Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2015.04
RM2040EQ _59 Vehicle Exterior _014738 LIGHTING (EXT) _0075173 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Headlight Dimmer Switch Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) receives the following switch information:

·

Light control switch is in off, tail, head or AUTO position

·

Dimmer switch is in high, low or high flash (pass) position


WIRING DIAGRAM

E312379E03
3.302,1.073 3.615,1.271 0.313,0.198 10 false HL 3.74,1.083 4.052,1.281 0.313,0.198 10 false HU 4.198,1.083 4.51,1.281 0.313,0.198 10 false HF 2.813,1.073 3.125,1.271 0.313,0.198 10 false EL 2.219,1.438 2.719,1.677 0.5,0.24 10 false Flash 2.25,1.823 2.563,2.021 0.313,0.198 10 false Low 2.25,2.219 2.563,2.417 0.313,0.198 10 false High 1.427,1.458 1.948,1.948 0.521,0.49 10 false Dimmer Switch 4.75,0.396 5.063,0.594 0.313,0.198 10 false HU 4.76,0.729 5.073,0.927 0.313,0.198 10 false HF 5.021,0.396 5.333,0.594 0.313,0.198 10 false 17 5.01,0.729 5.323,0.927 0.313,0.198 10 false 14 6.073,0.406 6.385,0.604 0.313,0.198 10 false 5 6.063,0.719 6.375,0.917 0.313,0.198 10 false 8 6.229,0.49 6.542,0.688 0.313,0.198 10 false HU 6.24,0.823 6.552,1.021 0.313,0.198 10 false HF 6.229,2.958 6.729,3.188 0.5,0.229 10 false HEAD 6.24,2.646 6.552,2.844 0.313,0.198 10 false TAIL 6.25,3.292 6.563,3.49 0.313,0.198 10 false A 6.01,3.167 6.323,3.365 0.313,0.198 10 false 28 6.01,2.875 6.323,3.073 0.313,0.198 10 false 29 6.01,2.573 6.323,2.771 0.313,0.198 10 false 30 5.51,4.031 5.823,4.229 0.313,0.198 10 false I13 5.49,4.198 7.115,4.854 1.625,0.656 10 false Main Body ECU (Multiplex Network Body ECU) 5.031,3.177 5.344,3.375 0.313,0.198 10 false 11 5.01,2.875 5.323,3.073 0.313,0.198 10 false 12 5.01,2.563 5.323,2.781 0.313,0.219 10 false 13 4.802,2.563 5.115,2.76 0.313,0.198 10 false T 4.792,2.875 5.104,3.073 0.313,0.198 10 false H 4.781,3.177 5.094,3.375 0.313,0.198 10 false A 4.125,3.656 4.438,3.854 0.313,0.198 10 false A 3.698,3.656 4.01,3.854 0.313,0.198 10 false H 3.26,3.656 3.573,3.854 0.313,0.198 10 false T 2.708,3.646 3.021,3.844 0.313,0.198 10 false EL 2.063,5.25 2.521,5.448 0.458,0.198 10 false AUTO 2.188,4 2.5,4.198 0.313,0.198 10 false Off 2.146,4.479 2.458,4.677 0.313,0.198 10 false Tail 2.094,4.865 2.49,5.094 0.396,0.229 10 false Head 1.146,4.292 1.948,4.677 0.802,0.385 10 false Light Control Switch 0.333,5.698 0.646,5.896 0.313,0.198 10 false 16 0.573,5.698 0.885,5.896 0.313,0.198 10 false EL 0.625,6.281 0.938,6.479 0.313,0.198 10 false I25 0.625,6.427 3.104,6.656 2.479,0.229 10 false Headlight Dimmer Switch Assembly

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Dimmer SW Dimmer switch high position signal ON or OFF ON: Dimmer switch in high or high flash position
OFF: Dimmer switch in low position
-
Passing Light SW Dimmer switch high flash position (pass) signal ON or OFF ON: Dimmer switch in high flash position
OFF: Dimmer switch not in high flash position
-
Auto Light SW Light control switch AUTO position signal ON or OFF ON: Light control switch in AUTO position
OFF: Light control switch not in AUTO position
-
Head Light SW (Head) Light control switch head position signal ON or OFF ON: Light control switch in head position
OFF: Light control switch not in head position
-
Head Light SW (Tail) Light control switch tail position signal ON or OFF ON: Light control switch in tail or head position
OFF: Light control switch in neither tail nor head position
-
Body Electrical > Main Body > Data List
Tester Display
Dimmer SW
Passing Light SW
Auto Light SW
Head Light SW (Head)
Head Light SW (Tail)
50003 123 54,55,58,59,60
OK:

Normal conditions listed above are displayed.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY
2.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY
HINT:

Inspect the items that did not change as a result of monitoring the Data List.


a.

Remove the headlight dimmer switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT DIMMER SWITCH>REMOVAL


b.
E295730C55
1.396,1.844 1.521,1.406 false 2.063,1.844 2.042,1.396 false 2.354,1.854 2.198,1.406 false 2.344,1.396 2.594,1.833 false 1.729,1.854 1.698,1.406 false 2.583,1.365 2.99,1.365 false 0.167,0.125 0.479,0.281 0.313,0.156 10 false *a 1.302,1.885 1.646,2.104 0.344,0.219 10 false HU 1.656,1.875 2,2.094 0.344,0.219 10 false EL 1.979,1.875 2.323,2.094 0.344,0.219 10 false HF 2.323,1.875 2.51,2.104 0.188,0.229 10 false T 2.573,1.875 2.76,2.104 0.188,0.229 10 false H 3.052,1.271 3.365,1.427 0.313,0.156 10 false A
*a Component without harness connected
(Headlight Dimmer Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Light Control Switch
Tester Connection Condition Specified Condition
13 (T) - 16 (EL) Light control switch off 10 kΩ or higher
12 (H) - 16 (EL) Light control switch off 10 kΩ or higher
11 (A) - 16 (EL) Light control switch off 10 kΩ or higher
13 (T) - 16 (EL) Light control switch in tail position Below 1 Ω
13 (T) - 16 (EL) Light control switch in head position Below 1 Ω
12 (H) - 16 (EL) Light control switch in head position Below 1 Ω
11 (A) - 16 (EL) Light control switch in AUTO position Below 1 Ω

Dimmer Switch
Tester Connection Condition Specified Condition
17 (HU) - 16 (EL) Dimmer switch in low position 10 kΩ or higher
17 (HU) - 16 (EL) Dimmer switch in high position Below 1 Ω
14 (HF) - 16 (EL) Dimmer switch in high flash position Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - HEADLIGHT DIMMER SWITCH ASSEMBLY)

NG

REPLACE HEADLIGHT DIMMER SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - HEADLIGHT DIMMER SWITCH ASSEMBLY)
a.

Disconnect the I13 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I25-17 (HU) - I13-5 (HU) Always Below 1 Ω
I25-14 (HF) - I13-8 (HF) Always Below 1 Ω
I25-13 (T) - I13-30 (TAIL) Always Below 1 Ω
I25-12 (H) - I13-29 (HEAD) Always Below 1 Ω
I25-11 (A) - I13-28 (A) Always Below 1 Ω
I25-17 (HU) - Body ground Always 10 kΩ or higher
I25-14 (HF) - Body ground Always 10 kΩ or higher
I25-13 (T) - Body ground Always 10 kΩ or higher
I25-12 (H) - Body ground Always 10 kΩ or higher
I25-11 (A) - Body ground Always 10 kΩ or higher
I25-16 (EL) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR