Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2015.04
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074885 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0AFC-150  Hybrid Battery Pack Sensor Module  


DESCRIPTION

The power management control ECU alerts the driver and performs fail-safe control based on error signals sent from the battery smart unit.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0AFC-150 Hybrid Battery Pack Sensor Module Power source voltage of the battery smart unit drops during precharge.
·

Battery smart unit

·

Wire harness or connector


Comes on Master Warning Light:
Comes on

WIRING DIAGRAM

A260753E20
5.333,3.531 6.542,3.74 1.208,0.208 10 false Battery Smart Unit 2.292,0.917 2.719,1.135 0.427,0.219 10 false IGCT 4.573,0.438 5.521,0.635 0.948,0.198 10 false BATT VL SSR 0.625,2.729 1.656,2.927 1.031,0.198 10 false Auxiliary Battery 2.698,1.302 3.135,1.448 0.438,0.146 10 false MREL 2.698,2.333 3.135,2.479 0.438,0.146 10 false BTH+ 2.698,2.698 3.135,2.844 0.438,0.146 10 false BTH- 3.146,1.292 3.448,1.438 0.302,0.146 10 false A38 3.198,2.198 3.5,2.344 0.302,0.146 10 false 30 3.229,2.365 3.385,2.51 0.156,0.146 10 false I3 5.667,2.344 6.063,2.552 0.396,0.208 10 false BTH+ 5.667,2.667 6.083,2.885 0.417,0.219 10 false BTH- 5.469,2.25 5.656,2.417 0.188,0.167 10 false 1 5.667,0.271 6.104,0.448 0.438,0.177 10 false IGCT 2.771,0.198 2.99,0.365 0.219,0.167 10 false 5 2.042,0.198 2.24,0.354 0.198,0.156 10 false 3 2.042,0.563 2.25,0.708 0.208,0.146 10 false 2 2.76,0.552 2.958,0.729 0.198,0.177 10 false 1 4.719,0.156 4.844,0.313 0.125,0.156 10 false 1 5.115,0.156 5.26,0.333 0.146,0.177 10 false 2 5.667,3 6.073,3.198 0.406,0.198 10 false GND 5.469,2.906 5.677,3.073 0.208,0.167 10 false 6 0.49,0.833 1.271,1.052 0.781,0.219 10 false IGCT-MAIN 0.51,1.99 1.292,2.208 0.781,0.219 10 false MAIN 0.51,1.406 1.292,1.625 0.781,0.219 10 false R/B NO. 2 3.24,1.115 3.438,1.292 0.198,0.177 10 false 4 3.229,2.698 3.385,2.844 0.156,0.146 10 false I3 3.198,2.552 3.385,2.698 0.188,0.146 10 false 29 5.469,2.594 5.656,2.76 0.188,0.167 10 false 4 5.479,0.208 5.625,0.385 0.146,0.177 10 false 3 2.156,3.01 3.49,3.385 1.333,0.375 10 false Power Management Control ECU 5.333,3.344 5.615,3.521 0.281,0.177 10 false N18 2.823,1.646 3.146,1.844 0.323,0.198 10 false +B1 2.823,1.99 3.177,2.188 0.354,0.198 10 false +B2 3.24,1.5 3.438,1.677 0.198,0.177 10 false 3 3.24,1.833 3.438,2.01 0.198,0.177 10 false 1 3.146,1.667 3.448,1.813 0.302,0.146 10 false A39 3.135,2 3.438,2.146 0.302,0.146 10 false A38 4.344,1.104 5.198,1.333 0.854,0.229 10 false PM IGCT 4.104,0.896 4.229,1.052 0.125,0.156 10 false 1 4.104,1.26 4.25,1.438 0.146,0.177 10 false 2 0.271,1.031 0.396,1.188 0.125,0.156 10 false 1 0.271,0.677 0.417,0.854 0.146,0.177 10 false 2

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See pageEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:

After completing repairs, restart the system (turn the power switch on (READY)) and recheck for DTCs (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DTC CHECK / CLEAR).


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (IGCT VOLTAGE)

OK

NG

2.CHECK HARNESS AND CONNECTOR (GND - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (GND - BODY GROUND)

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATT VL SSR FUSE - BATTERY SMART UNIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND - BODY GROUND)