Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM(w/o Parallel Parking Assist Function) › from 2014.05
RM2040EQ _56 Audio / Visual / Telematics _014718 PARK ASSIST / MONITORING _0169414 PARKING ASSIST MONITOR SYSTEM(w/o Parallel Parking Assist Function) C

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM(w/o Parallel Parking Assist Function)  C1622  Back Camera Disconnected  


DESCRIPTION

This DTC is stored if the navigation receiver assembly judges that the signals or signal lines between the rear television camera assembly, and the navigation receiver assembly are not normal as a result of its self check.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1622 Back Camera Disconnected Open or short in the rear television camera assembly signal circuit
·

Harness or connector

·

Rear television camera assembly

·

Navigation receiver assembly



WIRING DIAGRAM

E267063E46
2.302,0.531 2.625,0.74 0.323,0.208 10 false 11 2.25,1.115 2.708,1.313 0.458,0.198 10 false I174 2.26,1.51 2.719,1.708 0.458,0.198 10 false I174 2.26,1.906 2.719,2.104 0.458,0.198 10 false I174 2.302,2.302 2.76,2.5 0.458,0.198 10 false I64 1.865,0.708 2.323,0.906 0.458,0.198 10 false CA+ 1.948,1.094 2.406,1.292 0.458,0.198 10 false V+ 1.979,1.5 2.24,1.698 0.26,0.198 10 false V- 1.729,1.896 2.25,2.115 0.521,0.219 10 false CGND 1.75,2.302 2.271,2.521 0.521,0.219 10 false GND1 2.302,0.927 2.625,1.135 0.323,0.208 10 false 12 2.313,1.333 2.635,1.542 0.323,0.208 10 false 24 2.302,1.729 2.625,1.938 0.323,0.208 10 false 23 2.26,0.719 2.823,0.927 0.563,0.208 10 false I174 0.958,2.656 2.198,3.01 1.24,0.354 10 false Navigation Receiver Assembly 2.344,2.125 2.667,2.333 0.323,0.208 10 false 7 4.833,0.615 5.156,0.823 0.323,0.208 10 false 6 4.833,1 5.156,1.208 0.323,0.208 10 false 3 4.833,1.406 5.135,1.625 0.302,0.219 10 false 2 4.823,1.802 5.146,2.01 0.323,0.208 10 false 5 5.021,0.708 5.479,0.906 0.458,0.198 10 false CB+ 5.021,1.115 5.479,1.313 0.458,0.198 10 false CV+ 5.031,1.51 5.5,1.75 0.469,0.24 10 false CV- 5.021,1.896 5.542,2.115 0.521,0.219 10 false CGND 4.833,2.219 5.292,2.417 0.458,0.198 10 false T22 4.833,2.385 6.333,2.917 1.5,0.531 10 false Rear Television Camera Assembly 3.302,3.125 5.135,3.323 1.833,0.198 10 false *: Shielded 3.5,1.688 3.813,1.885 0.313,0.198 10 false *

CAUTION / NOTICE / HINT

NOTICE:
·

If the cable was disconnected from and reconnected to the negative (-) auxiliary battery terminal, the estimated course lines may not be displayed on the image of the area behind the vehicle. In this case, perform "Correct the Steering Angle Neutral Point".

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(w/o Parallel Parking Assist Function)>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(w/o Parallel Parking Assist Function)>CALIBRATION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the I174 navigation receiver assembly connector.


b.

Disconnect the T22 rear television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I174-11 (CA+) - T22-6 (CB+) Always Below 1 Ω
I174-12 (V+) - T22-3 (CV+) Always Below 1 Ω
I174-24 (V-) - T22-2 (CV-) Always Below 1 Ω
I174-23 (CGND) - T22-5 (CGND) Always Below 1 Ω
I174-11 (CA+) - Body ground Always 10 kΩ or higher
I174-12 (V+) - Body ground Always 10 kΩ or higher
I174-24 (V-) - Body ground Always 10 kΩ or higher
I174-23 (CGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT NAVIGATION RECEIVER ASSEMBLY (CA+, CGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT NAVIGATION RECEIVER ASSEMBLY (CA+, CGND)
a.

Reconnect the I174 navigation receiver assembly connector.


b.
E271917C78
1.521,0.188 1.969,0.479 0.448,0.292 1.115,1.792 1.229,1.313 false 0.906,0.771 1.219,1.125 false 1.615,0.25 2,0.438 0.385,0.188 10 false I174 0.906,1.833 1.531,2.063 0.625,0.229 10 false CGND 0.604,0.625 1.229,0.854 0.625,0.229 10 false CA+ 0.115,0.073 0.74,0.302 0.625,0.229 10 false *a
*a Component with harness connected
(Navigation receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I174-23 (CGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I174-11 (CA+) - I174-23 (CGND) Power switch on (ACC) 5.5 to 7.05 V



Result:
Proceed to
OK
NG



OK

3.INSPECT NAVIGATION RECEIVER ASSEMBLY (V+, GND1)

NG

3.INSPECT NAVIGATION RECEIVER ASSEMBLY (V+, GND1)
a.

Reconnect the T22 rear television camera assembly connector.


b.
E279721C46
1.479,0.208 1.896,0.5 0.417,0.292 1.479,2.396 1.927,2.677 0.448,0.281 0.729,0.823 1.115,1.198 false 1.854,3.698 2.5,4.188 false 0.094,0.083 0.438,0.25 0.344,0.167 10 false *a 2.521,4.219 2.948,4.396 0.427,0.177 10 false GND1 1.563,0.271 1.906,0.438 0.344,0.167 10 false I174 1.594,2.448 2.073,2.688 0.479,0.24 10 false I64 0.51,0.688 0.854,0.854 0.344,0.167 10 false V+
*a Component with harness connected
(Navigation receiver Assembly)


E265840C05
0.823,2.073 1,2.073 1,2.073 1.125,1.583 false 1.479,2.063 1.344,2.063 1.344,2.063 1.229,1.479 false 0.781,4.167 0.958,4.167 0.958,4.167 1.156,3.594 false 1.521,4.125 1.385,4.125 1.385,4.125 1.271,3.542 false 0.229,0.229 0.542,0.427 0.313,0.198 10 *a 0.396,1.052 0.76,1.313 0.365,0.26 10 GND 0.396,3.208 0.76,3.469 0.365,0.26 10 GND 0.26,2.271 0.625,2.531 0.365,0.26 10 *b 0.646,4.073 1.01,4.333 0.365,0.26 10 *c 0.656,1.979 1.021,2.24 0.365,0.26 10 *c 1.51,1.969 1.875,2.229 0.365,0.26 10 *d 1.542,4.052 1.906,4.313 0.365,0.26 10 *d
*a Waveform 1 (camera lens is not covered, displaying an image)
*b Waveform 2 (camera lens is covered, blacking out the screen)
*c Synchronization Signal
*d Video Waveform


Using an oscilloscope, check the waveform of the rear television camera assembly.

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly with the connector connected.


OK:

Waveform is similar to that shown in the illustration.

Item Content
Measurement terminal I174-12 (V+) - I64-7 (GND1)
Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Power switch on (IG), shift lever in R


HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the power switch is on (ACC).




Result:
Proceed to
OK
NG



OK

NG

REPLACE REAR TELEVISION CAMERA ASSEMBLY