Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for SD) › from 2014.05
RM2040EQ _56 Audio / Visual / Telematics _014717 NAVIGATION / MULTI INFO DISPLAY _0169499 NAVIGATION SYSTEM(for SD) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for SD)  B15D3  Stereo Component Amplifier Disconnected  


DESCRIPTION

The navigation receiver assembly and stereo component amplifier assembly are connected via AVC-LAN communication lines.

This DTC is stored when an AVC-LAN communication error occurs between the navigation receiver assembly and stereo component amplifier assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15D3 Stereo Component Amplifier Disconnected When either of the following conditions is met:
·

The stereo component amplifier assembly is/was not connected while the power switch is/was on (ACC) or on (IG)

·

Communication between the master unit and the stereo component amplifier assembly is not possible when the engine is started


·

Stereo component amplifier assembly power source circuit

·

AVC-LAN circuit between navigation receiver assembly and stereo component amplifier assembly

·

Stereo component amplifier assembly

·

Navigation receiver assembly

·

Harness or connector



HINT:

The navigation receiver assembly is the master unit.


WIRING DIAGRAM

E286987E07
0.063,0.51 1.563,0.781 1.5,0.271 10 false from Auxiliary Battery 0.313,1.24 1.354,1.688 1.042,0.448 10 false from ACC NO. 1 Relay 2.948,0.688 3.979,0.969 1.031,0.281 10 false AMP 2.813,1.385 3.844,1.667 1.031,0.281 10 false ECU-ACC 5.25,0.521 5.583,0.74 0.333,0.219 10 false I68 5.24,1.219 5.573,1.438 0.333,0.219 10 false I69 5.24,2.135 5.573,2.354 0.333,0.219 10 false I69 5.24,2.521 5.573,2.74 0.333,0.219 10 false I69 5.24,3.208 5.573,3.427 0.333,0.219 10 false I68 2.438,2.948 2.771,3.167 0.333,0.219 10 false I67 2.438,3.135 4.5,3.75 2.063,0.615 10 false Navigation Receiver Assembly 5.594,0.521 5.927,0.74 0.333,0.219 10 false +B 5.594,1.229 5.927,1.448 0.333,0.219 10 false ACC 5.604,2.135 5.938,2.354 0.333,0.219 10 false TX+ 5.615,2.531 5.948,2.75 0.333,0.219 10 false TX- 5.594,3.208 5.927,3.427 0.333,0.219 10 false GND 3.219,2.135 3.604,2.385 0.385,0.25 10 false TX1+ 3.24,2.531 3.573,2.75 0.333,0.219 10 false TX1- 5.292,0.323 5.625,0.542 0.333,0.219 10 false 1 5.26,1.031 5.594,1.25 0.333,0.219 10 false 12 5.302,1.927 5.635,2.146 0.333,0.219 10 false 8 5.302,2.344 5.635,2.563 0.333,0.219 10 false 7 5.302,2.99 5.635,3.208 0.333,0.219 10 false 3 1.156,4.188 3.896,4.5 2.74,0.313 10 false : AVC-LAN Communication Line 5.469,4.021 6.667,4.625 1.198,0.604 10 false Stereo Component Amplifier Assembly 3.625,2.01 3.958,2.229 0.333,0.219 10 false 7 3.625,2.406 3.958,2.625 0.333,0.219 10 false 8

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK DTC
a.

If DTC B15C3 is output, perform troubleshooting for DTC B15C3 first.

Result:
Result Proceed to
DTC B15C3 is not output. A
DTC B15C3 is output. B




A

2.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

2.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Check that optional components (including associated wiring) which generate radio waves are not installed.

Result:
Result Proceed to
Optional components (including associated wiring) are installed. A
Optional components (including associated wiring) are not installed. B


HINT:
·

Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.

·

This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.





A

3.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

4.CHECK DTC
3.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Remove optional components (including associated wiring).

NOTICE:

Do not remove optional components or associated wiring without the permission of the customer.



Result:
Proceed to
NEXT



NEXT

4.CHECK DTC
4.CHECK DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for SD)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG

5.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY POWER SOURCE)
5.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY POWER SOURCE)
a.

Disconnect the I68 and I69 stereo component amplifier assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I68-3 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I68-1 (+B) - I68-3 (GND) Power switch off 11 to 14 V
I69-12 (ACC) - I68-3 (GND) Power switch on (ACC) 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the I67 navigation receiver assembly connector.


b.

Disconnect the I69 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I67-7 (TX1+) - I69-8 (TX+) Always Below 1 Ω
I67-8 (TX1-) - I69-7 (TX-) Always Below 1 Ω
I67-7 (TX1+) - Body ground Always 10 kΩ or higher
I67-8 (TX1-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY
a.

Replace the stereo component amplifier assembly with a new or known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>STEREO COMPONENT AMPLIFIER>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for SD)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG