ECUS OR SENSORS WHICH COMMUNICATE THROUGH CAN COMMUNICATION SYSTEM
V Bus
ECM
Brake booster with master cylinder assembly (Skid control ECU)
Main body ECU (Multiplex network body ECU)
Air conditioning amplifier assembly
Power steering ECU assembly
Smart key ECU assembly (Certification ECU)
Airbag sensor assembly
Steering sensor
Power management control ECU
Combination meter assembly
Navigation receiver assembly*1
Radio and display receiver assembly*2
Clearance warning ECU assembly*3
Sub Bus 1*4
Main body ECU (Multiplex network body ECU)
Outer mirror control ECU assembly (for Driver side)
Outer mirror control ECU assembly (for Front passenger side)
Position control ECU and switch assembly (for Driver side)
Sub Bus 11
Power management control ECU
Blind spot monitor sensor RH*5
Rear television camera assembly*6
Lane departure warning camera*7
Driving support ECU assembly*8
Sub Bus 13*8
Driving support ECU assembly
Millimeter wave radar sensor assembly
Sub Bus 15
ECM
Power management control ECU
Brake booster with master cylinder assembly (Skid control ECU)
*1: for Navigation Receiver Type
*2: for Radio and Display Type
*3: w/ Toyota Parking Assist-sensor System
*4: w/ Seat Position Memory System
*5: w/ Blind Spot Monitor System
*6: w/ Parking Assist Monitor System without Parallel Parking Assist Function
*7: w/ Lane Departure Alert System
*8: w/ Pre-crash Safety System
CHECK FOR INSTALLED SYSTEMS (ECUS AND SENSORS) THAT ADOPT CAN COMMUNICATION
The systems (ECUs and sensors) that adopt CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs and sensors) are installed to the vehicle.
| ECU/Sensor Name | GTS Display | Applicability |
|---|---|---|
| ECM | ECM (Engine) | Installed on all vehicles |
| Brake booster with master cylinder assembly (Skid control ECU) | Skid Control (ABS/VSC/TRAC) | Installed on all vehicles |
| Main body ECU (Multiplex network body ECU) | Main Body | Installed on all vehicles |
| Air conditioning amplifier assembly | Air Conditioning Amplifier | Installed on all vehicles |
| Power steering ECU assembly | Power Steering (EPS) | Installed on all vehicles |
| Smart key ECU assembly (Certification ECU) | Certification (Smart) | Installed on all vehicles |
| Airbag sensor assembly | Airbag | Installed on all vehicles |
| Steering sensor | Spiral cable (Steering Angle Sensor) | Installed on all vehicles |
| Power management control ECU | ·
Power management1 ·
Hybrid Vehicle Control |
Installed on all vehicles |
| Combination meter assembly | Combination Meter | Installed on all vehicles |
| Navigation receiver assembly | Display and Navigation (AVN1) | Vehicles with navigation receiver type |
| Radio and display receiver assembly | Display and Navigation (AVN1) | Vehicles with radio and display type |
| Outer mirror control ECU assembly (for Driver side) | Front Door RH/R-Mirror (FR-Door2/R-Miror) | Vehicles with seat position memory system |
| Outer mirror control ECU assembly (for Front passenger side) | Front Door LH/L-Mirror (FL-Door2/L-Miror) | Vehicles with seat position memory system |
| Position control ECU and switch assembly (for Driver side) | D-Seat | Vehicles with seat position memory system |
| Blind spot monitor sensor RH | Blind Spot Monitor Master | Vehicles with blind spot monitor system |
| Rear television camera assembly | Parking Assist Monitor System3 | Vehicles with parking assist monitor system without parallel parking assist function |
| Clearance warning ECU assembly | Clearance Warning (Clearance Sonar2) | Vehicles with Toyota parking assist-sensor system |
| Lane departure warning camera | Front Camera Module | Vehicles with lane departure alert system |
| Driving support ECU assembly | Driving Support (Cruise Control-ACC) | Vehicles with pre-crash safety system |
| Millimeter wave radar sensor assembly | - | Vehicles with pre-crash safety system |
The names of ECUs and sensors shown on the GTS display may differ from those shown in the DTC Table by ECU section.
CAN BUS CHECK
The ECUs and sensors that are properly connected to the CAN communication system can be displayed using the GTS.
Using the GTS, select the CAN Bus Check screen.
It may be possible to select buses that do not have ECUs or sensors from the bus selection pull-down menu. This is not a malfunction. (This occurs when optional devices are not on a sub bus that is monitored by a gateway function equipped ECU.)
In the bus selection pull down menu, all buses applicable to the model are displayed (e.g. LIN communication buses are also displayed). Therefore, refer to the wiring diagrams to check the names of sub buses for CAN communication.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>SYSTEM DIAGRAM
Different connection statuses are indicated by the background color of ECUs and sensors that are displayed.
| Bus Type | Background Color | Connection Status |
|---|---|---|
| V Bus | White | Communication has been normal since the start of the CAN bus check. |
| Yellow | Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication). | |
| Red | Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring (unstable communication). | |
| Not displayed | Communication stop has continued since the start of the CAN bus check.*1 | |
| Sub Bus
(gateway function equipped ECU that does not have history of connected ECUs)*2 |
White | Communication has been normal since the start of the CAN bus check. |
| Yellow | Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication). | |
| Red | Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring (unstable communication). | |
| Not displayed | Communication stop has continued since the start of the CAN bus check.*1 | |
| Sub Bus
(gateway function equipped ECU that has history of connected ECUs)*3 |
White | Communication has been normal since the start of the CAN bus check. |
| Yellow | Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication). | |
| Red | Currently not communicating (either of the following):
·
Communication stop has continued since the start of the CAN bus check. ·
Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring. |
|
| Not displayed | Either of the following:
·
If a gateway function equipped ECU cannot communicate, the sub bus and ECUs connected to the sub bus will not be displayed. ·
If no ECUs are connected to the sub bus, "There is no system found on the Communication Bus" will be displayed. |
Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
*1: ECUs that are present in the vehicle but are not displayed on the CAN Bus Check screen.
*2: Gateway function equipped ECU that does not memorize the sub bus ECUs that are connected to it.
*3: Gateway function equipped ECU that memorizes the sub bus ECUs that are connected to it.
If none of the connected ECUs are displayed, or there is no response from the vehicle to the GTS, check the DLC3 branch and the V bus main bus lines for a malfunction.
Observe the connection response screen for approximately 2 minutes to check for a change in connection status of the connected ECUs and sensors.
If an open occurs in one of the lines of a CAN branch (except DLC3), output from the other branch line (the line that is not open) will be unstable and it may interfere with the response (display) of other ECUs and sensors.
If the connection status changes during the inspection, repair the open in the branch line of the ECU or sensor that does not respond (is not detected) and then perform the CAN bus check again.
HOW TO INTERPRET CAN BUS CHECK SCREEN
When a communication stop is currently occurring, the probable malfunctioning part can be determined from the CAN bus check and by using the following methods.
The following CAN bus wiring diagram is provided only as an example. This wiring diagram is different from the actual wiring diagram for this vehicle.
When a communication stop is currently occurring, it is easier to determine the probable malfunctioning part from the CAN bus check rather than from communication DTCs.
Wait for approximately 2 minutes after turning the power switch on (IG) (or simulate the driving conditions that enable the malfunction to be reproduced) and select "CAN Bus Check". Then observe the communication status of each ECU on the screen.
If a communication error of only 1 ECU or sensor is indicated on the CAN Bus Check screen, a communication stop of the ECU or sensor is suspected.
Example: Open in both CAN branch lines of ECU B on the V bus
| *a | V Bus | *b | Sub Bus |
| *c | Terminating Resistor | *d | Location of Malfunction |
| *e | Not displayed or background color changes to red or yellow | *f | CAN Bus Check Screen |
When there are communication stops, ECUs are present in the vehicle even though they are not displayed on the CAN Bus Check screen.
| *a | Background color periodically changes to yellow or red |
| *b | Not displayed or background color is yellow or red |
| *c | Not displayed |
If communication errors for multiple ECUs or sensors are indicated on the CAN Bus Check screen, then a communication stop of the ECU or sensor that shows a more serious communication stop (an ECU or sensor which is not displayed) is suspected.
Example: Open in a CAN branch line for ECU D on the V bus
| Bus Type | Background Color | Connection Status |
|---|---|---|
| V Bus | White | Communication has been normal since the start of the CAN bus check. |
| Yellow | Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication). | |
| Red | Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring (unstable communication). | |
| Not displayed | Communication stop has continued since the start of the CAN bus check.*1 | |
| Sub Bus
(gateway function equipped ECU that does not have history of connected ECUs)*2 |
White | Communication has been normal since the start of the CAN bus check. |
| Yellow | Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication). | |
| Red | Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring (unstable communication). | |
| Not displayed | Communication stop has continued since the start of the CAN bus check.*1 | |
| Sub Bus
(gateway function equipped ECU that has history of connected ECUs)*3 |
White | Communication has been normal since the start of the CAN bus check. |
| Yellow | Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication). | |
| Red | Currently not communicating (either of the following):
·
Communication stop has continued since the start of the CAN bus check. ·
Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring. |
|
| Not displayed | Either of the following:
·
If a gateway function equipped ECU cannot communicate, the sub bus and ECUs connected to the sub bus will not be displayed. ·
If no ECUs are connected to the sub bus, "There is no system found on the Communication Bus" will be displayed. |
Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
*1: ECUs that are present in the vehicle but are not displayed on the CAN Bus Check screen.
*2: Gateway function equipped ECU that does not memorize the sub bus ECUs that are connected to it.
*3: Gateway function equipped ECU that memorizes the sub bus ECUs that are connected to it.
The example of the CAN Bus Check screen in the illustration shows the result of electrical noise on the CAN bus which is caused by an open in a CAN branch line of ECU D (output from the other branch line is unstable) and the communication of ECU C is also unstable. In addition, in this example, ECU C is equipped with a gateway function. Therefore, communication is also unstable between the sub bus ECUs of ECU C and the V bus.
The example in the illustration shows that ECU D is not displayed on the CAN Bus Check screen. This indicates a more significant communication stop. In this case, a communication stop of ECU D is suspected.
| *a | Not displayed or background color changes to red |
If a communication error is indicated on both the V bus and sub bus on the CAN Bus Check screen, suspect any communication stop displayed for the V bus first.
Example: Open in both CAN branch lines of ECU C on the V bus
In the CAN bus check, it is possible to confirm the communication status of ECUs connected to the V bus after connecting the GTS to the DLC3. As for sub buses, it is possible to confirm which sub bus connected ECUs can communicate with a gateway function equipped ECU on the V bus.
If a gateway function equipped ECU has a communication error, ECUs connected to the gateway function equipped ECU are also affected, and communication stops will be indicated.
The CAN Bus Check screen in the illustration shows that ECU C has a gateway function and a communication stop in ECU C is suspected.
| *a | Background color changes to red |
If the CAN Bus Check screen indicates a communication stop only in the sub bus, a communication stop in the sub bus is suspected.
Example: Open in both CAN branch lines of ECU G on the sub bus
A communication error in a sub bus does not affect the V bus or other buses.
When a gateway function equipped ECU has memorized the ECUs that are connected to the sub bus, if any of the ECUs connected to the gateway function equipped ECU has a communication error, the background color changes to yellow or red. (The displayed name will not disappear.)
If both of the V bus main bus lines are open, ECUs or sensors that are located farther away from the DLC3 than the open part will be displayed as a communication stop on the CAN Bus Check screen.
(In this case, ECU A and B are not displayed or their background color changes to red.)
| *a | V Bus | *b | Sub Bus |
| *c | Terminating Resistor | *d | Location of Malfunction |
| *e | Not displayed or background color is red | *f | CAN Bus Check Screen |
If a communication error occurs in an ECU, it is not displayed on the CAN Bus Check screen even though the ECU is present.
If both of the sub bus main bus lines are open, ECUs that are located farther away from the gateway function equipped ECU than the open part will be displayed as a communication stop on the CAN Bus Check screen.
(In this case, ECU I and J are not displayed or their background color changes to red.)
| *a | V Bus | *b | Sub Bus |
| *c | Terminating Resistor | *d | Location of Malfunction |
| *e | Not displayed or background color is red | *f | CAN Bus Check Screen |
| *g | Gateway Function Equipped ECU | - | - |
| *a | When any of the following malfunctions occur on the V bus |
| *b | When any of the following malfunctions occur on a sub bus |
| *c | Not displayed |
When any of the following malfunctions occur, CAN communication cannot be established and almost all ECUs and sensors on the bus show a communication error on the CAN Bus Check screen.
| Short between CAN lines (CANH and CANL) |
| Short between a CAN line (CANH or CANL) and +B |
| Short between a CAN line (CANH or CANL) and ground |
| Open in a CAN main bus line |
When a malfunction occurs on the V bus, almost all ECUs and sensors on the V bus and sub bus indicate a communication error (almost all ECUs are not displayed). As communication with the gateway function equipped ECU that is connected to the V bus stops, communication from the ECUs connected to the sub bus that is monitored by the gateway function equipped ECU also stops (these ECUs are not displayed).
When a malfunction occurs in a sub bus, almost all ECUs connected to the sub bus indicate a communication error.
A communication error in a sub bus does not affect the V bus or other buses.
The malfunctioning part can be determined by checking for a short circuit between CAN bus lines or between a CAN bus line and ground or +B short using an electrical tester.
HOW TO INTERPRET COMMUNICATION DTCS (DTCS THAT START WITH U)
If a CAN communication error cannot be reproduced, determine the suspected malfunctioning part using the DTCs stored in ECUs that are connected to the CAN buses by following the procedure below.
Communication DTCs (DTCs that start with U) indicate a communication error between the ECU that stores the DTC and the ECU that is indicated by the DTC.
If multiple ECUs store a communication DTC for a particular ECU, a communication stop of the ECU is suspected.
| *a | Items to be Checked | - | - |
This DTC table is from another model, and is only used here to show an example of DTCs that are output when there is an open in a CAN branch line for the main body ECU. This table does not show DTCs applicable to this vehicle.
Even though a DTC title may indicate a communication error with a specific ECU, the ECU name used in the DTC name on the GTS may differ depending on the ECU that stores the DTC. (Regarding output DTCs, refer to step 6 and the DTC chart for each ECU.)
As multiple ECUs indicate a communication stop with the main body ECU, the possibility of a communication stop of the main body ECU is high.
If almost all of the communication DTCs of an ECU are stored, a communication stop of the ECU is suspected.
| *a | Items to be Checked | - | - |
This DTC table is from another model, and is only used here to show an example of DTCs that are output when there is an open in a CAN branch line for the main body ECU. This table does not show DTCs applicable to this vehicle.
If almost all of the DTCs of the main body ECU are stored, the possibility of a communication stop of the main body ECU is high.
When a CAN communication error occurs, many DTCs are output. DTCs other than communication error DTCs (such as DTCs that start with C or B) and communication DTCs for the ABS system are important DTCs, however it may be easier to determine the malfunctioning part by examining the overall situation without considering these DTCs.
To help determine the part of the sub bus that has a communication error, prioritize the communication stop DTCs stored in the gateway function equipped ECU.
| *a | Items to be Checked | *b | ECM |
| *c | Gateway Function Equipped ECU | *d | Location of Malfunction |
| *e | V Bus | *f | Sub Bus |
This DTC table is from another model, and is only used here to show the ECUs connected to both a V bus and a sub bus. It shows DTCs output when there is an open in the main bus lines for the ECM on the sub bus. This table does not show DTCs applicable to this vehicle.
As gateway function equipped ECUs (sub bus monitor ECU) monitor signals from all ECUs that are connected to sub buses, gateway function equipped ECUs can detect ECUs with a communication stop more accurately.
When there is a communication stop for the gateway function equipped ECU (gateway), communication with ECUs connected to other buses such as the V bus stops. Therefore, communication DTCs for ECUs connected to other buses are also stored.
When any of the following malfunctions occurs, many DTCs are likely to be output from many ECUs. Because of this, it may be difficult to determine the probable malfunctioning part.
Short between CAN lines (CANH and CANL)
Short between a CAN line (CANH or CANL) and ground
Short between a CAN line (CANH or CANL) and +B
Open in a CAN branch line (CANH or CANL) of an ECU or sensor
Open in a CAN main bus line (CANH or CANL) between 2 ECUs that have a terminating resistor
DTC TABLE BY ECU
In the CAN communication system, the CAN communication DTCs of each ECU can be displayed using the GTS.
If CAN communication system DTCs are output, the malfunction cannot be determined only by the DTCs. Perform troubleshooting according to How to Proceed with Troubleshooting.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
If the system function temporarily returns to normal, DTCs may not be output again even though the following DTC check procedures are used.
Power Management Control ECU / GTS Display "Hybrid Control"
This ECU uses the CAN communication system for DTC communication.
*1: Refer to Hybrid Control System.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
*2: Refer to Hybrid Battery System.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
*3: Refer to Dynamic Radar Cruise Control System.
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>U0235
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication with ECM / PCM "A" | The power management control ECU (HV CPU) does not receive data from the ECM for 0.58 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the power management control ECU is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 1.58 seconds. | ·
Master warning light turns on. ·
MIL illuminates. |
DTC is stored until it is cleared using the GTS. |
| U0110*1 | Lost Communication with Drive Motor Control Module "A" | Either condition is met:
1.
The power management control ECU (HV CPU) does not receive data from the inverter with converter assembly (MG ECU) for 0.11 seconds or more. 2.
The power management control ECU (HV CPU) does not send data to the inverter with converter assembly (MG ECU) for 0.04 seconds or more. |
Both conditions are met:
·
The power switch is on (IG) for 0.1 seconds or more. ·
The power source voltage of the power management control ECU is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 0.21 seconds. | Master warning light turns on. | DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Brake System Control Module | The power management control ECU (HV CPU) does not receive data from the brake booster with master cylinder assembly (skid control ECU) for 2.34 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 2.1 seconds or more. ·
The power source voltage of the power management control ECU is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 4.44 seconds. | Master warning light turns on. | DTC is stored until it is cleared using the GTS. |
| U0140 | Communication Error from Body ECU to HV ECU | The power management control ECU (HV CPU) does not receive data from the main body ECU (multiplex network body ECU) for 3.6 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the power management control ECU is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 4.6 seconds. | Master warning light turns on. | DTC is stored until it is cleared using the GTS. |
| U0151 | Communication Error from Airbag ECU to HV ECU | The power management control ECU (HV CPU) does not receive data from the airbag sensor assembly for 10.6 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the power management control ECU is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 11.6 seconds. | Master warning light turns on. | DTC is stored until it is cleared using the GTS. |
| U0164 | Communication Error from A/C ECU to HV ECU | The power management control ECU (HV CPU) does not receive data from the air conditioning amplifier assembly for 10.6 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the power management control ECU is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 11.6 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U029A*2 | Lost Communication with Hybrid Battery Pack Sensor Module | The power management control ECU (HV CPU) does not receive data from the battery smart unit for 0.5 seconds or more. | The power switch is on (IG) for 0.5 seconds or more. | Turn the power switch on (IG) and wait at least 1 second. | Master warning light turns on. | DTC is stored until it is cleared using the GTS. |
| U0424*1 | Invalid Data Received from HVAC Control Module | The power management control ECU (HV CPU) receives an abnormal operation value command from the air conditioning amplifier assembly for 3 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 0.5 seconds or more. ·
The power source voltage of the power management control ECU is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 3.5 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U1104*3 | Lost Communication with Driving Support ECU | The power management control ECU (HV CPU) does not receive data from the driving support ECU assembly for 1.02 seconds or more. | All conditions are met:
·
The power switch is on (IG) for 2.1 seconds or more. ·
Vehicle speed is 36 km/h (22 mph) or more. ·
The power source voltage of the power management control ECU is 9.5 V or more. |
Drive the vehicle at a speed of 36 km/h (22 mph) or more for 3.12 seconds or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U1107 | Lost Communication with Power Management Module | The power management control ECU (HV CPU) does not receive data from the power management control ECU (power management CPU) for 3.6 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the power management control ECU is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 4.6 seconds. | Master warning light turns on. | DTC is stored until it is cleared using the GTS. |
Power Management Control ECU / GTS Display "Power Source Control"
This ECU uses the CAN communication system for DTC communication.
*: Refer to Smart Entry and Start System (for Start Function).
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0140 | Lost Communication with Main Body ECU | The power management control ECU (power management CPU) does not receive data from the main body ECU (multiplex network body ECU) for 3.1 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 10 seconds or more. ·
The power source voltage of the power management control ECU is 10 V or more. |
Turn the power switch on (IG) and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0155 | Lost Communication with Combination Meter | The power management control ECU (power management CPU) does not receive data from the combination meter assembly for 3.1 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 10 seconds or more. ·
The power source voltage of the power management control ECU is 10 V or more. |
Turn the power switch on (IG) and wait at least 20 seconds. | A message is displayed on the multi-information display for 15 seconds when the power switch is turned from on (IG) to off. | DTC is stored until it is cleared using the GTS. |
| U0293* | Lost Communication with HV ECU | The power management control ECU (power management CPU) does not receive data from the power management control ECU (HV CPU) for 3.1 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 10 seconds or more. ·
The power source voltage of the power management control ECU is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 13.1 seconds. | - | DTC is stored until it is cleared using the GTS. |
Power Management Control ECU / GTS Display "Cruise Control"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0122 | Lost Communication with Vehicle Dynamics Control Module | While the cruise control system is on (the system has been switched on using the ON/OFF button on the cruise control switch), the power management control ECU (HV CPU) does not receive data from the brake booster with master cylinder assembly (skid control ECU) for 2.73 seconds or more. | All conditions are met:
·
The power switch is on (IG) for 2.1 seconds or more. ·
Vehicle speed is 36 km/h (22 mph) or more. ·
The power source voltage of the power management control ECU is 9.5 V or more. |
After turning the power switch on (IG), turn the cruise control main switch on and drive the vehicle at 36 km/h (22 mph) or more for 4.83 seconds or more. | ·
Displays messages on the multi-information display. ·
Master warning light turns on. |
DTC is stored until it is cleared using the GTS. |
Power Management Control ECU / GTS Display "PM1 Gateway"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0104 | Lost Communication with Cruise Control Module | The power management control ECU does not receive data from the driving support ECU assembly for 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 10 seconds or more. ·
The power source voltage of the power management control ECU is 10.5 V or more. |
Turn the power switch on (IG) and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0233 | Lost Communication with Blind Spot Monitor Master Module | The power management control ECU does not receive data from the blind spot monitor sensor RH for 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 10 seconds or more. ·
The power source voltage of the power management control ECU is 10.5 V or more. |
Turn the power switch on (IG) and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U023A | Lost Communication with Front Camera Module | The power management control ECU does not receive data from the lane departure warning camera for 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 10 seconds or more. ·
The power source voltage of the power management control ECU is 10.5 V or more. |
Turn the power switch on (IG) and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0265 | Lost Communication with Parking Assist Monitor Module | The power management control ECU does not receive data from the rear television camera assembly for 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 10 seconds or more. ·
The power source voltage of the power management control ECU is 10.5 V or more. |
Turn the power switch on (IG) and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U1002 | Lost Communication with Gateway Module | The power management control ECU detects communication errors between itself and the blind spot monitor sensor RH, driving support ECU assembly, lane departure warning camera and rear television camera assembly. | Both conditions are met:
·
The power switch is on (IG) for 10 seconds or more. ·
The power source voltage of the power management control ECU is 10.5 V or more. |
Turn the power switch on (IG) and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
ECM / GTS Display "Engine and ECT"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0293 | Lost Communication with HV ECU | The ECM does not receive data from the power management control ECU (HV CPU) for 0.576 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the ECM is 10.5 V or more. |
Turn the power switch on (IG) and wait at least 5 seconds. | MIL illuminates. | DTC is stored until it is cleared using the GTS. |
Power Steering ECU Assembly / GTS Display "EMPS"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0129 | Lost Communication with Brake System Control Module | The power steering ECU assembly does not receive data from the brake booster with master cylinder assembly (skid control ECU) for 2.3 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 2 seconds or more. ·
The power source voltage of the power steering ECU assembly is 9 V or more. |
Turn the power switch on (IG) and wait at least 4.3 seconds. | EPS warning light illuminates. | DTC remains stored only while malfunction is occurring. |
| U0293 | Lost Communication with Hybrid Control Module | The power steering ECU assembly does not receive data from the power management control ECU (HV CPU) for 5 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 2 seconds or more. ·
The power source voltage of the power steering ECU assembly is 9 V or more. |
Turn the power switch on (IG) and wait at least 7 seconds. | EPS warning light illuminates. | DTC remains stored only while malfunction is occurring. |
Brake Booster with Master Cylinder Assembly (Skid Control ECU) / GTS Display "ABS/VSC/TRC"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0073 | Control Module Communication Bus OFF | One of the following conditions is met:
1.
The brake booster with master cylinder assembly (skid control ECU) keeps sending data to an ECU or sensor for 5 seconds or more because a reception completion is not received. 2.
The yaw rate sensor, acceleration sensor or steering sensor and brake booster with master cylinder assembly (skid control ECU) does not communicate for 1 second or more. 3.
The following condition occurs 10 times in succession within 60 seconds: ·
The yaw rate sensor, acceleration sensor or steering sensor does not communicate with the brake booster with master cylinder assembly (skid control ECU) once or more within 5 seconds. 4.
The following condition occurs 10 times in succession: ·
The brake booster with master cylinder assembly (skid control ECU) does not send/ receive data (bus off) once or more within 0.1 seconds. |
Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the brake booster with master cylinder assembly (skid control ECU) is 10 to 17.4 V or more. |
Turn the power switch on (IG) and wait at least 60 seconds. | <When data can be sent to the combination meter>
·
ABS warning light illuminates. ·
Brake warning light / yellow (minor malfunction) illuminates. ·
Slip indicator light illuminates. |
DTC is stored until it is cleared using the GTS. |
| <When data cannot be sent to the combination meter>
·
ABS warning light illuminates. ·
Brake warning light / red (malfunction) illuminates. ·
Slip indicator light illuminates. |
||||||
| U0123 | Lost Communication with Yaw Rate Sensor Module | Either of the following conditions is met:
1.
The brake booster with master cylinder assembly (skid control ECU) does not receive data from the yaw rate sensor for 1 second or more. 2.
The following condition occurs 10 times in succession within 60 seconds: ·
The brake booster with master cylinder assembly (skid control ECU) does not communicate with the yaw rate sensor once or more within 5 seconds. |
Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the brake booster with master cylinder assembly (skid control ECU) is 10 to 17.4 V or more. |
Turn the power switch on (IG) and wait at least 60 seconds. | ·
ABS warning light illuminates. ·
Brake warning light / yellow (minor malfunction) illuminates. ·
Slip indicator light illuminates. |
DTC is stored until it is cleared using the GTS. |
| U0124 | Lost Communication with Lateral Acceleration Sensor Module | Either of the following conditions is met:
1.
The brake booster with master cylinder assembly (skid control ECU) does not receive data from the acceleration sensor for 1 second or more. 2.
The following condition occurs 10 times in succession within 60 seconds: ·
The brake booster with master cylinder assembly (skid control ECU) does not communicate with the acceleration sensor once or more within 5 seconds. |
Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the brake booster with master cylinder assembly (skid control ECU) is 10 to 17.4 V or more. |
Turn the power switch on (IG) and wait at least 60 seconds. | ·
ABS warning light illuminates. ·
Brake warning light / yellow (minor malfunction) illuminates. ·
Slip indicator light illuminates. |
DTC is stored until it is cleared using the GTS. |
| U0126 | Lost Communication with Steering Angle Sensor Module | Either of the following conditions is met:
1.
The brake booster with master cylinder assembly (skid control ECU) does not receive data from the steering sensor for 1 second or more. 2.
The following condition occurs 10 times in succession within 60 seconds: ·
The brake booster with master cylinder assembly (skid control ECU) does not communicate with the steering sensor once or more within 5 seconds. |
Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the brake booster with master cylinder assembly (skid control ECU) is 10 to 17.4 V or more. |
Turn the power switch on (IG) and wait at least 60 seconds. | Slip indicator light illuminates. | DTC is stored until it is cleared using the GTS. |
| U0293 | Communication Error from HV ECU | Either of the following conditions is met:
1.
With the IG2 terminal voltage of the brake booster with master cylinder assembly (skid control ECU) 9.5 V or more, the brake booster with master cylinder assembly (skid control ECU) does not receive data from the power management control ECU (HV CPU) for 2 seconds or more. 2.
The following condition occurs 10 times in succession within 60 seconds: ·
With the IG2 terminal voltage of the brake booster with master cylinder assembly (skid control ECU) 9.5 V or more, the brake booster with master cylinder assembly (skid control ECU) does not receive data from the power management control ECU (HV CPU) once or more within 5 seconds. |
Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the brake booster with master cylinder assembly (skid control ECU) is 10 to 17.4 V or more. |
Turn the power switch on (IG) and wait at least 60 seconds. | ·
Brake warning light / yellow (minor malfunction) illuminates. ·
Slip indicator light illuminates. |
DTC is stored until it is cleared using the GTS. |
Steering Sensor / GTS Display "-"
The steering sensor is connected to the CAN communication system, but the steering sensor does not store or output CAN communication DTCs.
Airbag Sensor Assembly / GTS Display "SRS Airbag"
The airbag sensor assembly is connected to the CAN communication system, but the airbag sensor assembly does not store or output CAN communication DTCs.
Main Body ECU (Multiplex Network Body ECU) / GTS Display "Main Body"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication With ECM/PCM "A" | The main body ECU (multiplex network body ECU) does not receive data from the ECM for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the power switch on (IG) and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0101 | Lost Communication with TCM | The main body ECU (multiplex network body ECU) does not receive data from the power management control ECU (HV CPU) for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the power switch on (IG) and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0120 | Lost Communication With Starter / Generator Control Module | The main body ECU (multiplex network body ECU) does not receive data from the power management control ECU (power management CPU) for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the power switch on (IG) and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0151 | Lost Communication With Restraints Control Module | The main body ECU (multiplex network body ECU) does not receive data from the airbag sensor assembly for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the power switch on (IG) and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0155 | Lost Communication with Instrument Panel Cluster (IPC) Control Module | The main body ECU (multiplex network body ECU) does not receive data from the combination meter assembly for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the power switch on (IG) and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0164 | Lost Communication With HVAC Control Module | The main body ECU (multiplex network body ECU) does not receive data from the air conditioning amplifier assembly for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the power switch on (IG) and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0199 | Lost Communication with "Door Control Module A" | The main body ECU (multiplex network body ECU) does not receive data from the outer mirror control ECU assembly (for driver side) for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the power switch on (IG) and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0200 | Lost Communication with "Door Control Module B" | The main body ECU (multiplex network body ECU) does not receive data from the outer mirror control ECU assembly (for front passenger side) for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the power switch on (IG) and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0208 | Lost Communication with "Seat Control Module A" | The main body ECU (multiplex network body ECU) does not receive data from the position control ECU and switch assembly (for driver side) for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the power switch on (IG) and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U023A | Lost Communication with Front Camera Module | The main body ECU (multiplex network body ECU) does not receive data from the lane departure warning camera for 5 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the power switch on (IG) and wait at least 15 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0293 | Lost Communication With Hybrid Powertrain Control Module | The main body ECU (multiplex network body ECU) does not receive data from the power management control ECU (HV CPU) for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the power switch on (IG) and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0327 | Software Incompatibility with Vehicle Security Control Module | The main body ECU (multiplex network body ECU) does not receive data from the smart key ECU assembly (certification ECU) for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the power switch on (IG) and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U1002 | Lost Communication with Gateway Module | The main body ECU (multiplex network body ECU) detects communication errors between itself and the outer mirror control ECU assembly (for driver side), outer mirror control ECU assembly (for front passenger side) and position control ECU and switch assembly (for driver side). | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the power switch on (IG) and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
Smart Key ECU Assembly (Certification ECU) / GTS Display "Entry&Start"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication with ECM | The smart key ECU assembly (certification ECU) does not receive data from the ECM for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the smart key ECU assembly (certification ECU) is 10 V or more. |
Turn the power switch on (IG) and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0142 | Lost Communication with Main Body ECU | The smart key ECU assembly (certification ECU) does not receive data from the main body ECU (multiplex network body ECU) for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the smart key ECU assembly (certification ECU) is 10 V or more. |
Turn the power switch on (IG) and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0155 | Lost Communication with Combination Meter | The smart key ECU assembly (certification ECU) does not receive data from the combination meter assembly for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the smart key ECU assembly (certification ECU) is 10 V or more. |
Turn the power switch on (IG) and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0293 | Lost Communication with HV ECU | The smart key ECU assembly (certification ECU) does not receive data from the power management control ECU (HV CPU) for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the smart key ECU assembly (certification ECU) is 10 V or more. |
Turn the power switch on (IG) and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
Air Conditioning Amplifier Assembly / GTS Display "Air Conditioner"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0131 | Lost Communication with Electric Power Steering ECU | The air conditioning amplifier assembly does not receive data from the power steering ECU assembly for 5 seconds or more. | Both conditions are met:
·
The power switch is on (IG). ·
The power source voltage of the air conditioning amplifier assembly is 8.5 V or more. |
Turn the power switch on (IG) and wait at least 5 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0142 | Lost Communication with Main Body ECU | The air conditioning amplifier assembly does not receive data from the main body ECU (multiplex network body ECU) for 5 seconds or more. | Both conditions are met:
·
The power switch is on (IG). ·
The power source voltage of the air conditioning amplifier assembly is 8.5 V or more. |
Turn the power switch on (IG) and wait at least 5 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0155 | Lost Communication with Combination Meter | The air conditioning amplifier assembly does not receive data from the combination meter assembly for 5 seconds or more. | Both conditions are met:
·
The power switch is on (IG). ·
The power source voltage of the air conditioning amplifier assembly is 8.5 V or more. |
Turn the power switch on (IG) and wait at least 5 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0293 | Lost Communication with HV ECU | The air conditioning amplifier assembly does not receive data from the power management control ECU (HV CPU) for 5 seconds or more. | Both conditions are met:
·
The power switch is on (IG). ·
The power source voltage of the air conditioning amplifier assembly is 8.5 V or more. |
Turn the power switch on (IG) and wait at least 5 seconds. | - | DTC is stored until it is cleared using the GTS. |
Combination Meter Assembly / GTS Display "Combination Meter"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication with ECM / PCM "A" | The combination meter assembly does not receive data from the ECM or power management control ECU (HV CPU) for 2 seconds or more. | Both conditions are met:
·
The power switch is on (IG). ·
The power source voltage of the combination meter assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 2 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Skid Control ECU | The combination meter assembly does not receive data from the brake booster with master cylinder assembly (skid control ECU) for 3 seconds or more. | Both conditions are met:
·
The power switch is on (IG). ·
The power source voltage of the combination meter assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 3 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0131 | Lost Communication with Power Steering Control Module | The combination meter assembly does not receive data from the power steering ECU assembly for 3 seconds or more. | Both conditions are met:
·
The power switch is on (IG). ·
The power source voltage of the combination meter assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 3 seconds. | EPS warning light illuminates. | DTC is stored until it is cleared using the GTS. |
| U0142 | Lost Communication with Main Body ECU | The combination meter assembly does not receive data from the main body ECU (multiplex network body ECU) for 3 seconds or more. | Both conditions are met:
·
The power switch is on (IG). ·
The power source voltage of the combination meter assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 3 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0151 | Lost Communication with Airbag ECU | The combination meter assembly does not receive data from the airbag sensor assembly for 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG). ·
The power source voltage of the combination meter assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 10 seconds. | SRS warning light illuminates. | DTC is stored until it is cleared using the GTS. |
| U0163 | Lost Communication with Navigation Control Module | The combination meter assembly does not receive data from the navigation receiver assembly for 3 seconds or more. | Both conditions are met:
·
The power switch is on (IG). ·
The power source voltage of the combination meter assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 3 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U023A | Lost Communication with Front Camera Module | The combination meter assembly does not receive data from the lane departure warning camera for 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG). ·
The power source voltage of the combination meter assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 10 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U1104 | Lost Communication with Driving Support ECU | The combination meter assembly does not receive data from the driving support ECU assembly for 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG). ·
The power source voltage of the combination meter assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 10 seconds. | - | DTC is stored until it is cleared using the GTS. |
Navigation Receiver Assembly (for Navigation Receiver Type) / GTS Display "Navigation System"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0073 | Sending Malfunction (Navigation to APGS) | The navigation receiver assembly does not send/receive data for 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the navigation receiver assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 11 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0100 | Lost Communication with ECM / PCM "A" | The navigation receiver assembly does not receive data from the ECM for 4 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the navigation receiver assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 5 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Brake System Control Module | The navigation receiver assembly does not receive data from the brake booster with master cylinder assembly (skid control ECU) for 1 second or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the navigation receiver assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 2 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0140 | Lost Communication with Body Control Module | The navigation receiver assembly does not receive data from the main body ECU (multiplex network body ECU) for 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the navigation receiver assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 11 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0155 | Meter ECU Communication | The navigation receiver assembly does not receive data from the combination meter assembly for 30 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the navigation receiver assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 31 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0164 | Air Conditioner ECU Communication | The navigation receiver assembly does not receive data from the air conditioning amplifier assembly for 15 seconds or more. | Both conditions are met:
·
The power switch is on (IG). ·
The power source voltage of the navigation receiver assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 15 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0293 | Lost Communication with HV ECU | The navigation receiver assembly does not receive data from the power management control ECU (HV CPU) for 4 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the navigation receiver assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 5 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U1110 | Clearance Sonar ECU Communication | The navigation receiver assembly does not receive data from the clearance warning ECU assembly for 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the navigation receiver assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 11 seconds. | - | DTC is stored until it is cleared using the GTS. |
Radio and Display Receiver Assembly (for Radio and Display Type) / GTS Display "Navigation System"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0073 | Sending Malfunction (Navigation to APGS) | The radio and display receiver assembly does not send/receive data for 10 seconds or more. | Both conditions are met:
·
The power switch is on (ACC) for 1 second or more. ·
The power source voltage of the radio and display receiver assembly is 9.5 V or more. |
Turn the power switch on (ACC) and wait at least 11 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0100 | Lost Communication with ECM | The radio and display receiver assembly does not receive data from the ECM for 4 seconds or more. | All conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the radio and display receiver assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 5 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Brake System Control Module | The radio and display receiver assembly does not receive data from the brake booster with master cylinder assembly (skid control ECU) for 1 second or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the radio and display receiver assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 2 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0140 | Lost Communication with Body Control Module | The radio and display receiver assembly does not receive data from the main body ECU (multiplex network body ECU) for 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the radio and display receiver assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 11 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0155 | Meter ECU Communication | The radio and display receiver assembly does not receive data from the combination meter assembly for 30 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the radio and display receiver assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 31 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0164 | Air Conditioner ECU Communication | The radio and display receiver assembly does not receive data from the air conditioning amplifier assembly for 15 seconds or more. | Both conditions are met:
·
The power switch is on (IG). ·
The power source voltage of the radio and display receiver assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 15 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0293 | Lost Communication with HV ECU | The radio and display receiver assembly does not receive data from the power management control ECU (HV CPU) for 3 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the radio and display receiver assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 4 seconds. | - | DTC is stored until it is cleared using the GTS. |
Blind Spot Monitor Sensor RH (w/ Blind Spot Monitor System) / GTS Display "Blind Spot Monitor Master"
This ECU uses the CAN communication system for DTC communication.
*1: Refer to Blind Spot Monitor System.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>U0232
*2: Refer to Blind Spot Monitor System.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>U1331
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0126 | Lost Communication with Steering Angle Sensor Module | The blind spot monitor sensor RH does not receive data from the steering sensor for 10.68 seconds or more. | All conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
Blind spot monitor main switch is on. ·
The power source voltage of the blind spot monitor sensor RH is 10 V or more. |
Turn the power switch on (IG), turn the blind spot monitor system on and wait at least 11.68 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Brake System Control Module | The blind spot monitor sensor RH does not receive data from the brake booster with master cylinder assembly (skid control ECU) for 2.334 seconds or more. | All conditions are met:
·
The power switch is on (IG) for 2 seconds or more. ·
Blind spot monitor main switch is on. ·
The power source voltage of the blind spot monitor sensor RH is 10 V or more. |
Turn the power switch on (IG), turn the blind spot monitor system on and wait at least 4.334 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0142 | Lost Communication with Body Control Module "B" | The blind spot monitor sensor RH does not receive data from the main body ECU (multiplex network body ECU) for 10.6 seconds or more. | All conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
Blind spot monitor main switch is on. ·
The power source voltage of the blind spot monitor sensor RH is 10 V or more. |
Turn the power switch on (IG), turn the blind spot monitor system on and wait at least 11.6 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0232*1 | Lost Communication with Blind Spot Monitor Slave Module | The blind spot monitor sensor RH does not receive data from the blind spot monitor sensor LH for 10.6 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the blind spot monitor sensor RH is 10 V or more. |
Turn the power switch on (IG) and wait at least 11.6 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0293 | Lost Communication with HV ECU | The blind spot monitor sensor RH does not receive data from the power management control ECU (HV CPU) for 10.84 seconds or more. | All conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
Vehicle speed is 5 km/h (3 mph) or more. ·
Blind spot monitor main switch is on. ·
The power source voltage of the blind spot monitor sensor RH is 10 V or more. |
Turn the power switch on (IG), turn the blind spot monitor system on and drive the vehicle at a speed of 5 km/h (3 mph) or more for 11.84 seconds or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U1331*2 | Software Incompatibility with Body Control Module "B" | Destination information of the main body ECU (multiplex network body ECU) and blind spot monitor sensor do not match. | Both conditions are met:
·
The power switch is on (IG). ·
The blind spot monitor main switch is on. |
Destination information of the main body ECU (multiplex network body ECU) and blind spot monitor sensor do not match. | Displays messages on the multi-information display. | DTC remains stored only while malfunction is occurring. |
Position Control ECU and Switch Assembly (for Driver side) (w/ Seat Position Memory System) / GTS Display "Driver Seat"
The position control ECU and switch assembly (for driver side) is connected to the CAN communication system, but the position control ECU and switch assembly (for driver side) does not store or output CAN communication DTCs.
Outer Mirror Control ECU Assembly (for Driver Side) (w/ Seat Position Memory System) / GTS Display "Mirror R"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0142 | Lost Communication with Body Control Module ''B'' | The outer mirror control ECU assembly (for driver side) does not receive data from the main body ECU (multiplex network body ECU) for 10 seconds or more. | Both conditions are met:
·
10 seconds have elapsed after connection of the auxiliary battery. ·
The power source voltage of the combination meter assembly is 10 V or more. |
Turn the power switch on (IG) and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
Outer Mirror Control ECU Assembly (for Front Passenger Side) (w/ Seat Position Memory System) / GTS Display "Mirror L"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0142 | Lost Communication with Body Control Module ''B'' | The outer mirror control ECU assembly (for front passenger side) does not receive data from the main body ECU (multiplex network body ECU) for 10 seconds or more. | Both conditions are met:
·
10 seconds have elapsed after connection of the auxiliary battery. ·
The power source voltage of the combination meter assembly is 10 V or more. |
Turn the power switch on (IG) and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
Rear Television Camera Assembly (w/ Parking Assist Monitor System without Parallel Parking Assist Function) / GTS Display "IPA/Parking Assist Monitor"
This ECU uses the CAN communication system for DTC communication.
*: The rear television camera assembly stores this DTC if an internal error related to the CAN communication system is detected.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication with ECM / PCM "A" | The rear television camera assembly does not receive data from the power management control ECU (HV CPU) for 11 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 3 seconds or more. ·
The power source voltage of the rear television camera assembly is 5.5 V or more. |
Turn the power switch on (IG) and wait at least 14 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0126 | Lost Communication with Steering Angle Sensor Module | The rear television camera assembly does not receive data from the steering sensor for 11 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 3 seconds or more. ·
The power source voltage of the rear television camera assembly is 5.5 V or more. |
Turn the power switch on (IG) and wait at least 14 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Brake System Control Module | The rear television camera assembly does not receive data from the brake booster with master cylinder assembly (skid control ECU) for 11 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 3 seconds or more. ·
The power source voltage of the rear television camera assembly is 5.5 V or more. |
Turn the power switch on (IG) and wait at least 14 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0131 | Lost Communication with Power Steering Control Module | The rear television camera assembly does not receive data from the power steering ECU assembly for 11 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 3 seconds or more. ·
The power source voltage of the rear television camera assembly is 5.5 V or more. |
Turn the power switch on (IG) and wait at least 14 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0140 | Lost Communication with Body Control Module | The rear television camera assembly does not receive data from the main body ECU (multiplex network body ECU) with motor assembly for 11 seconds or more. | Both conditions are met:
·
The power switch is on (ACC) for 3 seconds or more. ·
The power source voltage of the rear television camera assembly is 5.5 V or more. |
Turn the power switch on (IG) and wait at least 14 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0163 | Lost Communication with Navigation Control Module | The rear television camera assembly does not receive data from the navigation receiver assembly with motor assembly for 11 seconds or more. | Both conditions are met:
·
The power switch is on (ACC) for 3 seconds or more. ·
The power source voltage of the rear television camera assembly is 5.5 V or more. |
Turn the power switch on (IG) and wait at least 14 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U1000* | CAN Communication Failure (Message Registry) | When the power switch is on (ACC), a CAN communication malfunction is detected. | The power switch is on (ACC). | Turn the power switch on (ACC). | - | DTC remains stored only while malfunction is occurring. |
| U1110 | Lost Communication with Intuitive Parking Assist Module | The rear television camera assembly does not receive data from the clearance warning ECU assembly for 11 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 3 seconds or more. ·
The power source voltage of the rear television camera assembly is 5.5 V or more. |
Turn the power switch on (IG) and wait at least 14 seconds. | - | DTC is stored until it is cleared using the GTS. |
Clearance Warning ECU Assembly / GTS Display "Clearance Sonar"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication with ECM / PCM "A" | The clearance warning ECU assembly does not receive data from the ECM for 5.75 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 2 seconds or more. ·
The power source voltage of the clearance warning ECU assembly is 10 V or more. |
Turn the power switch on (IG) and wait at least 7.75 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0101 | Lost Communication with TCM | The clearance warning ECU assembly does not receive data from the power management control ECU (HV CPU) for 8.07 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 2 seconds or more. ·
The power source voltage of the clearance warning ECU assembly is 10 V or more. |
Turn the power switch on (IG) and wait at least 10.07 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0142 | Lost Communication with Body Control Module "B" | The clearance warning ECU assembly does not receive data from the main body ECU (multiplex network body ECU) for 5.9 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 2 seconds or more. ·
The power source voltage of the clearance warning ECU assembly is 10 V or more. |
Turn the power switch on (IG) and wait at least 7.9 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0155 | Lost Communication with Instrument Panel Cluster Control Module (Combination Meter) | The clearance warning ECU assembly does not receive data from the combination meter assembly for 6.5 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 2 seconds or more. ·
The power source voltage of the clearance warning ECU assembly is 10 V or more. |
Turn the power switch on (IG) and wait at least 8.5 seconds. | - | DTC is stored until it is cleared using the GTS. |
Lane Departure Warning Camera (w/ Lane Departure Alert System) / GTS Display "Lane Departure Alert"
This ECU uses the CAN communication system for DTC communication.
*: Refer to Lane Departure Alert System.
Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>U1000
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0101 | Lost Communication with TCM | The lane departure warning camera does not receive data from the power management control ECU (HV CPU) for 5 seconds or more. | All conditions are met:
·
The power switch is on (IG) for 2 seconds or more. ·
Vehicle speed is 1 km/h (or 1 mph) or more. ·
The power source voltage of the lane departure warning camera is 10 V or more. |
Drive the vehicle at a speed of 1 km/h (or 1 mph) or more for 7 seconds or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0123 | Lost Communication with Yaw Rate Sensor Module | The lane departure warning camera does not receive data from the airbag sensor assembly for 5 seconds or more. | All conditions are met:
·
The power switch is on (IG) for 2 seconds or more. ·
Vehicle speed is 1 km/h (or 1 mph) or more. ·
The power source voltage of the lane departure warning camera is 10 V or more. |
Drive the vehicle at a speed of 1 km/h (or 1 mph) or more for 7 seconds or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Brake System Control Module | The lane departure warning camera does not receive data from the brake booster with master cylinder assembly (skid control ECU) for 5 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 2 seconds or more. ·
The power source voltage of the lane departure warning camera is 10 V or more. |
Turn the power switch on (IG) and wait at least 7 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0142 | Lost Communication with Body Control Module "B" | The lane departure warning camera does not receive data from the main body ECU (multiplex network body ECU) for 5 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 2 seconds or more. ·
The power source voltage of the lane departure warning camera is 10 V or more. |
Turn the power switch on (IG) and wait at least 7 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0155 | Lost Communication with Instrument Panel Cluster (IPC) Control Module | The lane departure warning camera does not receive data from the combination meter assembly for 50 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 2 seconds or more. ·
The power source voltage of the lane departure warning camera is 10 V or more. |
Turn the power switch on (IG) and wait at least 52 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0293 | Lost Communication with Hybrid Control Module | The lane departure warning camera does not receive data from the power management control ECU for 5 seconds or more. | All conditions are met:
·
The power switch is on (IG) for 2 seconds or more. ·
Vehicle speed is 1 km/h (or 1 mph) or more. ·
The power source voltage of the lane departure warning camera is 10 V or more. |
Drive the vehicle at a speed of 1 km/h (or 1 mph) or more for 7 seconds or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U1000* | CAN Communication Failure (Message Registry) | When the power switch is on (IG) , a CAN communication malfunction is detected. | The power switch is on (IG). | Turn the power switch on (IG). | Displays messages on the multi-information display. | DTC remains stored only while malfunction is occurring. |
Driving Support ECU Assembly (w/ Pre-crash Safety System) / GTS Display "Radar Cruise"
This ECU uses the CAN communication system for DTC communication.
*: Refer to Dynamic Radar Cruise Control System.
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>U0235
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0125 | Lost Communication with Yaw Rate Sensor Module | The driving support ECU assembly does not receive data from the airbag sensor assembly for 1 second or more. | All conditions are met:
·
The cruise control main switch is on. ·
Vehicle speed is 36 km/h (22 mph) or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. |
After turning the power switch on (IG), turn the cruise control main switch on and drive the vehicle at 36 km/h (22 mph) or more for 1 second or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0126 | Lost Communication with Steering Angle Sensor Module | The driving support ECU assembly does not receive data from the steering sensor for 4 seconds or more. | All conditions are met:
·
The cruise control main switch is on. ·
Vehicle speed is 36 km/h (22 mph) or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. |
After turning the power switch on (IG), turn the cruise control main switch on and drive the vehicle at 36 km/h (22 mph) or more for 4 seconds or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Brake System Control Module | The driving support ECU assembly does not receive data from the brake booster with master cylinder assembly (skid control ECU) for 5.24 seconds or more. | All conditions are met:
·
The cruise control main switch is on. ·
Vehicle speed is 36 km/h (22 mph) or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. |
After turning the power switch on (IG), turn the cruise control main switch on and drive the vehicle at 36 km/h (22 mph) or more for 5.24 seconds or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0235* | Lost Communication with Cruise Control Front Distance Range Sensor | The driving support ECU assembly does not receive data from the millimeter wave radar sensor assembly for 1 second or more. | All conditions are met:
·
The cruise control main switch is on. ·
Vehicle speed is 36 km/h (22 mph) or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. |
After turning the power switch on (IG), turn the cruise control main switch on and drive the vehicle at 36 km/h (22 mph) or more for 1 second or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0293 | Lost Communication with Hybrid Vehicle Control System | The driving support ECU assembly or brake booster with master cylinder assembly (skid control ECU) does not receive data from the power management control ECU (HV CPU) for 4 seconds or more. | All conditions are met:
·
The cruise control main switch is on. ·
Vehicle speed is 36 km/h (22 mph) or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. |
After turning the power switch on (IG), turn the cruise control main switch on and drive the vehicle at 36 km/h (22 mph) or more for 4 seconds or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U1104* | Lost Communication with Driving Support ECU | The power management control ECU (HV CPU), brake booster with master cylinder assembly (skid control ECU) or millimeter wave radar sensor assembly does not receive data from the driving support ECU assembly for 1 second or more. | Both conditions are met:
·
The cruise control main switch is on. ·
Vehicle speed is 36 km/h (22 mph) or more. |
Drive the vehicle at 36 km/h (22 mph) for 1 second or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
Driving Support ECU Assembly (w/ Pre-crash Safety System) / GTS Display "Pre-Crash 2"
This ECU uses the CAN communication system for DTC communication.
*: Refer to Pre-crash Safety System.
Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>U0235
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0125 | Lost Communication with Yaw Rate Sensor Module | The driving support ECU assembly does not receive data from the airbag sensor assembly for 0.772 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 3 seconds or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. |
Turn the power switch on (IG) and wait at least 3.772 seconds. | ·
Displays messages on the multi-information display. ·
PCS indicator light flashes. |
DTC is stored until it is cleared using the GTS. |
| U0126 | Lost Communication with Steering Angle Sensor Module | The driving support ECU assembly does not receive data from the steering sensor for 3.76 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. |
Turn the power switch on (IG) and wait at least 4.76 seconds. | ·
Displays messages on the multi-information display. ·
PCS indicator light flashes. |
DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Brake System Control Module | The driving support ECU assembly does not receive data from the brake booster with master cylinder assembly (skid control ECU) for 5.24 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 2 seconds or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. |
Turn the power switch on (IG) and wait at least 7.24 seconds. | ·
Displays messages on the multi-information display. ·
PCS indicator light flashes. |
DTC is stored until it is cleared using the GTS. |
| U0142 | Lost Communication with Body Control Module "B" | The driving support ECU assembly does not receive data from the main body ECU (multiplex network body ECU) for 14.2 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. |
Turn the power switch on (IG) and wait at least 15.2 seconds. | ·
Displays messages on the multi-information display. ·
PCS indicator light flashes. |
DTC is stored until it is cleared using the GTS. |
| U0235* | Lost Communication with Cruise Control Front Distance Range Sensor | The driving support ECU assembly does not receive data from the millimeter wave radar sensor assembly for 0.652 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. |
Turn the power switch on (IG) and wait at least 1.652 seconds. | ·
Displays messages on the multi-information display. ·
PCS indicator light flashes. |
DTC is stored until it is cleared using the GTS. |
| U0293 | Lost Communication with HV ECU | The driving support ECU assembly does not receive data from the power management control ECU (HV CPU) for 3.808 seconds or more. | All conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. ·
Vehicle speed is 5 km/h (3 mph) or more. |
After turning the power switch on (IG), drive the vehicle at 5 km/h (3 mph) or more for 4.808 seconds or more. | ·
Displays messages on the multi-information display. ·
PCS indicator light flashes. |
DTC is stored until it is cleared using the GTS. |
| U1002 | Lost Communication with Gateway Module | The driving support ECU assembly does not receive data from the millimeter wave radar sensor assembly for 0.652 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. |
Turn the power switch on (IG) and wait at least 1.652 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U1104* | Lost Communication with Driving Support ECU | The ECM, brake booster with master cylinder assembly (skid control ECU) or millimeter wave radar sensor assembly does not receive data from the driving support ECU assembly for 1.504 seconds or more. | The power switch is on (IG) for 2 seconds or more. | Turn the power switch on (IG) and wait at least 3.504 seconds. | ·
Displays messages on the multi-information display. ·
PCS indicator light flashes. |
DTC is stored until it is cleared using the GTS. |
Millimeter Wave Radar Sensor Assembly (w/ Pre-crash Safety System) / GTS Display "-"
The millimeter wave radar sensor assembly is connected to the CAN communication system, but the millimeter wave radar sensor assembly does not store or output CAN communication DTCs.
DTC COMBINATION TABLE (OPEN OR SHORT IN V BUS, PAST COMMUNICATION ERROR)
Regarding a past communication error of an ECU and sensor connected to the V bus (in this case, normal is displayed when performing the CAN bus check, but communication DTCs are output), the probable CAN bus line(s) that had a malfunction can be determined based on the following DTC combination table.
Based on the table below and DTCs output from ECUs connected via CAN communication, the probable part for which communication stop occurred can be determined.
Regarding an open in a CAN branch and a communication stop that is currently occurring, the malfunctioning part can be confirmed easily by performing the CAN bus check using the GTS because the ECU or sensor connected to the CAN branch does not respond (the ECU or sensor name will not be displayed on the screen).
If an open in a CAN main bus line, a short between the CAN bus lines (CANH and CANL) or a +B or ground short in the CAN bus occurs, DTCs of almost all ECUs (or sensors) on the CAN bus may be output, or a message indicating a communication error may be displayed on the GTS screen. In this case, check the resistance of the CAN bus (steps 7 to 9) first.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
If an open occurs in just one of the lines of a CAN branch, DTCs which are not related to malfunctioning parts may be output (DTCs may be displayed randomly), or a message indicating a communication error may be displayed.
X: DTC is likely to be output.
â–²: DTC is unlikely to be output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
â—‹: DTC is output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
X: DTC is likely to be output.
â–²: DTC is unlikely to be output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
â—‹: DTC is output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
| - | Trouble Mode (CAN Bus Line Short Circuit or Short to GND) | ||||
|---|---|---|---|---|---|
| V Bus | |||||
| Output ECU | Output DTC | CANH to CANL | CANH to GND | CANL to GND | |
| V Bus | Airbag Sensor Assembly | - | - | - | - |
| Air Conditioning Amplifier Assembly | U0131 | â—‹ | â—‹ | â—‹ | |
| U0142 | â—‹ | â—‹ | â—‹ | ||
| U0155 | â—‹ | â—‹ | â—‹ | ||
| U0293 | â—‹ | â—‹ | â—‹ | ||
| V Bus | Navigation Receiver Assembly*1 | U0100 | â—‹ | â—‹ | â—‹ |
| U0129 | â—‹ | â—‹ | â—‹ | ||
| U0140 | â—‹ | â—‹ | â—‹ | ||
| U0155 | â—‹ | â—‹ | â—‹ | ||
| U0164 | â—‹ | â—‹ | â—‹ | ||
| U0293 | â—‹ | â—‹ | â—‹ | ||
| U1110 | â—‹ | â—‹ | â—‹ | ||
| Radio and Display Receiver Assembly*1 | U0100 | â—‹ | â—‹ | â—‹ | |
| U0129 | â—‹ | â—‹ | â—‹ | ||
| U0140 | â—‹ | â—‹ | â—‹ | ||
| U0155 | â—‹ | â—‹ | â—‹ | ||
| U0164 | â—‹ | â—‹ | â—‹ | ||
| U0293 | â—‹ | â—‹ | â—‹ | ||
| Main Body ECU (Multiplex Network Body ECU)*2 | U0100 | â—‹ | â—‹ | â—‹ | |
| U0101 | â—‹ | â—‹ | â—‹ | ||
| U0120 | â—‹ | â—‹ | â—‹ | ||
| U0151 | â—‹ | â—‹ | â—‹ | ||
| U0155 | â—‹ | â—‹ | â—‹ | ||
| U0164 | â—‹ | â—‹ | â—‹ | ||
| U023A | â—‹ | â—‹ | â—‹ | ||
| U0293 | â—‹ | â—‹ | â—‹ | ||
| U0327 | â—‹ | â—‹ | â—‹ | ||
| Brake Booster with Master Cylinder Assembly (Skid Control ECU)*1 | U0123 | â—‹ | â—‹ | â—‹ | |
| U0124 | â—‹ | â—‹ | â—‹ | ||
| U0126 | â—‹ | â—‹ | â—‹ | ||
| U0293 | â—‹ | â—‹ | â—‹ | ||
| Power Steering ECU Assembly | U0129 | â—‹ | â—‹ | â—‹ | |
| U0293 | â—‹ | â—‹ | â—‹ | ||
| ECM | U0293 | - | - | - | |
| Smart Key ECU Assembly (Certification ECU) | U0100 | â—‹ | â—‹ | â—‹ | |
| U0142 | â—‹ | â—‹ | â—‹ | ||
| U0155 | â—‹ | â—‹ | â—‹ | ||
| U0293 | â—‹ | â—‹ | â—‹ | ||
| Combination Meter Assembly | U0100 | â—‹ | â—‹ | â—‹ | |
| U0129 | â—‹ | â—‹ | â—‹ | ||
| U0131 | â—‹ | â—‹ | â—‹ | ||
| U0142 | â—‹ | â—‹ | â—‹ | ||
| U0151 | â—‹ | â—‹ | â—‹ | ||
| U0163 | â—‹ | â—‹ | â—‹ | ||
| U023A | â—‹ | â—‹ | â—‹ | ||
| U1104 | â—‹ | â—‹ | â—‹ | ||
| Power Management Control ECU (HV CPU) | U0100 | â—‹ | â—‹ | â—‹ | |
| U0129 | â—‹ | â—‹ | â—‹ | ||
| U0140 | â—‹ | â—‹ | â—‹ | ||
| U0151 | â—‹ | â—‹ | â—‹ | ||
| U0164 | â—‹ | â—‹ | â—‹ | ||
| U1107 | â—‹ | â—‹ | â—‹ | ||
| Power Management Control ECU
(Power Management CPU) |
U0140 | â—‹ | â—‹ | â—‹ | |
| U0155 | â—‹ | â—‹ | â—‹ | ||
| U0293 | â—‹ | â—‹ | â—‹ | ||
| V Bus | Power Management Control ECU
(Cruise Control) |
U0122 | â—‹ | â—‹ | â—‹ |
| Power Management Control ECU
(Gateway Function)*2 |
- | - | - | - | |
| Steering Sensor | - | - | - | - | |
| Clearance Warning ECU Assembly | U0100 | â—‹ | â—‹ | â—‹ | |
| U0101 | â—‹ | â—‹ | â—‹ | ||
| U0142 | â—‹ | â—‹ | â—‹ | ||
| U0155 | â—‹ | â—‹ | â—‹ | ||
| Sub Bus 1 | Outer Mirror Control ECU Assembly (for Driver Side) | U0142 | - | - | - |
| Outer Mirror Control ECU Assembly (for Front Passenger Side) | U0142 | - | - | - | |
| Position Control ECU and Switch Assembly (for Driver Side) | - | - | - | - | |
| Main Body ECU (Multiplex Network Body ECU)*2 | U0199 | - | - | - | |
| U0200 | - | - | - | ||
| U0208 | - | - | - | ||
| U1002 | - | - | - | ||
| Sub Bus 11 | Blind Spot Monitor Sensor RH | U0126 | â—‹ | â—‹ | â—‹ |
| U0129 | â—‹ | â—‹ | â—‹ | ||
| U0142 | â—‹ | â—‹ | â—‹ | ||
| U0293 | - | - | - | ||
| Power Management Control ECU (HV CPU) | U1104 | - | - | - | |
| Power Management Control ECU
(Gateway Function)*2 |
U0104 | - | - | - | |
| U0233 | - | - | - | ||
| U023A | - | - | - | ||
| U0265 | - | - | - | ||
| U1002 | - | - | - | ||
| Rear Television Camera Assembly | U0100 | â—‹ | â—‹ | â—‹ | |
| U0126 | â—‹ | â—‹ | â—‹ | ||
| U0129 | â—‹ | â—‹ | â—‹ | ||
| U0131 | â—‹ | â—‹ | â—‹ | ||
| U0140 | â—‹ | â—‹ | â—‹ | ||
| U0163 | â—‹ | â—‹ | â—‹ | ||
| U1110 | â—‹ | â—‹ | â—‹ | ||
| Sub Bus 11 | Lane Departure Warning Camera | U0101 | â—‹ | â—‹ | â—‹ |
| U0123 | â—‹ | â—‹ | â—‹ | ||
| U0129 | â—‹ | â—‹ | â—‹ | ||
| U0142 | â—‹ | â—‹ | â—‹ | ||
| U0155 | â—‹ | â—‹ | â—‹ | ||
| U0293 | - | - | - | ||
| Driving Support ECU Assembly
(Dynamic Radar Cruise Control System) |
U0125 | â—‹ | â—‹ | â—‹ | |
| U0126 | â—‹ | â—‹ | â—‹ | ||
| U0129 | â—‹ | â—‹ | â—‹ | ||
| U0293 | - | - | - | ||
| Driving Support ECU Assembly
(Pre-crash Safety System) |
U0125 | â—‹ | â—‹ | â—‹ | |
| U0126 | â—‹ | â—‹ | â—‹ | ||
| U0129 | â—‹ | â—‹ | â—‹ | ||
| U0142 | â—‹ | â—‹ | â—‹ | ||
| U0293 | - | - | - | ||
â—‹: DTC is output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
DTC COMBINATION TABLE (OPEN OR SHORT IN SUB BUS 1, PAST COMMUNICATION ERROR)
Regarding a past communication error of an ECU and sensor connected to sub bus 1 (in this case, normal is displayed when performing the CAN bus check, but communication DTCs are output), determine the part that had a malfunction based on DTCs output from the main body ECU (multiplex network body ECU).
As gateway function equipped ECUs (sub bus monitor ECU) monitor signals from all ECUs that are connected to sub buses, gateway function equipped ECUs can detect ECUs with a communication stop more accurately.
DTCs output from ECUs other than the main body ECU (multiplex network body ECU) (gateway function equipped ECU) are shown only as a reference.
Regarding a communication stop that is currently occurring in sub bus 1, the malfunctioning part can be confirmed easily by performing the CAN bus check using the GTS.
If an open occurs in just one of the lines of a CAN branch, DTCs which are not related to malfunctioning parts may be output (DTCs may be displayed randomly), or a message indicating a communication error may be displayed.
X: DTC is likely to be output.
â–²: DTC is unlikely to be output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
â—‹: DTC is output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
X: DTC is likely to be output.
â–²: DTC is unlikely to be output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
â—‹: DTC is output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
| - | Trouble Mode (CAN Bus Line Short Circuit or Short to GND) | ||||
|---|---|---|---|---|---|
| Sub Bus 1 | |||||
| Output ECU | Output DTC | CANH to CANL | CANH to GND | CANL to GND | |
| V Bus | Airbag Sensor Assembly | - | - | - | - |
| Air Conditioning Amplifier Assembly | U0131 | - | - | - | |
| U0142 | - | - | - | ||
| U0155 | - | - | - | ||
| U0293 | - | - | - | ||
| Navigation Receiver Assembly*1 | U0100 | - | - | - | |
| U0129 | - | - | - | ||
| U0140 | - | - | - | ||
| U0155 | - | - | - | ||
| U0164 | - | - | - | ||
| U0293 | - | - | - | ||
| U1110 | - | - | - | ||
| Radio and Display Receiver Assembly*1 | U0100 | - | - | - | |
| U0129 | - | - | - | ||
| U0140 | - | - | - | ||
| U0155 | - | - | - | ||
| U0164 | - | - | - | ||
| U0293 | - | - | - | ||
| Main Body ECU (Multiplex Network Body ECU)*2 | U0100 | - | - | - | |
| U0101 | - | - | - | ||
| U0120 | - | - | - | ||
| U0151 | - | - | - | ||
| U0155 | - | - | - | ||
| U0164 | - | - | - | ||
| U023A | - | - | - | ||
| U0293 | - | - | - | ||
| U0327 | - | - | - | ||
| Brake Booster with Master Cylinder Assembly (Skid Control ECU)*1 | U0123 | - | - | - | |
| U0124 | - | - | - | ||
| U0126 | - | - | - | ||
| U0293 | - | - | - | ||
| Power Steering ECU Assembly | U0129 | - | - | - | |
| U0293 | - | - | - | ||
| ECM | U0293 | - | - | - | |
| Smart Key ECU Assembly (Certification ECU) | U0100 | - | - | - | |
| U0142 | - | - | - | ||
| U0155 | - | - | - | ||
| U0293 | - | - | - | ||
| V Bus | Combination Meter Assembly | U0100 | - | - | - |
| U0129 | - | - | - | ||
| U0131 | - | - | - | ||
| U0142 | - | - | - | ||
| U0151 | - | - | - | ||
| U0163 | - | - | - | ||
| U023A | â—‹ | â—‹ | â—‹ | ||
| U1104 | â—‹ | â—‹ | â—‹ | ||
| Power Management Control ECU (HV CPU) | U0100 | - | - | - | |
| U0129 | - | - | - | ||
| U0140 | - | - | - | ||
| U0151 | - | - | - | ||
| U0164 | - | - | - | ||
| U1107 | - | - | - | ||
| Power Management Control ECU
(Power Management CPU) |
U0140 | - | - | - | |
| U0155 | - | - | - | ||
| U0293 | - | - | - | ||
| Power Management Control ECU
(Cruise Control) |
U0122 | - | - | - | |
| Power Management Control ECU
(Gateway Function)*2 |
- | - | - | - | |
| Steering Sensor | - | - | - | - | |
| Clearance Warning ECU Assembly | U0100 | - | - | - | |
| U0101 | - | - | - | ||
| U0142 | - | - | - | ||
| U0155 | - | - | - | ||
| Sub Bus 1 | Outer Mirror Control ECU Assembly (for Driver Side) | U0142 | â—‹ | â—‹ | â—‹ |
| Outer Mirror Control ECU Assembly (for Front Passenger Side) | U0142 | â—‹ | â—‹ | â—‹ | |
| Position Control ECU and Switch Assembly (for Driver Side) | - | - | - | - | |
| Main Body ECU (Multiplex Network Body ECU)*2 | U0199 | â—‹ | â—‹ | â—‹ | |
| U0200 | â—‹ | â—‹ | â—‹ | ||
| U0208 | â—‹ | â—‹ | â—‹ | ||
| U1002 | â—‹ | â—‹ | â—‹ | ||
| Sub Bus 11 | Blind Spot Monitor Sensor RH | U0126 | - | - | - |
| U0129 | - | - | - | ||
| U0142 | - | - | - | ||
| U0293 | - | - | - | ||
| Sub Bus 11 | Power Management Control ECU (HV CPU) | U1104 | - | - | - |
| Power Management Control ECU
(Gateway Function)*2 |
U0104 | - | - | - | |
| U0233 | - | - | - | ||
| U023A | - | - | - | ||
| U0265 | - | - | - | ||
| U1002 | - | - | - | ||
| Rear Television Camera Assembly | U0100 | - | - | - | |
| U0126 | - | - | - | ||
| U0129 | - | - | - | ||
| U0131 | - | - | - | ||
| U0140 | - | - | - | ||
| U0163 | - | - | - | ||
| U1110 | - | - | - | ||
| Lane Departure Warning Camera | U0101 | - | - | - | |
| U0123 | - | - | - | ||
| U0129 | - | - | - | ||
| U0142 | - | - | - | ||
| U0155 | - | - | - | ||
| U0293 | - | - | - | ||
| Driving Support ECU Assembly
(Dynamic Radar Cruise Control System) |
U0125 | - | - | - | |
| U0126 | - | - | - | ||
| U0129 | - | - | - | ||
| U0293 | - | - | - | ||
| Driving Support ECU Assembly
(Pre-crash Safety System) |
U0125 | - | - | - | |
| U0126 | - | - | - | ||
| U0129 | - | - | - | ||
| U0142 | - | - | - | ||
| U0293 | - | - | - | ||
â—‹: DTC is output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
DTC COMBINATION TABLE (OPEN OR SHORT IN SUB BUS 11, PAST COMMUNICATION ERROR)
Regarding a past communication error of an ECU and sensor connected to sub bus 11 (in this case, normal is displayed when performing the CAN bus check, but communication DTCs are output), determine the part that had a malfunction based on DTCs output from the power management control ECU.
As gateway function equipped ECUs (sub bus monitor ECU) monitor signals from all ECUs that are connected to sub buses, gateway function equipped ECUs can detect ECUs with a communication stop more accurately.
DTCs output from ECUs other than the power management control ECU (gateway function equipped ECU) are shown only as a reference.
Regarding a communication stop that is currently occurring in sub bus 11, the malfunctioning part can be confirmed easily by performing the CAN bus check using the GTS.
If an open occurs in just one of the lines of a CAN branch, DTCs which are not related to malfunctioning parts may be output (DTCs may be displayed randomly), or a message indicating a communication error may be displayed.
X: DTC is likely to be output.
â–²: DTC is unlikely to be output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
â—‹: DTC is output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
X: DTC is likely to be output.
â–²: DTC is unlikely to be output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
â—‹: DTC is output.
X: DTC is likely to be output.
â–²: DTC is unlikely to be output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
| - | Trouble Mode (Open in Both CAN Main Lines) | ||||
|---|---|---|---|---|---|
| Sub Bus 11 | |||||
| Output ECU | Output DTC | CAN No. 2 Junction Connector to CAN No. 6 Junction Connector | CAN No. 2 Junction Connector to CAN No. 3 Junction Connector | CAN No. 4 Junction Connector | |
| V Bus | Airbag Sensor Assembly | - | - | - | - |
| Air Conditioning Amplifier Assembly | U0131 | - | - | - | |
| U0142 | - | - | - | ||
| U0155 | - | - | - | ||
| U0293 | - | - | - | ||
| Navigation Receiver Assembly*1 | U0100 | - | - | - | |
| U0129 | - | - | - | ||
| U0140 | - | - | - | ||
| U0155 | - | - | - | ||
| U0164 | - | - | - | ||
| U0293 | - | - | - | ||
| U1110 | - | - | - | ||
| Radio and Display Receiver Assembly*1 | U0100 | - | - | - | |
| U0129 | - | - | - | ||
| U0140 | - | - | - | ||
| U0155 | - | - | - | ||
| U0164 | - | - | - | ||
| U0293 | - | - | - | ||
| Main Body ECU (Multiplex Network Body ECU)*2 | U0100 | - | - | - | |
| U0101 | - | - | - | ||
| U0120 | - | - | - | ||
| U0151 | - | - | - | ||
| U0155 | - | - | - | ||
| U0164 | - | - | - | ||
| U023A | - | - | - | ||
| U0293 | - | - | - | ||
| U0327 | - | - | - | ||
| Brake Booster with Master Cylinder Assembly (Skid Control ECU)*1 | U0123 | - | - | - | |
| U0124 | - | - | - | ||
| U0126 | - | - | - | ||
| U0293 | - | - | - | ||
| Power Steering ECU Assembly | U0129 | - | - | - | |
| U0293 | - | - | - | ||
| ECM | U0293 | - | - | - | |
| Smart Key ECU Assembly (Certification ECU) | U0100 | - | - | - | |
| U0142 | - | - | - | ||
| U0155 | - | - | - | ||
| U0293 | - | - | - | ||
| Combination Meter Assembly | U0100 | - | - | - | |
| U0129 | - | - | - | ||
| U0131 | - | - | - | ||
| U0142 | - | - | - | ||
| U0151 | - | - | - | ||
| U0163 | - | - | - | ||
| U023A | - | - | - | ||
| U1104 | - | - | - | ||
| V Bus | Power Management Control ECU (HV CPU) | U0100 | - | - | - |
| U0129 | - | - | - | ||
| U0140 | - | - | - | ||
| U0151 | - | - | - | ||
| U0164 | - | - | - | ||
| U1107 | - | - | - | ||
| Power Management Control ECU
(Power Management CPU) |
U0140 | - | - | - | |
| U0155 | - | - | - | ||
| U0293 | - | - | - | ||
| Power Management Control ECU
(Cruise Control) |
U0122 | - | - | - | |
| Power Management Control ECU
(Gateway Function)*2 |
- | - | - | - | |
| Steering Sensor | - | - | - | - | |
| Clearance Warning ECU Assembly | U0100 | - | - | - | |
| U0101 | - | - | - | ||
| U0142 | - | - | - | ||
| U0155 | - | - | - | ||
| Sub Bus 1 | Outer Mirror Control ECU Assembly (for Driver Side) | U0142 | - | - | - |
| Outer Mirror Control ECU Assembly (for Front Passenger Side) | U0142 | - | - | - | |
| Position Control ECU and Switch Assembly (for Driver Side) | - | - | - | - | |
| Main Body ECU (Multiplex Network Body ECU)*2 | U0199 | - | - | - | |
| U0200 | - | - | - | ||
| U0208 | - | - | - | ||
| U1002 | - | - | - | ||
| Sub Bus 11 | Blind Spot Monitor Sensor RH | U0126 | â—‹ | - | - |
| U0129 | â—‹ | - | - | ||
| U0142 | â—‹ | - | - | ||
| U0293 | â—‹ | - | - | ||
| Power Management Control ECU (HV CPU) | U1104 | - | - | - | |
| Power Management Control ECU
(Gateway Function)*2 |
U0104 | - | - | - | |
| U0233 | â—‹ | - | - | ||
| U023A | - | - | - | ||
| U0265 | â—‹ | â—‹ | - | ||
| U1002 | - | - | - | ||
| Sub Bus 11 | Rear Television Camera Assembly | U0100 | â—‹ | â—‹ | - |
| U0126 | â—‹ | â—‹ | - | ||
| U0129 | â—‹ | â—‹ | - | ||
| U0131 | â—‹ | â—‹ | - | ||
| U0140 | â—‹ | â—‹ | - | ||
| U0163 | â—‹ | â—‹ | - | ||
| U1110 | â—‹ | â—‹ | - | ||
| Lane Departure Warning Camera | U0101 | - | - | - | |
| U0123 | - | - | - | ||
| U0129 | - | - | - | ||
| U0142 | - | - | - | ||
| U0155 | - | - | - | ||
| U0293 | - | - | - | ||
| Driving Support ECU Assembly
(Dynamic Radar Cruise Control System) |
U0125 | - | - | - | |
| U0126 | - | - | - | ||
| U0129 | - | - | - | ||
| U0293 | - | - | - | ||
| Driving Support ECU Assembly
(Pre-crash Safety System) |
U0125 | - | - | - | |
| U0126 | - | - | - | ||
| U0129 | - | - | - | ||
| U0142 | - | - | - | ||
| U0293 | - | - | - | ||
â—‹: DTC is output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
| - | Trouble Mode (CAN Bus Line Short Circuit or Short to GND) | ||||
|---|---|---|---|---|---|
| Sub Bus 11 | |||||
| Output ECU | Output DTC | CANH to CANL | CANH to GND | CANL to GND | |
| V Bus | Airbag Sensor Assembly | - | - | - | - |
| Air Conditioning Amplifier Assembly | U0131 | - | - | - | |
| U0142 | - | - | - | ||
| U0155 | - | - | - | ||
| U0293 | - | - | - | ||
| Navigation Receiver Assembly*1 | U0100 | - | - | - | |
| U0129 | - | - | - | ||
| U0140 | - | - | - | ||
| U0155 | - | - | - | ||
| U0164 | - | - | - | ||
| U0293 | - | - | - | ||
| U1110 | - | - | - | ||
| V Bus | Radio and Display Receiver Assembly*1 | U0100 | - | - | - |
| U0129 | - | - | - | ||
| U0140 | - | - | - | ||
| U0155 | - | - | - | ||
| U0164 | - | - | - | ||
| U0293 | - | - | - | ||
| Main Body ECU (Multiplex Network Body ECU)*2 | U0100 | - | - | - | |
| U0101 | - | - | - | ||
| U0120 | - | - | - | ||
| U0151 | - | - | - | ||
| U0155 | - | - | - | ||
| U0164 | - | - | - | ||
| U023A | â—‹ | â—‹ | â—‹ | ||
| U0293 | - | - | - | ||
| U0327 | - | - | - | ||
| Brake Booster with Master Cylinder Assembly (Skid Control ECU)*1 | U0123 | - | - | - | |
| U0124 | - | - | - | ||
| U0126 | - | - | - | ||
| U0293 | - | - | - | ||
| Power Steering ECU Assembly | U0129 | - | - | - | |
| U0293 | - | - | - | ||
| ECM | U0293 | - | - | - | |
| Smart Key ECU Assembly (Certification ECU) | U0100 | - | - | - | |
| U0142 | - | - | - | ||
| U0155 | - | - | - | ||
| U0293 | - | - | - | ||
| Combination Meter Assembly | U0100 | - | - | - | |
| U0129 | - | - | - | ||
| U0131 | - | - | - | ||
| U0142 | - | - | - | ||
| U0151 | - | - | - | ||
| U0163 | - | - | - | ||
| U023A | â—‹ | â—‹ | â—‹ | ||
| U1104 | â—‹ | â—‹ | â—‹ | ||
| Power Management Control ECU (HV CPU) | U0100 | - | - | - | |
| U0129 | - | - | - | ||
| U0140 | - | - | - | ||
| U0151 | - | - | - | ||
| U0164 | - | - | - | ||
| U1107 | - | - | - | ||
| Power Management Control ECU
(Power Management CPU) |
U0140 | - | - | - | |
| U0155 | - | - | - | ||
| U0293 | - | - | - | ||
| Power Management Control ECU
(Cruise Control) |
U0122 | - | - | - | |
| V Bus | Power Management Control ECU
(Gateway Function)*2 |
- | - | - | - |
| Steering Sensor | - | - | - | - | |
| Clearance Warning ECU Assembly | U0100 | - | - | - | |
| U0101 | - | - | - | ||
| U0142 | - | - | - | ||
| U0155 | - | - | - | ||
| Sub Bus 1 | Outer Mirror Control ECU Assembly (for Driver Side) | U0142 | - | - | - |
| Outer Mirror Control ECU Assembly (for Front Passenger Side) | U0142 | - | - | - | |
| Position Control ECU and Switch Assembly (for Driver Side) | - | - | - | - | |
| Main Body ECU (Multiplex Network Body ECU)*2 | U0199 | - | - | - | |
| U0200 | - | - | - | ||
| U0208 | - | - | - | ||
| U1002 | - | - | - | ||
| Sub Bus 11 | Blind Spot Monitor Sensor RH | U0126 | â—‹ | â—‹ | â—‹ |
| U0129 | â—‹ | â—‹ | â—‹ | ||
| U0142 | â—‹ | â—‹ | â—‹ | ||
| U0293 | â—‹ | â—‹ | â—‹ | ||
| Power Management Control ECU (HV CPU) | U1104 | â—‹ | â—‹ | â—‹ | |
| Power Management Control ECU (Gateway Function)*2 | U0104 | â—‹ | â—‹ | â—‹ | |
| U0233 | â—‹ | â—‹ | â—‹ | ||
| U023A | â—‹ | â—‹ | â—‹ | ||
| U0265 | â—‹ | â—‹ | â—‹ | ||
| U1002 | â—‹ | â—‹ | â—‹ | ||
| Rear Television Camera Assembly | U0100 | â—‹ | â—‹ | â—‹ | |
| U0126 | â—‹ | â—‹ | â—‹ | ||
| U0129 | â—‹ | â—‹ | â—‹ | ||
| U0131 | â—‹ | â—‹ | â—‹ | ||
| U0140 | â—‹ | â—‹ | â—‹ | ||
| U0163 | â—‹ | â—‹ | â—‹ | ||
| U1110 | â—‹ | â—‹ | â—‹ | ||
| Lane Departure Warning Camera | U0101 | â—‹ | â—‹ | â—‹ | |
| U0123 | â—‹ | â—‹ | â—‹ | ||
| U0129 | â—‹ | â—‹ | â—‹ | ||
| U0142 | â—‹ | â—‹ | â—‹ | ||
| U0155 | â—‹ | â—‹ | â—‹ | ||
| U0293 | â—‹ | â—‹ | â—‹ | ||
| Sub Bus 11 | Driving Support ECU Assembly
(Dynamic Radar Cruise Control System) |
U0125 | â—‹ | â—‹ | â—‹ |
| U0126 | â—‹ | â—‹ | â—‹ | ||
| U0129 | â—‹ | â—‹ | â—‹ | ||
| U0293 | â—‹ | â—‹ | â—‹ | ||
| Driving Support ECU Assembly
(Pre-crash Safety System) |
U0125 | â—‹ | â—‹ | â—‹ | |
| U0126 | â—‹ | â—‹ | â—‹ | ||
| U0129 | â—‹ | â—‹ | â—‹ | ||
| U0142 | â—‹ | â—‹ | â—‹ | ||
| U0293 | â—‹ | â—‹ | â—‹ | ||
â—‹: DTC is output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
CAN BUS WAVEFORMS
This waveform is measured between terminals CANH and GND, and terminals CANL and GND of the DLC3. (Use this as a reference for diagnosis of CAN communication lines.)
When malfunctions in multiple ECUs are suspected based on the CAN bus check and DTCs checked using the GTS, check the resistance of the CAN bus using an ohmmeter first. If no problems are found, check the following waveforms.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
If a waveform is not similar to one of the following 3 patterns (Group 1), then an open in a CAN main bus line, an open in a CAN branch line, or a short between a CAN line (CANH or CANL) and ground is suspected (Group 2).
Wiggle the connector and wire harness to check if the waveform changes.
CAN bus waveforms (Group 1)
Normal waveform
Open in both of the lines (CANH and CANL) of a CAN branch
Waveforms (waveforms shown using dotted lines) are not present from an ECU or sensor connected to a CAN branch with an open circuit in both lines. (Waveforms from other ECUs or sensors are normal.)
Because this waveform is similar to a normal waveform, instead of using the waveform, the malfunctioning part can be narrowed down by performing a CAN bus check.
Short between the CAN bus lines (CANH and CANL)
Waveforms disappear.
If the malfunction is in an ECU, disconnecting the ECU will change the waveform. If the waveform does not change, a malfunction in the wire harness is suspected.
CAN bus waveforms (reference) (Group 2)
The following CAN bus waveforms can be used only as reference. The actual measured waveform may differ significantly depending on the location of the open or short circuit.
Open in a CAN branch line (CANH)
An abnormal waveform is output from an ECU with an open in one of its CAN branch lines. Because this abnormal output interferes with the signals from other ECUs, the output of other ECUs will also appear abnormal.
Narrow down the malfunctioning part by checking DTCs or performing a CAN bus check, or by checking waveform changes when ECUs or sensors are disconnected. The waveform will change to one for an open in both sides of a CAN branch when the ECU or sensor with an open CAN branch line is disconnected.
Open in a CAN branch line (CANL)
An abnormal waveform is output from an ECU with an open in one of its CAN branch lines. Because this abnormal output interferes with the signals from other ECUs, the output of other ECUs will also appear abnormal.
Narrow down the malfunctioning part by checking DTCs or performing a CAN bus check, or by checking waveform changes when ECUs or sensors are disconnected. The waveform will change to one for an open in both sides of a CAN branch when the ECU or sensor with an open CAN branch line is disconnected.
Open in a CAN main bus line (CANH)
Waveforms of ECUs or sensors that are nearer to the DLC3 than the open part are almost normal.
Waveforms of ECUs or sensors that are on the opposite side of the DLC3 from the open part are abnormal.
An open in a CAN main bus line can be confirmed by measuring the resistance between the CANH and CANL terminals of any CAN branch.
Short between a CAN bus line (CANH) and ground
Narrow down the shorted part by checking for waveform changes when disconnecting connectors from the CAN junction connectors or when disconnecting ECUs or sensors.
A short to ground in the CANH line can be confirmed by measuring the resistance between CANH and ground using an ohmmeter.
Short between a CAN bus line (CANL) and ground
Narrow down the shorted part by checking for waveform changes when disconnecting connectors from the CAN junction connectors or when disconnecting ECUs or sensors.
A short to ground in the CANL line can be confirmed by measuring the resistance between CANL and ground using an ohmmeter.
DATA SENDING/RECEIVING TABLE
Data sending/receiving table
If Data List items related to sent/received data are not displayed properly, the part for which communication is interrupted can be determined using the table below.
| Data Content | Data Detected and Sent by | Data Received by
(Can be Checked in the Data List) |
Data Received by
(Cannot be Checked in the Data List) |
Relevant Data List Item
[Selected System] |
|---|---|---|---|---|
| Accelerator position | Power management control ECU (HV CPU) | - | ·
Airbag sensor assembly ·
Driving support ECU assembly |
·
Accel Pedal Pos #1 [Hybrid Control] ·
Accel Pedal Pos #2 [Hybrid Control] |
| Engine speed | ECM | ·
Power management control ECU (HV CPU) ·
Combination meter assembly |
·
Airbag sensor assembly ·
Air conditioning amplifier assembly ·
Navigation receiver assembly ·
Radio and display receiver assembly ·
Main body ECU (Multiplex network body ECU) |
·
Engine Speed [Engine and ECT] ·
Engine Revolution [Hybrid Control] ·
Engine Rpm [Combination Meter] |
| Engine coolant temperature | ECM | ·
Air conditioning amplifier assembly ·
Combination meter assembly |
- | ·
Coolant Temp [Engine and ECT] ·
Engine Coolant Temp [Air Conditioner] ·
Coolant Temperature [Combination Meter] |
| Vehicle speed | Brake booster with master cylinder assembly (Skid control ECU) | ·
Power management control ECU (HV CPU) ·
Combination meter assembly*3 ·
Navigation receiver assembly ·
Radio and display receiver assembly ·
Power steering ECU assembly ·
Blind spot monitor sensor RH ·
Rear television camera assembly ·
Driving support ECU assembly |
Airbag sensor assembly | ·
Vehicle Speed [ABS/VSC/TRC] ·
Vehicle Spd [Hybrid Control] ·
Vehicle Speed Meter [Combination Meter] ·
Vehicle Speed [Navigation System] ·
Meter Vehicle Velocity [EMPS] ·
Vehicle Speed [Blind Spot Monitor Master] ·
Wheel Speed Sensor (4 wheel) [Advanced Parking Guidance / Parking Assist Monitor] ·
Vhcl Spd-Brake ECU[Radar Cruise] |
| Combination meter assembly*3 | ·
Position control ECU and switch assembly (for Driver side) ·
Clearance warning ECU assembly |
·
Power management control ECU (HV CPU) ·
Power management control ECU (Power management CPU) ·
Air conditioning amplifier assembly ·
Main body ECU (Multiplex network body ECU) ·
Smart key ECU assembly (Certification ECU) |
·
Vehicle Speed Meter [Combination Meter] ·
Vehicle Speed [Driver Seat] ·
Vehicle Speed Info [Clearance Sonar] |
|
| Wheel speed | Brake booster with master cylinder assembly (Skid control ECU) | Driving support ECU assembly | ·
Power steering ECU assembly ·
Blind spot monitor sensor RH ·
Lane departure warning camera |
·
FR Wheel Speed [ABS/VSC/TRC] ·
FL Wheel Speed [ABS/VSC/TRC] ·
RR Wheel Speed [ABS/VSC/TRC] ·
RL Wheel Speed [ABS/VSC/TRC] ·
Rear Whl Spd LH Sensor [Radar Cruise] ·
Rear Whl Spd RH Sensor [Radar Cruise] ·
Front Whl Spd LH Sensor [Radar Cruise] ·
Front Whl Spd RH Sensor [Radar Cruise] |
| Shift position | Power management control ECU (HV CPU) | ·
Navigation receiver assembly ·
Radio and display receiver assembly ·
Position control ECU and switch assembly (for Driver side) ·
Blind spot monitor sensor RH ·
Clearance warning ECU assembly |
·
Power management control ECU (Power management CPU) ·
Airbag sensor assembly ·
Main body ECU (Multiplex network body ECU) ·
Combination meter assembly ·
Rear television camera assembly ·
Driving support ECU assembly ·
Lane departure warning camera |
·
Shift Sensor Shift Pos [Hybrid Control] ·
Shift Sensor SW - P [Hybrid Control] ·
Shift Sensor SW - R [Hybrid Control] ·
Shift Sensor SW - N [Hybrid Control] ·
Shift Sensor SW - D [Hybrid Control] ·
Shift Sensor SW - B [Hybrid Control] ·
Shift Sensor SW - FD [Hybrid Control] ·
Shift Sensor SW - RV [Hybrid Control] ·
Shift Sensor SW - MJ [Hybrid Control] ·
Reverse Signal [Navigation System] ·
Shift P sw (PMN) [Driver Seat] ·
Reverse (Only for AT/CVT) [Blind Spot Monitor Master] ·
Parking Signal [Clearance Sonar] ·
Reverse Signal [Clearance Sonar] |
| Ambient temperature | Air conditioning amplifier assembly | ·
Power management control ECU (HV CPU) ·
ECM ·
Combination meter assembly |
·
Main body ECU (Multiplex network body ECU) ·
Clearance warning ECU assembly ·
Driving support ECU assembly |
·
Ambient Temp Sensor [Air Conditioner] ·
Ambient Temperature [Hybrid Control] ·
Ambient Temp for A/C [Engine and ECT] ·
Ambient Temperature [Combination Meter] |
| Driver door courtesy | Main body ECU (Multiplex network body ECU) | - | ·
Power management control ECU (HV CPU) ·
Power management control ECU (Power management CPU) ·
Smart key ECU assembly (Certification ECU) ·
Combination meter assembly*2 |
FR Door Courtesy [Main Body] |
| Steering angle sensor | Steering sensor | ·
Brake booster with master cylinder assembly (Skid control ECU) ·
Power steering ECU assembly ·
Blind spot monitor sensor RH ·
Driving support ECU assembly |
·
Airbag sensor assembly ·
Navigation receiver assembly ·
Rear television camera assembly |
·
Steering Angle Sensor [ABS/VSC/TRC] ·
Steering Angle Velocity [EMPS] ·
Steering Angle [Blind Spot Monitor Master] ·
Steering Angle [Radar Cruise] |
| Yaw rate sensor | Airbag sensor assembly | ·
Brake booster with master cylinder assembly (Skid control ECU) ·
Driving support ECU assembly |
Lane departure warning camera | ·
Yaw Rate Sensor [ABS/VSC/TRC] ·
Yaw Rate Sensor2 [ABS/VSC/TRC] ·
Yaw Rate Sensor [Radar Cruise] |
| Deceleration sensor | Airbag sensor assembly | ·
Brake booster with master cylinder assembly (Skid control ECU) ·
Driving support ECU assembly |
Power management control ECU (HV CPU) | ·
Deceleration Sensor [ABS/VSC/TRC] ·
Deceleration Sensor2 [ABS/VSC/TRC] ·
Deceleration Sensor 1 [Radar Cruise] ·
Deceleration Sensor 2 [Radar Cruise] |
| Side turn signal | Combination meter assembly | ·
Blind spot monitor sensor RH ·
Lane departure warning camera |
- | ·
Turn Signal Switch (Right) [Combination Meter] ·
Turn Signal Switch (Left) [Combination Meter] ·
Turn Switch State [Blind Spot Monitor Master] ·
Turn Signal Switch (Right) [Lane Departure Alert] ·
Turn Signal Switch (Left) [Lane Departure Alert] |
| Power switch condition | Main body ECU (Multiplex network body ECU) | ·
Smart key ECU assembly (Certification ECU) ·
Position control ECU and switch assembly (for Driver side) |
·
Outer mirror control ECU assembly (for Driver side) ·
Outer mirror control ECU assembly (for Front passenger side) ·
Rear television camera assembly |
·
ACC SW [Main Body] ·
IG SW [Main Body] ·
Ignition Switch [Entry&Start] ·
Ignition Switch [Driver Seat] |
| Power management control ECU (HV CPU) power source voltage*1 | Power management control ECU (HV CPU) | - | - | +B [Hybrid Control] |
| Power management control ECU (Power Management CPU) power source state*1 | Power management control ECU (Power management CPU) | - | - | Power Supply Condition [Power Source Control] |
| ECM power source voltage*1 | ECM | - | - | Battery Voltage [Engine and ECT] |
| Brake pedal stroke sensor*1 | Brake booster with master cylinder assembly (Skid control ECU) | - | - | ·
Stroke Sensor [ABS/VSC/TRC] ·
Stroke Sensor2 [ABS/VSC/TRC] |
| Power steering ECU assembly power source voltage*1 | Power steering ECU assembly | - | - | Battery Voltage [EMPS] |
| Intensity of light received by the solar sensor*1 | Air conditioning amplifier assembly | - | - | ·
Solar Sensor (D Side) [Air Conditioner] ·
Solar Sensor (P Side) [Air Conditioner] |
| Combination meter assembly power source voltage*1 | Combination meter assembly | - | - | +B Voltage Value [Combination Meter] |
| Radio and display receiver assembly power source voltage*1 | Radio and display receiver assembly | - | - | Battery Voltage [Navigation System] |
| Navigation receiver assembly power source voltage*1 | Navigation receiver assembly | - | - | Battery Voltage [Navigation System] |
| Driver door touch sensor*1 | Smart key ECU assembly (Certification ECU) | - | - | D-Door Touch Sensor [Entry&Start] |
| Position control ECU and switch assembly (for Driver side) power source voltage*1 | Position control ECU and switch assembly (for Driver side) | - | - | Power Voltage [Driver Seat] |
| Outer mirror control ECU assembly (for Driver side) power source voltage*1 | Outer mirror control ECU assembly (for Driver side) | - | - | +B Voltage Input Value [Mirror R] |
| Outer mirror control ECU assembly (for Front passenger side) power source voltage*1 | Outer mirror control ECU assembly (for Front passenger side) | - | - | +B Voltage Input Value [Mirror L] |
| Blind spot monitor sensor RH power supply voltage*1 | Blind spot monitor sensor RH | - | - | Power Supply Voltage [Blind Spot Monitor Master] |
| Clearance sonar main switch*1 | Clearance warning ECU assembly | - | - | Main Switch [Clearance Sonar] |
| Wiper operation status*1 | Driving support ECU assembly | - | - | ·
Wiper (Hi) [Radar Cruise] ·
Wiper (Lo) [Radar Cruise] ·
Wiper Information [Pre-Crash 2] |
*1: Whether the ECU that sends data is functioning or not can be judged by using the GTS to check items such as switches or sensors that send signals to the ECU via direct lines.
*2: Although the received contents cannot be checked in the Data List, whether or not the data is received normally can be checked by observing the combination meter.
*3: The combination meter assembly receives a vehicle speed signal from the brake booster with master cylinder assembly (skid control ECU) and sends the signal to other ECUs.
Details of relevant Data List items (Selected system: Hybrid Control)
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Hybrid Control / Data List.
Check the results by referring to the following table.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Engine Revolution | Engine speed | Min.: 0 rpm, Max.: 16383 rpm | While idling after the engine is warmed up and inspection mode:
Approximately 900 rpm While driving at a constant speed: No significant fluctuation |
- |
| Vehicle Spd | Vehicle speed | Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Vehicle stopped:
0 km/h (0 mph) While driving at a constant speed: No significant fluctuation |
- |
| +B | Auxiliary battery voltage | Min.: 0.00 V, Max.: 65.53 V | Constant:
10.00 to 15.00 V |
Auxiliary battery condition |
| Accel Pedal Pos #1 | Accelerator pedal position sensor No.1 | Min.: 0.0%, Max.: 100.0% | Accelerator pedal depressed:
Changes with accelerator pedal pressure |
Accelerator pedal sensor assembly |
| Accel Pedal Pos #2 | Accelerator pedal position sensor No.2 | Min.: 0.0%, Max.: 100.0% | Accelerator pedal depressed:
Changes with accelerator pedal pressure |
Accelerator pedal sensor assembly |
| Ambient Temperature | Ambient air temperature | Min.: -40°C (-40°F), Max.: 215°C (419°F) | Power switch on (IG):
Same as ambient air temperature |
Ambient temperature sensor |
| Shift Sensor Shift Pos | Shift position | P/R/N/D/B | Matches currently selected shift position:
P, R, N, D or B |
Shift lever position sensor |
| Shift Sensor SW - P | Shift lever position sensor | ON or OFF | Shift lever in P: ON
Shift lever in any position other than P: OFF |
Shift lever position sensor |
| Shift Sensor SW - R | Shift lever position sensor | ON or OFF | Shift lever in R: ON
Shift lever in any position other than R: OFF |
Shift lever position sensor |
| Shift Sensor SW - N | Shift lever position sensor | ON or OFF | Shift lever in N: ON
Shift lever in any position other than N: OFF |
Shift lever position sensor |
| Shift Sensor SW - D | Shift lever position sensor | ON or OFF | Shift lever in D: ON
Shift lever in any position other than D: OFF |
Shift lever position sensor |
| Shift Sensor SW - B | Shift lever position sensor | ON or OFF | Shift lever in B: ON
Shift lever in any position other than B: OFF |
Shift lever position sensor |
| Shift Sensor SW - FD | Shift lever position sensor | ON or OFF | Shift lever in D or B: ON
Shift lever in any position other than D or B: OFF |
Shift lever position sensor |
| Shift Sensor SW - RV | Shift lever position sensor | ON or OFF | Shift lever in R: ON
Shift lever in any position other than R: OFF |
Shift lever position sensor |
| Shift Sensor SW - MJ | Shift lever position sensor | ON or OFF | Shift lever in P, R, N, D or B: ON
Shift lever in any position other than P, R, N, D or B: OFF |
Shift lever position sensor |
Details of relevant Data List items (Selected system: Power Source Control)
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body / Power Source Control / Data List.
Check the results by referring to the following table.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Power Supply Condition | Power supply state | IG2 ON, ST ON, All OFF, IG1 ON or ACC ON | All OFF: Power switch off
ACC ON: Power switch on (ACC) IG1 ON: Power switch on (IG) (IG1 relay on) IG2 ON: Power switch on (IG) (IG2 relay on) ST ON: Sending hybrid control system start request signal |
Since the IG1 and IG2 relays turn on at approximately the same time, IG1 ON may not be displayed (the IG1 relay turns on for a very short time). |
Details of relevant Data List items (Selected system: Engine and ECT)
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Normal Condition: If no conditions are specifically stated for "idling", the shift lever should be in N or P, the A/C switch should be off and all accessory switches should be off.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in inspection mode (maintenance mode).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
Warm up the engine.
Turn the A/C switch off.
Turn the power switch off.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Engine Speed | Engine speed | Min.: 0 rpm, Max.: 16383 rpm | 900 to 1050 rpm: Idling | ·
Stored as Freeze Frame Data: Yes ·
When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed. |
| Coolant Temp | Coolant temperature | Min.: -40°C (-40°F), Max.: 140°C (284°F) | 75 to 100°C (167 to 212°F): After warming up | ·
Stored as Freeze Frame Data: Yes ·
This is the engine coolant temperature.
|
| Battery Voltage | Auxiliary battery voltage | Min.: 0 V, Max.: 65.535 V | 11 to 16 V: Power switch on (IG) | ·
Stored as Freeze Frame Data: Yes ·
If 11 V or less, characteristics of some electrical components may change. |
| Ambient Temp for A/C | Ambient temperature for A/C | Min.: -40°C (-40°F), Max.: 215°C (419°F) | - | Stored as Freeze Frame Data: Yes |
Details of relevant Data List items (Selected system: ABS/VSC/TRC)
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Warm up the engine.
Turn the power switch off.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stroke Sensor | Brake pedal stroke sensor assembly | Min.: 0.00 V, Max.: 5.00 V | Brake pedal released: 0.65 to 1.35 V | Reading increases when brake pedal is depressed |
| Stroke Sensor2 | Brake pedal stroke sensor assembly 2 | Min.: 0.00 V, Max.: 5.00 V | Brake pedal released: 3.65 to 4.35 V | Reading decreases when brake pedal is depressed |
| Deceleration Sensor | Acceleration sensor 1 | Min.: -18.525 m/s2, Max.: 18.387 m/s2 | - | During deceleration/acceleration: Changes continuously |
| Deceleration Sensor2 | Acceleration sensor 2 | Min.: -18.525 m/s2, Max.: 18.387 m/s2 | - | During deceleration/acceleration: Changes continuously |
| Yaw Rate Sensor | Yaw rate sensor 1 | Min.: -128°/s, Max.: 127°/s | Vehicle stationary: 0°/s
Turning right: -128 to 0°/s Turning left: 0 to 127°/s |
- |
| Yaw Rate Sensor2 | Yaw rate sensor 2 | Min.: -128°/s, Max.: 127°/s | Vehicle stationary: 0°/s
Turning right: -128 to 0°/s Turning left: 0 to 127°/s |
- |
| Steering Angle Sensor | Steering angle sensor | Min.: -3276.8°, Max.: 3276.7° | Turning left: Increases
Turning right: Decreases |
- |
| FR Wheel Speed | Front speed sensor RH | Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| FL Wheel Speed | Front speed sensor LH | Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| RR Wheel Speed | Rear speed sensor RH | Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| RL Wheel Speed | Rear speed sensor LH | Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Vehicle Speed | Maximum wheel speed sensor | Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
Details of relevant Data List items (Selected system: EMPS)
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Turn the power switch off.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Chassis / EMPS / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Meter Vehicle Velocity | Vehicle speed from meter | Min.: 0.0 km/h (0.0 mph)
Max.: 300.0 km/h (186.4 mph) |
·
Power switch on (READY) and vehicle stopped: 0 km/h (0 mph) ·
Power switch on (READY) and vehicle driven at a constant speed: No significant fluctuation |
- |
| Steering Angle Velocity | Steering angle speed | Min.: -32768 deg/s
Max.: 32767 deg/s |
Power switch on (READY) and steering wheel being turned: Value changes in proportion to steering speed
-The value increases when turning left and decreases when turning right |
- |
| Battery Voltage | Auxiliary battery voltage | Min.: 0.0 V
Max.: 25.5 V |
Power switch on (IG): 9 to 16 V | - |
Details of relevant Data List items (Selected system: Navigation System)
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Connect the GTS to the DLC3.
Turn the power switch on (READY).
Turn the GTS on.
Enter the following menus: Body / Navigation System / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Battery Voltage | Auxiliary battery voltage | Min.: 0 V, Max.:24 V | 11 to 15.5 V | - |
| Reverse Signal | Reverse signal | ON or OFF | ON: Shift lever in R
OFF: Shift lever not in R |
- |
| Vehicle Speed | Maximum wheel speed sensor reading | Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
Details of relevant Data List items (Selected system: Entry&Start)
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
When using the GTS with the power switch off to troubleshoot:
Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body / Entry&Start / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| D-Door Touch Sensor | Driver door touch sensor (unlock sensor) | ON or OFF | ON: Driver door touch sensor (unlock sensor) touched
OFF: Driver door touch sensor (unlock sensor) not touched |
·
Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily). ·
Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate. |
| Ignition Switch | Power switch on (IG) | ON or OFF | ON: Power switch on (IG)
OFF: Power switch off |
·
Displays whether the IG power source signal input is on or off. ·
Use this Data List item to help determine the cause when all smart entry and system/wireless functions do not operate. ·
If the electrical key transmitter sub-assembly is brought inside the vehicle and the power switch is pressed twice without depressing the brake pedal, the power switch will turn on (IG). At this time, the key ID code transmitted from the electrical key transmitter sub-assembly and the key ID code stored in the certification ECU (smart key ECU assembly) are compared, and the L code stored in the certification ECU (smart key ECU assembly) and the code stored in the steering lock ECU (steering lock actuator assembly) are compared, and if all codes match, the power source mode is considered on (IG) at that time. |
Details of relevant Data List items (Selected system: Combination Meter)
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Warm up the engine.
Turn the power switch off.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body / Combination Meter / Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Vehicle Speed Meter | Vehicle speed | Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Almost the same as actual vehicle speed | - |
| Engine Rpm | Engine speed | Min.: 0 rpm, Max.: 12750 rpm | Almost the same as actual engine speed | - |
| Coolant Temperature | Engine coolant temperature | Min.: 0°C (32°F), Max.: 127.5°C (261.5°F) | After warming up: 75 to 100°C (167 to 212°F) | - |
| +B Voltage Value | Auxiliary battery voltage | Min.: 0 V, Max.: 25.5 V | 11 to 14 V | - |
| Ambient Temperature | Outside temperature | Min.: -40°C (-40°F), Max.: 87.5°C (189.5°F) | Almost the same as actual outside temperature | The temperature displayed on the multi-information display is -40 to 50°C (-40 to 122°F) |
| Turn Signal Switch (Right) | RH turn signal switch | OFF or ON | OFF: RH turn signal switch off
ON: RH turn signal switch on |
- |
| Turn Signal Switch (Left) | LH turn signal switch | OFF or ON | OFF: LH turn signal switch off
ON: LH turn signal switch on |
- |
Details of relevant Data List items (Selected system: Air Conditioner)
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body / Air Conditioner / Data List.
Check the value(s) by referring to the table below.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Ambient Temp Sensor | Ambient temperature sensor (thermistor assembly) | Min.: -23.30°C (-9.94°F)
Max.: 65.95°C (150.71°F) |
Actual ambient temperature displayed | - |
| Solar Sensor (D Side) | Driver side automatic light control sensor (solar sensor) | Min.: 0
Max.: 255 |
Driver side automatic light control sensor (solar sensor) value increases as brightness increases | - |
| Solar Sensor (P Side) | Front passenger side automatic light control sensor (solar sensor) | Min.: 0
Max.: 255 |
Front passenger side automatic light control sensor (solar sensor) value increases as brightness increases | - |
| Engine Coolant Temp | Engine coolant temperature sensor | Min.: 1.30°C (34.34°F)
Max.: 90.55°C (194.99°F) |
Actual engine coolant temperature displayed | - |
Details of relevant Data List items (Selected system: Main Body ECU)
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| ACC SW | Power switch status | ON or OFF | ON: Power switch on (ACC)
OFF: Power switch off |
- |
| IG SW | Power switch status | ON or OFF | ON: Power switch on (IG)
OFF: Power switch off |
- |
| FR Door Courtesy | Front RH door courtesy light switch signal | OPEN or CLOSE | OPEN: Front RH door open
CLOSE: Front RH door closed |
- |
Details of relevant Data List items (Selected system: Blind Spot Monitor Master)
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body / Blind Spot Monitor Master / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Turn Switch State | Master side, slave side state of the turn SW | Left ON, Right ON or OFF | Left ON: Left turn switch on
Right ON: Right turn switch on OFF: Switch not operated |
- |
| Reverse (Only for AT/CVT) | State of the shift position R signal | OFF or ON | ON: Shift lever in R
OFF: Shift lever in any position except R |
- |
| Vehicle Speed | Vehicle speed signal | Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph) | Vehicle stopped: 0 km/h (0 mph) | - |
| Steering Angle | Steering angle sensor | Min.: -3072°, Max.: 3070.5° | Left turn: Increases
Right turn: Decreases |
- |
| Power Supply Voltage | Power supply voltage | Min.: 0 V, Max.: 50 V | Always: 11 to 14 V | - |
Details of relevant Data List items (Selected system: Driver Seat)
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body / Driver Seat / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Ignition Switch | Communication state of power switch signal | ON or OFF | ON: Power switch on (IG) signal received
OFF: Power switch off signal not received |
- |
| Vehicle Speed | Vehicle speed data | min.: 0 km/h (0 mph), max.: 255 km/h (158 mph) | Actual vehicle speed | - |
| Power Voltage | Power supply for position control ECU and switch assembly | min: 0.95 V, max: 20.84 V | Within range from 11 V to 14 V | - |
| Shift P sw(PMN) | Park state signal | ON or OFF | ON: Shift lever in P
OFF: Shift lever in a position other than P |
- |
Details of relevant Data List items (Selected system: Mirror L)
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body / Mirror L / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| +B Voltage Input Value | Power supply for outer mirror control ECU assembly | MIN: 0 V, MAX: 19.98 V | Within range from 11 to 14 V | - |
Details of relevant Data List items (Selected system: Mirror R)
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body / Mirror R / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| +B Voltage Input Value | Power supply for outer mirror control ECU assembly | MIN: 0 V, MAX: 19.98 V | Within range from 11 to 14 V | - |
Details of relevant Data List items (Selected system: IPA/Parking Assist Monitor)
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Chassis / IPA/Parking Assist Monitor / Data List.
Read the Data List according to the display on the GTS.
Details of relevant Data List items (Selected system: Radar Cruise)
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body / Tilt & Telescopic / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Wiper (Hi) | Windshield wiper switch Hi signal | ON or OFF | ON: Windshield wiper switch Hi position
OFF: Windshield wiper switch except Hi position |
- |
| Wiper (Lo) | Windshield wiper switch Lo signal | ON or OFF | ON: Windshield wiper switch Lo position
OFF: Windshield wiper switch except Lo position |
- |
| Vhcl Spd-Brake ECU | Vehicle speed | min.: -327 km/h (-203 mph), max.: 327 km/h (204 mph) | Actual vehicle speed | - |
| Rear Whl Spd LH Sensor | Rear speed sensor LH signal | Normal or Abnoml | Normal: Rear speed sensor LH is normal
Abnoml: Rear speed sensor LH is abnormal |
- |
| Rear Whl Spd RH Sensor | Rear speed sensor RH signal | Normal or Abnoml | Normal: Rear speed sensor RH is normal
Normal: Rear speed sensor RH is normal |
- |
| Front Whl Spd LH Sensor | Front speed sensor LH signal | Normal or Abnoml | Normal: Front speed sensor LH is normal
Abnoml: Front speed sensor LH is abnormal |
- |
| Front Whl Spd RH Sensor | Front speed sensor RH signal | Normal or Abnoml | Normal: Front speed sensor RH is normal
Abnoml: Front speed sensor RH is abnormal |
- |
| Yaw Rate Sensor | Yaw rate value | min.: -100 deg/s, max.: 100 deg/s | Actual yaw rate value | - |
| Deceleration Sensor 1 | Deceleration value | min.: -14.7 m/s2, max.: 14.7 m/s2 | Actual deceleration value | - |
| Deceleration Sensor 2 | Deceleration value | min.: -14.7 m/s2, max.: 14.7 m/s2 | Actual deceleration value | - |
| Steering Angle | Steering angle | min.: -3072 deg, max.: 3070.5 deg | 0.0 deg is displayed when steering wheel is centered. | - |
Details of relevant Data List items (Selected system: Pre-Crash 2)
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Pre-Crash 2 / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Wiper Information | Wiper operational status | Unoperat, Oil off, Mist, Washer, Unknown, Intermi, Lo or Hi | The respective operational status displayed | - |
Details of relevant Data List items (Selected system: Clearance Sonar)
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body / Clearance Sonar / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Main Switch | Back sonar or clearance sonar switch assembly | OFF or ON | OFF: Back Sonar or Clearance Sonar Switch Assembly off
ON: Back Sonar or Clearance Sonar Switch Assembly on |
- |
| Parking Signal | Parking signal | OFF or ON | OFF: Shift lever in any position other than P
ON: Shift lever in P |
- |
| Reverse Signal | Reverse signal | OFF or ON | OFF: Shift lever not in R
ON: Shift lever in R |
- |
| Vehicle Speed Info | Vehicle speed signal | Snr Stop or Snr Work | Snr Stop: Vehicle speed approximately 13 km/h (8.1 mph) or more (when accelerating) or approximately 9 km/h (5.6 mph) or more (when decelerating)
Snr Work: Vehicle speed less than approximately 13 km/h (8.1 mph) (when accelerating) or less than approximately 9 km/h (5.6 mph) (when decelerating) |
- |
Details of relevant Data List items (Selected system: Lane Departure Alert)
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Chassis / Lane Departure Alert / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Turn Signal Switch (Right) | Status of turn signal light switch (right) | OFF or ON | ON: Turn signal light switch on (right)
OFF: Turn signal light switch off |
- |
| Turn Signal Switch (Left) | Status of turn signal light switch (left) | OFF or ON | ON: Turn signal light switch on (left)
OFF: Turn signal light switch off |
- |