. 3 Relay 2.917,6.458 3.198,6.688 0.281,0.229 10 false A38 2.979,2.854 3.125,3.021 0.146,0.167 10 false 1 2.99,4.979 3.135,5.146 0.146,0.167 10 false 1 2.99,5.417 3.135,5.583 0.146,0.167 10 false 2 2.979,3.281 3.125,3.448 0.146,0.167 10 false 2 2.948,5.854 3.198,6.021 0.25,0.167 10 false 16 2.938,6.271 3.188,6.438 0.25,0.167 10 false 19 3.292,3.063 3.667,3.292 0.375,0.229 10 false IG2 3.281,5.177 3.75,5.406 0.469,0.229 10 false ACCD 3.281,5.635 3.75,5.865 0.469,0.229 10 false IG1D 3.281,3.49 3.75,3.719 0.469,0.229 10 false IG2D 3.292,6.063 3.76,6.292 0.469,0.229 10 false SPDI 3.281,6.469 3.75,6.698 0.469,0.229 10 false GI 4.24,2.458 4.552,2.688 0.313,0.229 10 false A39 2.906,3.063 3.208,3.292 0.302,0.229 10 false A39 2.906,3.479 3.177,3.708 0.271,0.229 10 false A39 4.24,2.99 4.552,3.219 0.313,0.229 10 false A38 4.292,3.688 4.458,3.854 0.167,0.167 10 false I3 4.292,4.125 4.458,4.292 0.167,0.167 10 false I3 4.302,6.458 4.469,6.625 0.167,0.167 10 false I3 2.958,6.052 3.177,6.219 0.219,0.167 10 false I3 2.958,5.177 3.24,5.344 0.281,0.167 10 false I4 2.969,5.625 3.25,5.792 0.281,0.167 10 false I4 5.031,1.5 5.729,1.708 0.698,0.208 10 false PM IGCT 1.958,3.26 2.979,3.521 1.021,0.26 10 false ECU-IG2 NO. 1 0.458,4.521 1.052,4.771 0.594,0.25 10 false MAIN 0.583,5.01 1.167,5.406 0.583,0.396 10 false Auxiliary Battery 5.146,0.469 5.292,0.635 0.146,0.167 10 false 1 5.49,0.458 5.635,0.625 0.146,0.167 10 false 2 0.979,0.427 1.125,0.594 0.146,0.167 10 false 1 1.313,0.417 1.458,0.583 0.146,0.167 10 false 2 0.969,1.76 1.115,1.927 0.146,0.167 10 false 1 1.365,1.771 1.51,1.938 0.146,0.167 10 false 2 0.448,2.333 0.594,2.5 0.146,0.167 10 false 1 0.438,2.771 0.583,2.938 0.146,0.167 10 false 2 2.208,2.885 2.354,3.052 0.146,0.167 10 false 1 2.542,2.885 2.688,3.052 0.146,0.167 10 false 2 4.802,1.208 4.948,1.375 0.146,0.167 10 false 1 4.802,1.677 4.99,1.885 0.188,0.208 10 false 2 0.802,4.083 2.354,4.323 1.552,0.24 10 false No. 1 Integration Relay 1.75,3.49 1.969,3.667 0.219,0.177 10 false 1C 1.74,3.042 1.958,3.219 0.219,0.177 10 false 1C 0.51,3.063 0.729,3.24 0.219,0.177 10 false 1D 0.521,3.479 0.74,3.656 0.219,0.177 10 false 1E 0.573,3.292 0.719,3.458 0.146,0.167 10 false 2 0.635,2.875 0.781,3.042 0.146,0.167 10 false 3 1.781,3.292 1.927,3.458 0.146,0.167 10 false 8 1.792,2.875 1.938,3.042 0.146,0.167 10 false 5

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system, take safety precautions to prevent electrical shocks, such as wearing insulated gloves and removing the service plug grip. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION

HINT:

At least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.

Powertrain > Hybrid Control > Trouble Codes
50001 236

d.

Check for DTCs.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>DTC CHECK / CLEAR

Result:
Result Proceed to
Only U029A-123 is output. A
DTCs other than U029A-123 are also output. B



e.

Turn the power switch off.


f.

Disconnect the intelligent tester from the DLC3.



A

2.CHECK BATTERY SMART UNIT (IGCT VOLTAGE)

B

2.CHECK BATTERY SMART UNIT (IGCT VOLTAGE)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the rear side seatback assembly LH.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY>REMOVAL


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG).


e.
A260174C10
0.281,1.01 0.708,1.313 0.427,0.302 1.323,1.229 0.823,0.615 true 1.323,1.302 0.521,2.5 true 0.094,0.073 0.396,0.365 0.302,0.292 10 false *a 0.333,2.521 0.677,2.76 0.344,0.24 10 false GND 0.49,0.542 0.875,0.76 0.385,0.219 10 false IGCT 0.375,1.052 0.646,1.271 0.271,0.219 10 false N18
*a Component with harness connected
(Battery Smart Unit)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N18-3 (IGCT) - N18-6 (GND) Power switch on (IG) 11 to 14 V


NOTICE:

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.


HINT:

As there might be an intermittent malfunction in the battery smart unit power source circuit, inspect the following even if the measured voltage is as specified:

·

Installation condition of fuse(s) (before removing fuse(s)) (IGCT circuit)

·

Fuse condition (before and after removing fuse(s)) (IGCT circuit)

·

Connection condition of connectors (IGCT circuit)

·

Wire harness condition (IGCT circuit)

·

Wire harness condition (GND circuit)




f.

Turn the power switch off.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

Install the rear side seatback assembly LH.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BATTERY SMART UNIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY SMART UNIT POWER SOURCE CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BATTERY SMART UNIT)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect connector I3 from the power management control ECU.

Click herePower Source / Network>POWER DISTRIBUTION>POWER MANAGEMENT CONTROL ECU>REMOVAL


c.

Remove the rear side seatback assembly LH.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY>REMOVAL


d.

Disconnect connector N18 from the battery smart unit.


e.

Measure the resistance according to the value(s) in the table below.

A306415C07
1.229,1.469 1.615,1.729 0.385,0.26 4.688,1.552 5.083,1.833 0.396,0.281 4.99,2.396 5.51,2.167 true 2.719,2.313 2.344,1.854 true 1.865,2.281 2.302,1.854 true 5.74,2.042 6.26,1.813 true 5.771,2.167 6.24,2.385 true 2.615,2.344 3,2.583 0.385,0.24 10 false BTH- 0.5,0.156 0.813,0.313 0.313,0.156 10 false *a 4.573,0.24 4.885,0.396 0.313,0.156 10 false *b 1.375,1.5 1.573,1.677 0.198,0.177 10 false I3 1.677,2.323 2.063,2.563 0.385,0.24 10 false BTH+ 4.771,1.615 5.125,1.844 0.354,0.229 10 false N18 4.625,2.333 4.979,2.615 0.354,0.281 10 false GND 6.313,1.729 6.833,2.031 0.521,0.302 10 false BTH+ 6.292,2.323 6.677,2.563 0.385,0.24 10 false BTH-
*a Rear view of wire harness connector
(to Power Management Control ECU)
*b Rear view of wire harness connector
(to Battery Smart Unit)


Standard Resistance:
Tester Connection Switch Condition Specified Condition
I3-30 (BTH+) - N18-1 (BTH+) Power switch off Below 1 Ω
I3-29 (BTH-) - N18-4 (BTH-) Power switch off Below 1 Ω
N18-1 (BTH+) - N18-6 (GND) and Body ground Power switch off 10 kΩ or higher
N18-4 (BTH-) - N18-6 (GND) and Body ground Power switch off 10 kΩ or higher



f.
A258634C08
1.531,0.677 0.719,1.042 true 0.063,0.021 0.323,0.198 0.26,0.177 10 false *1 0.531,0.99 0.719,1.167 0.188,0.177 10 false *2
*1 No. 2 Engine Room Relay Block
*2 PM IGCT Fuse


Remove the PM IGCT fuse from the No. 2 engine room relay block.


g.
A256541C05
3.031,1.292 2.344,1.104 true 0.396,0.115 0.729,0.375 0.333,0.26 10 false *1 3.073,1.229 3.333,1.406 0.26,0.177 10 false *2
*1 Engine Room Relay Block and Junction Block Assembly
*2 AM2 Fuse


Remove the AM2 fuse from the engine room relay block and junction block assembly.


h.
A265460C05
1.938,1.771 2.573,1.979 true 0.208,0.146 0.458,0.365 0.25,0.219 10 false *1 2.615,1.917 2.885,2.177 0.271,0.26 10 false *2
*1 Instrument Panel Junction Block Assembly
*2 ECU-IG2 NO. 1 Fuse


Remove the ECU-IG2 No. 1 fuse from the instrument panel junction block assembly.


i.

Disconnect all connectors from the power management control ECU.


j.

Measure the resistance according to the value(s) in the table below.

A245299C20
2.51,0.917 2.906,1.156 0.396,0.24 3.125,0.917 3.521,1.156 0.396,0.24 3.792,0.906 4.188,1.146 0.396,0.24 4.417,0.917 4.813,1.156 0.396,0.24 2.677,1.51 1.344,2.083 true 2.844,1.5 1.646,2.344 true 2.813,1.615 1.99,2.448 true 3.344,1.521 2.406,2.479 true 3.458,1.521 2.802,2.49 true 3.51,1.521 3.156,2.479 true 3.781,1.573 3.615,2.5 true 4.125,1.51 5.073,2.49 true 4.438,1.51 5.51,2.375 true 4.719,1.51 5.979,2.208 true 4.771,1.51 6.208,1.823 true 4.125,1.688 4.5,2.49 true 4.083,1.688 4,2.469 true 2.583,0.958 2.906,1.156 0.323,0.198 10 false A38 1.365,2.333 1.635,2.51 0.271,0.177 10 false +B2 1.854,2.458 2.073,2.667 0.219,0.208 10 false GI 2.198,2.51 2.469,2.688 0.271,0.177 10 false +B1 0.625,0.25 0.781,0.427 0.156,0.177 10 false *a 3.198,0.948 3.479,1.156 0.281,0.208 10 false A39 3.948,0.948 4.167,1.125 0.219,0.177 10 false I3 4.958,2.51 5.354,2.688 0.396,0.177 10 false AM22 5.458,2.406 5.865,2.583 0.406,0.177 10 false AM21 0.906,2.042 1.313,2.188 0.406,0.146 10 false MREL 3.063,2.521 3.302,2.719 0.24,0.198 10 false IG2 6.292,1.76 6.708,1.938 0.417,0.177 10 false ACCD 2.635,2.521 2.99,2.729 0.354,0.208 10 false IG2D 3.458,2.531 3.802,2.688 0.344,0.156 10 false SPDI 5.969,2.25 6.313,2.427 0.344,0.177 10 false IG1D 4.563,0.948 4.781,1.125 0.219,0.177 10 false I4 4.406,2.521 4.802,2.729 0.396,0.208 10 false BTH- 3.885,2.521 4.281,2.729 0.396,0.208 10 false BTH+
*a Rear view of wire harness connector
(to Power Management Control ECU)
- -


Standard Resistance:
Tester Connection Switch Condition Specified Condition
I3-30 (BTH+) - I4-7 (AM21) Power switch off 10 kΩ or higher
I3-30 (BTH+) - I3-1 (AM22) Power switch off 10 kΩ or higher
I3-30 (BTH+) - A38-1 (+B2) Power switch off 10 kΩ or higher
I3-30 (BTH+) - A39-3 (+B1) Power switch off 10 kΩ or higher
I3-30 (BTH+) - A38-4 (MREL) Power switch off 10 kΩ or higher
I3-30 (BTH+) - A39-1 (IG2) Power switch off 10 kΩ or higher
I3-30 (BTH+) - I4-1 (ACCD) Power switch off 10 kΩ or higher
I3-30 (BTH+) - I4-2 (IG1D) Power switch off 10 kΩ or higher
I3-30 (BTH+) - A39-2 (IG2D) Power switch off 10 kΩ or higher
I3-30 (BTH+) - I3-16 (SPDI) Power switch off 10 kΩ or higher
I3-30 (BTH+) - A38-19 (GI) Power switch off 10 kΩ or higher
I3-29 (BTH-) - I4-7 (AM21) Power switch off 10 kΩ or higher
I3-29 (BTH-) - I3-1 (AM22) Power switch off 10 kΩ or higher
I3-29 (BTH-) - A38-1 (+B2) Power switch off 10 kΩ or higher
I3-29 (BTH-) - A39-3 (+B1) Power switch off 10 kΩ or higher
I3-29 (BTH-) - A38-4 (MREL) Power switch off 10 kΩ or higher
I3-29 (BTH-) - A39-1 (IG2) Power switch off 10 kΩ or higher
I3-29 (BTH-) - I4-1 (ACCD) Power switch off 10 kΩ or higher
I3-29 (BTH-) - I4-2 (IG1D) Power switch off 10 kΩ or higher
I3-29 (BTH-) - A39-2 (IG2D) Power switch off 10 kΩ or higher
I3-29 (BTH-) - I3-16 (SPDI) Power switch off 10 kΩ or higher
I3-29 (BTH-) - A38-19 (GI) Power switch off 10 kΩ or higher


NOTICE:

When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.



k.

Connect the power management control ECU connectors.


l.

Install the ECU-IG2 NO. 1 fuse to the instrument panel junction block assembly.


m.

Install the AM2 fuse to the engine room relay block and junction block assembly.


n.

Install the PM IGCT fuse to the No. 2 engine room relay block.


o.

Connect the battery smart unit connector.


p.

Install the rear side seatback assembly LH.


Result:
Proceed to
OK
NG



OK

4.CHECK POWER MANAGEMENT CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK POWER MANAGEMENT CONTROL ECU
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the rear side seatback assembly LH.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY>REMOVAL


c.

Disconnect connector N18 from the battery smart unit.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG).


f.
A260173C09
0.917,1.906 1.344,2.25 0.427,0.344 1.927,2.344 2.427,2 true 2.521,2.969 1.927,2.552 true 1.073,2.906 1.573,2.563 true 2.479,1.896 2.885,2.146 0.406,0.25 10 false BTH+ 2.573,2.917 3,3.167 0.427,0.25 10 false BTH- 0.75,2.865 1.083,3.115 0.333,0.25 10 false GND 0.677,0.156 0.885,0.396 0.208,0.24 10 false *a 1,2.01 1.281,2.24 0.281,0.229 10 false N18
*a Rear view of wire harness connector
(to Battery Smart Unit)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N18-1 (BTH+) - N18-6 (GND) Power switch on (IG) 2.3 to 2.7 V
N18-4 (BTH-) - N18-6 (GND) Power switch on (IG) 2.3 to 2.7 V


NOTICE:

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.



g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.


i.
A260173C10
0.844,2.167 1.271,2.427 0.427,0.26 1.927,2.354 2.417,2.021 true 2.542,2.948 1.927,2.563 true 2.479,1.927 2.896,2.177 0.417,0.25 10 false BTH+ 2.573,2.875 3.01,3.125 0.438,0.25 10 false BTH- 0.75,0.219 1.063,0.563 0.313,0.344 10 false *a 0.927,2.188 1.219,2.385 0.292,0.198 10 false N18
*a Rear view of wire harness connector
(to Battery Smart Unit)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
N18-1 (BTH+) - N18-4 (BTH-) Power switch off 4.4 to 5.4 kΩ


HINT:

Resistance becomes 2.0 kΩ or less when there is a short circuit in the power management control ECU.



j.

Connect the battery smart unit connector.


k.

Install the rear side seatback assembly LH.


Result:
Proceed to
OK
NG



OK

NG