Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for SD) › from 2014.05
RM2040EQ _56 Audio / Visual / Telematics _014717 NAVIGATION / MULTI INFO DISPLAY _0169499 NAVIGATION SYSTEM(for SD) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for SD)  Microphone Circuit between Microphone and Navigation Receiver Assembly  


DESCRIPTION

The navigation receiver assembly and roof console box assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

Using this circuit, the navigation receiver assembly sends power to the roof console box assembly (telephone microphone assembly), and the roof console box assembly (telephone microphone assembly) sends microphone signals to the navigation receiver assembly.

WIRING DIAGRAM

E268499E50
0.802,0.802 1.302,0.969 0.5,0.167 10 false MACC 0.823,1.271 1.323,1.438 0.5,0.167 10 false MCO+ 0.844,1.74 1.344,1.906 0.5,0.167 10 false MCO- 0.854,2.698 1.271,2.865 0.417,0.167 10 false SNS2 0.167,3.156 0.563,3.323 0.396,0.167 10 false S12 0.167,3.323 2.667,3.708 2.5,0.385 10 false Roof Console Box Assembly (Telephone Microphone Assembly) 3.281,2.083 4.052,2.292 0.771,0.208 10 false (Shielded) 5.927,0.802 6.427,0.969 0.5,0.167 10 false MACC 5.927,1.271 6.344,1.438 0.417,0.167 10 false MIN+ 5.927,1.75 6.26,1.917 0.333,0.167 10 false MIN- 5.927,2.229 6.427,2.396 0.5,0.167 10 false SGND 5.927,2.698 6.344,2.865 0.417,0.167 10 false SNS2 5.677,3.125 6.063,3.292 0.385,0.167 10 false I67 5.677,3.302 6.906,3.74 1.229,0.438 10 false Navigation Receiver Assembly 1.333,0.698 1.583,0.875 0.25,0.177 10 false 14 1.333,1.167 1.615,1.344 0.281,0.177 10 false 13 1.333,1.646 1.615,1.823 0.281,0.177 10 false 12 1.333,2.594 1.5,2.76 0.167,0.167 10 false 15 5.74,0.698 5.906,0.865 0.167,0.167 10 false 4 5.74,1.167 5.906,1.333 0.167,0.167 10 false 5 5.74,2.594 5.906,2.76 0.167,0.167 10 false 6 5.667,1.646 5.917,1.813 0.25,0.167 10 false 19 5.667,2.125 5.917,2.292 0.25,0.167 10 false 18

PROCEDURE

1.CHECK MICROPHONE (OPERATION CHECK)
a.
E268457

Enter the "Microphone Check" screen. Refer to Check Microphone in Operation Check.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for SD)>OPERATION CHECK


b.

When a voice is input into the microphone, check that the microphone input level meter changes according to the input voice.


c.

Push the recording switch and perform voice recording.

HINT:
·

Select the recording switch with the blower motor of the air conditioning system stopped. If an outlet of the air conditioning system is facing the microphone, noise may be recorded.

·

Voice can be recorded for up to 5 seconds.




d.

Check that the recording indicator remains on while recording and that the recorded voice is played normally without noise or distortion.

OK:

All check results are normal.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
a.

Disconnect the I67 navigation receiver assembly connector.


b.

Disconnect the S12 roof console box assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I67-6 (SNS2) - S12-15 (SNS2) Always Below 1 Ω
I67-4 (MACC) - S12-14 (MACC) Always Below 1 Ω
I67-5 (MIN+) - S12-13 (MCO+) Always Below 1 Ω
I67-19 (MIN-) - S12-12 (MCO-) Always Below 1 Ω
I67-6 (SNS2) - Body ground Always 10 kΩ or higher
I67-4 (MACC) - Body ground Always 10 kΩ or higher
I67-5 (MIN+) - Body ground Always 10 kΩ or higher
I67-19 (MIN-) - Body ground Always 10 kΩ or higher
I67-18 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT NAVIGATION RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT NAVIGATION RECEIVER ASSEMBLY
a.

Reconnect the I67 navigation receiver assembly connector.


b.

Reconnect the S12 roof console box assembly (telephone microphone assembly) connector.


c.
E289390C10
1.427,0.656 1.802,0.896 0.375,0.24 2.073,2 1.448,2.906 false 2.219,2 2.771,2.875 false 2.24,1.771 2.76,0.979 false 0.125,0.115 0.438,0.313 0.313,0.198 10 false *a 1.521,0.698 1.833,0.896 0.313,0.198 10 false I67 1.26,2.969 1.771,3.229 0.51,0.26 10 false MIN- 2.604,2.948 3.115,3.208 0.51,0.26 10 false SGND 2.802,0.844 3.313,1.104 0.51,0.26 10 false MACC
*a Component with harness connected
(Navigation Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I67-4 (MACC) - Body ground Power switch on (ACC) 4 to 6 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I67-18 (SGND) - Body ground Always Below 1 Ω
I67-19 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

4.INSPECT ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Remove the roof console box assembly (telephone microphone assembly).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.
E187117C49
1.542,1.74 1.771,1.365 false 2.281,1.729 2.104,1.375 false 2.229,1.75 2.844,1.948 0.615,0.198 10 false MCO- 1.177,1.75 1.792,1.948 0.615,0.198 10 false SNS2 0.115,0.104 0.427,0.302 0.313,0.198 10 false *a
*a Component without harness connected
(Roof Console Box Assembly (Telephone Microphone Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
12 (MCO-) - 15 (SNS2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

REPLACE ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

5.INSPECT ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Reconnect the I67 navigation receiver assembly connector.


b.

Reconnect the S12 roof console box assembly (telephone microphone assembly) connector.


c.

Turn the power switch on (ACC).


d.
E187122C61
0.333,1.75 0.75,2 0.417,0.25 2.01,2.198 1.604,1.292 false 2.125,2.208 2.406,1.292 false 0.146,0.115 0.479,0.344 0.333,0.229 10 false *a 1.302,1.083 1.781,1.281 0.479,0.198 10 false MCO+ 2.375,1.094 2.979,1.271 0.604,0.177 10 false MCO- 0.427,1.781 0.906,1.979 0.479,0.198 10 false S12
*a Component with harness connected
(Roof Console Box Assembly (Telephone Microphone Assembly))


Connect an oscilloscope to terminals 13 (MCO+) and 12 (MCO-) of the S12 roof console box assembly (telephone microphone assembly) connector.


e.

Check the waveform of the roof console box assembly (telephone microphone assembly) using the oscilloscope.

Result:
Result Proceed to
A waveform synchronized with the voice input to the roof console box assembly (telephone microphone assembly) is output. A
A waveform synchronized with the voice input to the roof console box assembly (telephone microphone assembly) is not output. B




A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

6.REPLACE TELEPHONE MICROPHONE ASSEMBLY
6.REPLACE TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly with a new or known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE>REMOVAL


b.

Check if the same malfunction recurs.

Result:
Result Proceed to
Malfunction does not recur (returns to normal). A
Malfunction recurs. B




A

END

B

REPLACE ROOF CONSOLE BOX ASSEMBLY