Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2015.04
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074885 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P3107-214  Lost Communication with Airbag System Control Module  


DESCRIPTION

Refer to the description for DTC P3107-213 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P3107-213).


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P3107-214 Lost Communication with Airbag System Control Module Open or short to +B in the communication circuit
·

Wire harness or connector

·

Airbag sensor assembly

·

Power management control ECU


Does not come on Master Warning Light:
Comes on

WIRING DIAGRAM

Refer to the wiring diagram for DTC P0AE6-225 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE6-225).

Refer to the wiring diagram for DTC P3107-213 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P3107-213).

PROCEDURE

1.CHECK DTC OUTPUT (SRS AIRBAG)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Body / SRS Airbag / DTC.

Body Electrical > SRS Airbag > Trouble Codes
50001 188

d.

Check if DTCs are output.

Result:
Result Proceed to
Airbag system DTCs are not output. A
Airbag system DTCs are output. B



e.

Turn the power switch off.



A

2.CHECK AIRBAG SENSOR ASSEMBLY (CHECK WAVEFORM)

B

2.CHECK AIRBAG SENSOR ASSEMBLY (CHECK WAVEFORM)

A

3.CLEAR DTC

B

6.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)
3.CLEAR DTC

NEXT

4.CHECK DTC OUTPUT (HYBRID CONTROL)
4.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.

Powertrain > Hybrid Control > Trouble Codes
50001 236

d.

Check if DTCs are output.

Result:
Result Proceed to
P3107-214 is not output. A
P3107-214 is output again. B



e.

Turn the power switch off.



A

5.CHECK FOR INTERMITTENT PROBLEMS

B

5.CHECK FOR INTERMITTENT PROBLEMS

OK

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

6.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

OK

7.CHECK CONNECTOR CONNECTION CONDITION (AIRBAG SENSOR ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

7.CHECK CONNECTOR CONNECTION CONDITION (AIRBAG SENSOR ASSEMBLY CONNECTOR)
a.
A256536C09
0.073,0.042 0.458,0.385 0.385,0.344 10 *a
*a Component with harness connected
(Airbag Sensor Assembly)


Check the connector connections and contact pressure of the relevant terminals for the airbag sensor assembly connectors.

OK:

The connectors are connected securely and there are no contact pressure problems.


Result:
Proceed to
OK
NG




OK

8.CHECK HARNESS AND CONNECTOR (+B SHORT)

NG

CONNECT SECURELY

8.CHECK HARNESS AND CONNECTOR (+B SHORT)
a.
A258634C09
1.51,0.677 0.625,0.885 false 0.135,0.125 0.385,0.333 0.25,0.208 10 *1 0.427,0.833 0.677,1.042 0.25,0.208 10 *2
*1 No. 2 Engine Room Relay Block
*2 PM IGCT Fuse


Remove the PM IGCT fuse from the No. 2 engine room relay block.


b.
A256541C06
2.365,1.104 2.75,0.969 false 0.24,0.198 0.469,0.406 0.229,0.208 10 *1 2.792,0.885 3.021,1.094 0.229,0.208 10 *2
*1 Engine Room Relay Block and Junction Block Assembly
*2 AM2 Fuse


Remove the AM2 fuse from the engine room relay block and junction block assembly.


c.
A265460C06
1.938,1.781 2.5,2.021 false 0.125,0.125 0.313,0.292 0.188,0.167 10 *1 2.51,1.969 2.698,2.135 0.188,0.167 10 *2
*1 Instrument Panel Junction Block Assembly
*2 ECU-IG2 NO. 1 Fuse


Remove the ECU-IG2 NO. 1 fuse from the instrument panel junction block assembly.


d.
A256537C09
0.583,1.625 1,1.865 0.417,0.24 0.083,0.052 0.344,0.229 0.26,0.177 10 false *a 0.667,1.667 1.219,1.969 0.552,0.302 10 false I47
*a Component without harness connected
(Airbag Sensor Assembly)


Disconnect connector I47 from the airbag sensor assembly.


e.
A258635C58
0.604,0.802 1.021,1.042 0.417,0.24 1.229,0.802 1.646,1.042 0.417,0.24 1.885,0.802 2.25,1.042 0.365,0.24 2.448,0.802 2.813,1.042 0.365,0.24 2.604,1.771 2.635,2.615 false 0.958,1.833 0.594,2.635 false 0.802,1.698 0.219,2.74 false 1.594,1.708 1.25,2.938 false 2.229,1.698 2.094,2.438 false 2.771,1.698 2.906,2.979 false 2.438,1.708 2.313,2.958 false 2.833,1.708 3.125,2.521 false 1.813,1.771 1.823,3 false 1,1.708 0.833,2.917 false 1.458,1.698 1.083,2.51 false 1.667,1.708 1.635,2.521 false 0.198,0.115 0.375,0.281 0.177,0.167 10 false *a 2.479,2.646 2.823,2.802 0.344,0.156 10 false ABFS 2.146,3 2.542,3.167 0.396,0.167 10 false AM21 1.906,2.469 2.292,2.635 0.385,0.167 10 false AM22 0.958,2.542 1.229,2.688 0.271,0.146 10 false +B1 0.708,2.958 0.979,3.104 0.271,0.146 10 false +B2 0.51,2.667 0.698,2.844 0.188,0.177 10 false GI 0.052,2.771 0.458,2.948 0.406,0.177 10 false MREL 1.521,2.563 1.792,2.74 0.271,0.177 10 false IG2 3,2.552 3.396,2.719 0.396,0.167 10 false ACCD 1.094,2.979 1.438,3.156 0.344,0.177 10 false IG2D 1.688,3.031 2.031,3.208 0.344,0.177 10 false SPDI 2.771,3.021 3.115,3.198 0.344,0.177 10 false IG1D 0.677,0.844 0.99,1.042 0.313,0.198 10 false A38 1.313,0.844 1.646,1.052 0.333,0.208 10 false A39 2.01,0.844 2.177,1.01 0.167,0.167 10 false I3 2.594,0.844 2.76,1.01 0.167,0.167 10 false I4
*a Component with harness connected
(Power Management Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
I4-13 (ABFS) - A38-1 (+B2) Power switch off 10 kΩ or higher
I4-13 (ABFS) - A39-3 (+B1) Power switch off 10 kΩ or higher
I4-13 (ABFS) - I3-1 (AM22) Power switch off 10 kΩ or higher
I4-13 (ABFS) - I4-7 (AM21) Power switch off 10 kΩ or higher
I4-13 (ABFS) - A38-4 (MREL) Power switch off 10 kΩ or higher
I4-13 (ABFS) - A39-1 (IG2) Power switch off 10 kΩ or higher
I4-13 (ABFS) - I4-1 (ACCD) Power switch off 10 kΩ or higher
I4-13 (ABFS) - I4-2 (IG1D) Power switch off 10 kΩ or higher
I4-13 (ABFS) - A39-2 (IG2D) Power switch off 10 kΩ or higher
I4-13 (ABFS) - I3-16 (SPDI) Power switch off 10 kΩ or higher
I4-13 (ABFS) - A38-19 (GI) Power switch off 10 kΩ or higher



f.

Connect the airbag sensor assembly connector.


g.

Install the PM IGCT fuse, AM2 fuse and ECU-IG2 NO. 1 fuse.

Result:
Proceed to
OK
NG




OK

9.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - AIRBAG SENSOR ASSEMBLY)

NG

11.CHECK HARNESS AND CONNECTOR (SHORT TO POWER SUPPLY WIRES)
9.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - AIRBAG SENSOR ASSEMBLY)
a.

Disconnect connector I4 from the power management control ECU.


b.

Disconnect connector I47 from the airbag sensor assembly.


c.

Measure the resistance according to the value(s) in the table below.

A335054C04
2.177,1.625 2.49,1.875 0.313,0.25 4.521,1.594 4.833,1.844 0.313,0.25 2.583,2.375 2.844,1.771 true 5.052,2.302 5.313,1.698 true 0.313,0.198 0.625,0.396 0.313,0.198 10 false *a 4.083,0.313 4.396,0.51 0.313,0.198 10 false *b 2.281,1.688 2.594,1.885 0.313,0.198 10 false I4 4.604,1.656 4.917,1.854 0.313,0.198 10 false I47 2.385,2.406 2.885,2.667 0.5,0.26 10 false ABFS 4.875,2.333 5.375,2.594 0.5,0.26 10 false GSW2
*a Rear view of wire harness connector
(to Power Management Control ECU)
*b Rear view of wire harness connector
(to Airbag Sensor Assembly)


Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
I4-13 (ABFS) - I47-14 (GSW2) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
I4-13 (ABFS) or I47-14 (GSW2) - Body ground and other terminals Power switch off 10 kΩ or higher


HINT:

As necessary, check that there is no short to power supply wires when performing the above wire harness inspection.



d.

Connect the airbag sensor assembly connector.


e.

Connect the power management control ECU connector.

Result:
Proceed to
OK
NG




OK

10.CHECK POWER MANAGEMENT CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK POWER MANAGEMENT CONTROL ECU
a.
A256537C10
0.583,1.625 1,1.865 0.417,0.24 0.083,0.052 0.344,0.229 0.26,0.177 10 false *a 0.667,1.667 1.219,1.969 0.552,0.302 10 false I47
*a Component without harness connected
(Airbag Sensor Assembly)


Disconnect connector I47 from the airbag sensor assembly.


b.

Turn the power switch on (IG).


c.
A258635C59
2.438,0.948 2.802,1.188 0.365,0.24 2.604,1.771 2.49,2.375 false 0.198,0.146 0.375,0.313 0.177,0.167 10 false *a 2.313,2.406 2.708,2.563 0.396,0.156 10 false ABFS 2.573,1.01 2.74,1.177 0.167,0.167 10 false I4
*a Component with harness connected
(Power Management Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I4-13 (ABFS) - Body ground Power switch on (IG) 11 to 14 V


NOTICE:

Turning the power switch on (IG) with the airbag sensor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



d.

Turn the power switch off.


e.

Connect the airbag sensor assembly connector.

Result:
Proceed to
OK
NG




OK

NG

11.CHECK HARNESS AND CONNECTOR (SHORT TO POWER SUPPLY WIRES)
a.
A258634C09
1.51,0.677 0.625,0.885 false 0.135,0.125 0.385,0.333 0.25,0.208 10 *1 0.427,0.833 0.677,1.042 0.25,0.208 10 *2
*1 No. 2 Engine Room Relay Block
*2 PM IGCT Fuse


Remove the PM IGCT fuse from the No. 2 engine room relay block.


b.
A256541C06
2.365,1.104 2.75,0.969 false 0.24,0.198 0.469,0.406 0.229,0.208 10 *1 2.792,0.885 3.021,1.094 0.229,0.208 10 *2
*1 Engine Room Relay Block and Junction Block Assembly
*2 AM2 Fuse


Remove the AM2 fuse from the engine room relay block and junction block assembly.


c.
A265460C06
1.938,1.781 2.5,2.021 false 0.125,0.125 0.313,0.292 0.188,0.167 10 *1 2.51,1.969 2.698,2.135 0.188,0.167 10 *2
*1 Instrument Panel Junction Block Assembly
*2 ECU-IG2 NO. 1 Fuse


Remove the ECU-IG2 NO. 1 fuse from the instrument panel junction block assembly.


d.
A256537C09
0.583,1.625 1,1.865 0.417,0.24 0.083,0.052 0.344,0.229 0.26,0.177 10 false *a 0.667,1.667 1.219,1.969 0.552,0.302 10 false I47
*a Component without harness connected
(Airbag Sensor Assembly)


Disconnect connector I47 from the airbag sensor assembly.


e.

Disconnect all the connectors from the power management control ECU.


f.
A317806C30
0.406,1.448 0.719,1.656 0.313,0.208 1.198,1.448 1.51,1.656 0.313,0.208 1.99,1.458 2.302,1.667 0.313,0.208 2.74,1.458 3.052,1.667 0.313,0.208 0.885,2.698 0.76,2.104 false 0.198,2.76 0.563,2.115 false 1.26,2.708 1.375,2.125 false 1.656,2.75 1.583,2.125 false 1.938,3.083 1.917,2.188 false 2.708,2.771 2.885,2.188 false 2.219,2.74 2.333,2.115 false 2.427,3.052 2.708,2.104 false 3.177,2.698 3.115,2.125 false 2.885,3.073 3.052,2.115 false 0.51,3.01 0.719,2.25 false 1.427,3.052 1.51,2.135 false 2.99,2.729 3.417,2.99 0.427,0.26 10 false ACCD 0.073,0.115 0.385,0.271 0.313,0.156 10 false *a 0.448,1.479 0.76,1.635 0.313,0.156 10 false A38 1.25,1.49 1.563,1.646 0.313,0.156 10 false A39 2.115,1.5 2.427,1.656 0.313,0.156 10 false I3 2.854,1.5 3.167,1.656 0.313,0.156 10 false I4 2.771,3.115 3.198,3.375 0.427,0.26 10 false IG1D 2.281,3.104 2.708,3.365 0.427,0.26 10 false AM21 2.031,2.771 2.458,3.031 0.427,0.26 10 false AM22 2.542,2.802 2.969,3.063 0.427,0.26 10 false ABFS 1.792,3.115 2.219,3.375 0.427,0.26 10 false SPDI 1.594,2.792 2.021,3.052 0.427,0.26 10 false IG2 1.135,2.74 1.563,3 0.427,0.26 10 false +B1 0.021,2.792 0.448,3.052 0.427,0.26 10 false MREL 0.781,2.74 1.208,3 0.427,0.26 10 false +B2 0.427,3.042 0.688,3.24 0.26,0.198 10 false GI 1.302,3.083 1.729,3.344 0.427,0.26 10 false IG2D
*a Rear view of wire harness connected
(Power Management Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
I4-13 (ABFS) - A38-1 (+B2) Power switch off 10 kΩ or higher
I4-13 (ABFS) - A39-3 (+B1) Power switch off 10 kΩ or higher
I4-13 (ABFS) - I3-1 (AM22) Power switch off 10 kΩ or higher
I4-13 (ABFS) - I4-7 (AM21) Power switch off 10 kΩ or higher
I4-13 (ABFS) - A38-4 (MREL) Power switch off 10 kΩ or higher
I4-13 (ABFS) - A39-1 (IG2) Power switch off 10 kΩ or higher
I4-13 (ABFS) - I4-1 (ACCD) Power switch off 10 kΩ or higher
I4-13 (ABFS) - I4-2 (IG1D) Power switch off 10 kΩ or higher
I4-13 (ABFS) - A39-2 (IG2D) Power switch off 10 kΩ or higher
I4-13 (ABFS) - I3-16 (SPDI) Power switch off 10 kΩ or higher
I4-13 (ABFS) - A38-19 (GI) Power switch off 10 kΩ or higher



g.

Connect the power management control ECU connectors.


h.

Connect the airbag ECU assembly connector.


i.

Install the PM IGCT fuse, AM2 fuse and ECU-IG2 NO. 1 fuse.

Result:
Proceed to
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR