Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2015.04
RM2040EQ _59 Vehicle Exterior _014738 LIGHTING (EXT) _0075173 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Low Beam Headlight Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the low beam headlights.

WIRING DIAGRAM

E315840E02
0.125,0.698 1.01,1.188 0.885,0.49 10 false from Auxiliary Battery 1.396,0.906 2.313,1.125 0.917,0.219 10 false H-LP-MAIN 3.458,1.26 3.917,1.479 0.458,0.219 10 false H-LP 4.292,1.094 5.917,1.677 1.625,0.583 10 false Instrument Panel Junction Block Assembly 4.802,0.729 5.083,0.938 0.281,0.208 10 false 3D 4.802,0.531 5.083,0.74 0.281,0.208 10 false 12 5.719,0.615 6,0.823 0.281,0.208 10 false 15 6,0.729 6.458,0.948 0.458,0.219 10 false HRLY 5.469,2.573 7.146,3 1.677,0.427 10 false Main Body ECU (Multiplex Network Body ECU) 5.469,2.406 5.927,2.625 0.458,0.219 10 false MB 3.208,2.594 4.115,2.823 0.906,0.229 10 false H-LP LH-LO 3.229,4.573 4.135,4.802 0.906,0.229 10 false H-LP RH-LO 0.938,3.021 1.281,3.208 0.344,0.188 10 false A78 0.938,3.177 2.521,3.417 1.583,0.24 10 false Headlight Assembly LH 0.917,4.99 1.26,5.177 0.344,0.188 10 false A80 0.927,5.125 2.51,5.365 1.583,0.24 10 false Headlight Assembly RH 1.417,2.667 2.333,2.885 0.917,0.219 10 false Low Beam 1.427,4.646 2.344,4.865 0.917,0.219 10 false Low Beam 3.146,0.615 3.375,0.844 0.229,0.229 10 false 2 3.958,0.604 4.188,0.833 0.229,0.229 10 false 1 3.958,0.865 4.188,1.094 0.229,0.229 10 false 3 3.156,0.865 3.385,1.094 0.229,0.229 10 false 5 2.302,2.333 2.563,2.552 0.26,0.219 10 false LO 2.583,2.333 2.813,2.563 0.229,0.229 10 false 2 0.802,2.323 1.031,2.552 0.229,0.229 10 false 3 2.594,4.302 2.823,4.531 0.229,0.229 10 false 2 0.802,4.292 1.031,4.521 0.229,0.229 10 false 3 1.01,2.323 1.24,2.552 0.229,0.229 10 false E 0.979,4.292 1.208,4.521 0.229,0.229 10 false E 2.302,4.302 2.573,4.51 0.271,0.208 10 false LO

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Active Test.


e.

Perform the Active Test according to the display on the intelligent tester.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Headlight Relay Headlight relay (low beam headlights) ON/OFF -
Body Electrical > Main Body > Active Test
Tester Display
Headlight Relay
50004 123 14
OK:

Headlight relay operates. (Low beam headlights illuminate.)



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT H-LP RELAY
2.INSPECT H-LP RELAY
a.

Remove the H-LP relay from the engine room relay block and junction block assembly.


b.
E209495C10
0.135,0.0 0.461,0.269 0.327,0.269 10 *a
*a Component without harness connected
(H-LP Relay)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Voltage not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Voltage applied between terminals 1 and 2 Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURSE - H-LP RELAY)

NG

REPLACE H-LP RELAY

3.CHECK HARNESS AND CONNECTOR (POWER SOURSE - H-LP RELAY)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Relay Terminal 2 - Body ground Power switch off 11 to 14 V
Relay Terminal 5 - Body ground Power switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (H-LP RELAY - HEADLIGHT ASSEMBLY LH AND HEADLIGHT ASSEMBLY RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (H-LP RELAY - HEADLIGHT ASSEMBLY LH AND HEADLIGHT ASSEMBLY RH)
a.

Disconnect the A78 headlight assembly LH connector.


b.

Disconnect the A80 headlight assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Relay Terminal 3 - A78-2 (LO) Always Below 1 Ω
Relay Terminal 3 - A80-2 (LO) Always Below 1 Ω
Relay Terminal 3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (H-LP RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (H-LP RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3D instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Relay Terminal 1 - 3D-12 Always Below 1 Ω
Relay Terminal 1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.
E182506C02
1.479,0.771 1.969,1.063 0.49,0.292 1.479,2.938 1.969,3.229 0.49,0.292 1.594,3.49 1.594,3.75 false 0.156,0.156 0.938,0.813 0.781,0.656 10 *a 1.625,0.823 2.427,1.354 0.802,0.531 10 3D 1.594,2.99 2.344,3.458 0.75,0.469 10 MB 1.365,3.76 2.438,4.344 1.073,0.583 10 HRLY
*a Component without harness connected
(Instrument Panel Junction Block Assembly)


Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3D-12 - MB-15 (HRLY) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY