Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2015.04
RM2040EQ _57 Power Source / Network _014721 NETWORKING _0075042 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Power Management Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Power Management Control ECU Communication Stop Mode
·

"Power Management1" and/or "Hybrid Vehicle Control" is not displayed on the Communication Bus Check screen of the intelligent tester.

Click here(Click here)

·

Applies to Power Management Control ECU Communication Stop Mode in DTC Combination Table.

Click here(Click here)


·

Power management control ECU branch line or connector

·

Power source circuit of power management control ECU

·

Power management control ECU



WIRING DIAGRAM

C256537E07
5.354,0.5 5.25,0.5 5.25,0.5 4.948,1.094 false 2.344,2.594 2.344,3.771 2.344,3.771 2.042,3.771 false 6.302,2.625 6.76,2.854 0.458,0.229 10 false ECM 1.979,0.385 2.49,0.708 0.51,0.323 10 false DLC3 6.083,3.74 7,4.031 0.917,0.292 10 false Trouble Area 0.167,0.198 0.865,0.594 0.698,0.396 12 false V Bus: 0.563,2.615 1.74,3.292 1.177,0.677 10 false Combination Meter Assembly 5.427,0.417 6.583,0.854 1.156,0.438 10 false CAN Junction LH1 Connector 0.844,3.677 2,4.229 1.156,0.552 10 false CAN Junction RH1 Connector 3.51,4.094 5.76,4.5 2.25,0.406 10 false Power Management Control ECU 3.521,3.75 3.844,3.979 0.323,0.229 10 false A38 3.531,3.406 3.823,3.583 0.292,0.177 10 false A39 4.271,3.083 4.5,3.26 0.229,0.177 10 false I4 2.698,3.927 3.354,4.177 0.656,0.25 10 false PM IGCT 4.156,3.26 4.583,3.552 0.427,0.292 10 false CA1H 4.583,3.26 5,3.448 0.417,0.188 10 false CA1L 3.865,3.385 4.24,3.563 0.375,0.177 10 false +B1 3.875,3.74 4.271,3.948 0.396,0.208 10 false +B2 5.031,3.594 5.313,3.844 0.281,0.25 10 false E1 5.354,3.396 5.563,3.635 0.208,0.24 10 false 6 3.615,3.219 3.771,3.396 0.156,0.177 10 false 3 3.615,3.583 3.813,3.823 0.198,0.24 10 false 1 3.979,3.083 4.167,3.333 0.188,0.25 10 false 25 4.948,3.083 5.229,3.365 0.281,0.281 10 false 24 6.167,2.021 6.646,2.271 0.479,0.25 10 false 120 Ω 0.688,2.042 1.219,2.333 0.531,0.292 10 false 120 Ω 1.438,4.917 3.354,5.24 1.917,0.323 10 false : CAN Main Bus Line (CANH) 1.438,5.323 3.354,5.646 1.917,0.323 10 false : CAN Main Bus Line (CANL) 4.406,4.927 6.167,5.25 1.76,0.323 10 false : CAN Branch Line (CANH) 4.406,5.333 6.146,5.656 1.74,0.323 10 false : CAN Branch Line (CANL) 5.354,3.594 5.594,3.771 0.24,0.177 10 false I3 4.677,3.083 4.906,3.26 0.229,0.177 10 false I4 0.302,2.615 0.625,2.854 0.323,0.24 10 false I18 6,2.625 6.323,2.854 0.323,0.229 10 false A25

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), wait at least 60 seconds and then drive the vehicle at a speed of 36 km/h (22 mph) or more for at least 7 seconds.

·

After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK CAN BUS LINE FOR DISCONNECTION (POWER MANAGEMENT CONTROL ECU BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
A204446C41
3.01,2.24 3.323,2.469 0.313,0.229 2.469,2.5 2.083,2.188 false 2.427,2.5 2.073,2.5 false 3.104,2.26 3.292,2.479 0.188,0.219 10 false I4 1.646,2.427 2.156,2.656 0.51,0.229 10 false CA1H 1.698,2.042 2.146,2.271 0.448,0.229 10 false CA1L 0.156,0.073 0.542,0.396 0.385,0.323 10 false *a
*a Rear view of wire harness connector
(to Power Management Control ECU)


Disconnect the power management control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Value
I4-25 (CA1H) - I4-24 (CA1L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (POWER MANAGEMENT CONTROL ECU)

2.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)
a.

Reconnect the power management control ECU connector (I4).


b.

Disconnect the power management control ECU connector (I3).


c.
A204445C84
2,2.948 2.25,3.188 0.25,0.24 1.823,2.365 1.656,2.146 false 2.073,2.969 2.281,3.146 0.208,0.177 10 false I3 0.146,0.052 0.656,0.302 0.51,0.25 10 false *a 1.479,1.99 1.802,2.26 0.323,0.271 10 false E1
*a Rear view of wire harness connector
(to Power Management Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Value
I3-6 (E1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



Result:
Result
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND TERMINAL)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.

Reconnect the power management control ECU connector.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.
A251057C09
0.635,0.896 1.083,1.177 0.448,0.281 1.198,0.896 1.656,1.167 0.458,0.271 0.688,2.396 0.99,1.698 true 1.25,2.406 1.458,1.698 true 0.344,0.26 0.656,0.458 0.313,0.198 10 false *a 0.708,0.948 1.167,1.146 0.458,0.198 10 false A38 1.281,0.938 1.74,1.135 0.458,0.198 10 false A39 0.542,2.448 1.073,2.719 0.531,0.271 10 false +B2 1.115,2.458 1.583,2.708 0.469,0.25 10 false +B1
*a Component with harness connected
(Power Management Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Value
A39-3 (+B1) - Body ground Power switch on (IG) 11 to 14 V
A38-1 (+B2) - Body ground Power switch on (IG) 11 to 14 V



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE TERMINAL)