Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM(for 4 Sensor Type) › from 2015.04
RM2040EQ _56 Audio / Visual / Telematics _014718 PARK ASSIST / MONITORING _0169417 TOYOTA PARKING ASSIST-SENSOR SYSTEM(for 4 Sensor Type) J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM(for 4 Sensor Type)  Clearance Warning Buzzer Circuit  


DESCRIPTION

This circuit consists of the No. 1 clearance warning buzzer and clearance warning ECU assembly. An ECU-excited type buzzer is used. The ECU operates the buzzer using a sound pattern that changes depending on the distance to the obstacle.

WIRING DIAGRAM

E220929E06
1.981,1.356 2.076,1.509 0.096,0.154 10 1 3.27,1.356 3.365,1.509 0.096,0.154 10 2 1.639,2.024 1.920,2.178 0.281,0.154 10 I54 1.639,2.192 3.696,2.346 2.056,0.154 10 No. 1 Clearance Warning Buzzer 4.203,2.024 4.484,2.178 0.281,0.154 10 I82 4.203,2.192 6.383,2.346 2.180,0.154 10 Clearance Warning ECU Assembly 4.694,0.619 4.867,0.773 0.173,0.154 10 14 4.952,0.705 5.239,0.859 0.288,0.154 10 BBZ 4.694,1.356 4.867,1.509 0.173,0.154 10 13 4.952,1.442 5.163,1.596 0.211,0.154 10 ER 2.135,1.356 2.331,1.509 0.196,0.154 10 Z+ 3.06,1.356 3.214,1.509 0.155,0.154 10 Z-

PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Clearance Sonar / Active Test.


e.

Check that the buzzer operates by performing the Active Test.

Body Electrical > Clearance Sonar > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Buzzer No. 1 clearance warning buzzer Operate or Stop Confirm that the vehicle is stopped and the power switch is on (IG)
Body Electrical > Clearance Sonar > Active Test
Tester Display
Buzzer
50004 170 4
OK:

The No. 1 clearance warning buzzer sounds.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - NO. 1 CLEARANCE WARNING BUZZER)
2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - NO. 1 CLEARANCE WARNING BUZZER)
a.

Disconnect the I54 No. 1 clearance warning buzzer connector.


b.

Disconnect the I82 clearance warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I82-14 (BBZ) - I54-1 (Z+) Always Below 1 Ω
I82-13 (ER) - I54-2 (Z-) Always Below 1 Ω
I82-14 (BBZ) - Body ground Always 10 kΩ or higher
I82-13 (ER) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE NO. 1 CLEARANCE WARNING BUZZER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE NO. 1 CLEARANCE WARNING BUZZER
a.

Replace the No. 1 clearance warning buzzer with a new or known good one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE WARNING BUZZER>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.PERFORM ACTIVE TEST USING GTS
4.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Clearance Sonar / Active Test.


e.

Check that the buzzer operates by performing the Active Test.

Body Electrical > Clearance Sonar > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Buzzer No. 1 clearance warning buzzer Operate or Stop Confirm that the vehicle is stopped and the power switch is on (IG)
Body Electrical > Clearance Sonar > Active Test
Tester Display
Buzzer
50004 170 4
OK:

The No. 1 clearance warning buzzer sounds.



Result:
Proceed to
OK
NG



OK

END (NO. 1 CLEARANCE WARNING BUZZER WAS DEFECTIVE)

NG