Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2015.04
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074885 HYBRID CONTROL SYSTEM J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  Brake Override System  


DESCRIPTION

When the vehicle is being driven with the accelerator pedal depressed, depressing the brake pedal without releasing the accelerator pedal will activate the brake override system to restrict driving torque. The conditions for activating the brake override system as well as the items that are controlled are explained below.

A259906E05
2.667,2.917 3.594,3.115 0.927,0.198 10 false Vehicle Speed 0.74,2.031 2.042,2.51 1.302,0.479 10 false Brake Actuator (Skid Control ECU) 0.26,1.208 2.542,1.583 2.281,0.375 10 false Accelerator Pedal Sensor Assembly 3.271,3.344 5.438,3.635 2.167,0.292 10 false Power Management Control ECU 5.5,1.823 6.938,2.24 1.438,0.417 10 false Requested accelerator torque 2.594,0.979 3.771,1.354 1.177,0.375 10 false Actual Accelerator Pedal Angle 0.104,0.115 2.094,0.344 1.99,0.229 10 false Brake Override System: 2.635,1.969 3.74,2.333 1.104,0.365 10 false Braking torque

Activation Conditions:
·

The accelerator pedal and brake pedal are depressed at the same time.


NOTICE:

Brake override control may not be performed depending on the relationship between accelerator opening and vehicle speed.



Items Controlled:
·

Controls driving force


HINT:

When the control is operating, requested accelerator torque is controlled in accordance with the brake pedal stroke.



Deactivation Conditions:
·

The accelerator pedal or brake pedal is released.



CAUTION / NOTICE / HINT

Inspection Method

Drive at 10 km/h (6.25 mph), depress the accelerator pedal by 1/2 to 3/4 and keep it in that position. Under these conditions, if driving torque is controlled when the brake pedal is depressed by the left foot of the driver, it can be confirmed that the brake override system has operated.


CAUTION:

Perform this road test only in an appropriate safe location, in accordance with all local laws.

Pay careful attention to the surroundings when performing the road test.


HINT:
·

Under normal conditions, the Accelerator Degree value changes in response to the Accel Pedal Pos #1 value.

·

If the Data List values of Accelerator Degree and Accel Pedal Pos #1 do not match, and the value of Accel Pedal Pos #1 changes but the value of Accelerator Degree is constant, this confirms that the brake override system has operated. (Data can be captured relatively easily by using the snapshot function in Data List. Confirm the data after performing the road test.)

·

The brake override system restricts driving torque if the brake pedal is depressed when driving with the accelerator pedal depressed. If a customer reports experiencing a loss of power (driving torque) after the accelerator and brake pedals have both been intentionally depressed, explain that this is not a malfunction, and depressing both the accelerator and brake pedals at the same time should be avoided.



PROCEDURE

1.CHECK DTC OUTPUT (ALL CODES)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: System Select / Utility / All Codes.


d.

Check DTCs.

Result:
Result Proceed to
No DTCs are output A
DTCs are output B



e.

Turn the power switch off.



A

2.READ VALUE USING INTELLIGENT TESTER (MASTER CYLINDER CTRL TRQ)

B

GO TO DTC CHART

2.READ VALUE USING INTELLIGENT TESTER (MASTER CYLINDER CTRL TRQ)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Master Cylinder Ctrl Trq.


d.

Read the value displayed on the intelligent tester.

Powertrain > Hybrid Control > Data List
Tester Display Measurement Item Range Normal Condition
Master Cylinder Ctrl Trq Master cylinder control torque Min.: -4096 Nm, Max.: 4095 Nm Brake pedal depressed: Changes with the brake pedal pressure
Brake pedal released: 0 Nm
Powertrain > Hybrid Control > Data List
Tester Display
Master Cylinder Ctrl Trq
50003 236 105
Result:
Result Proceed to
Displayed value changes according to the brake pedal pressure. A
Displayed speed value does not change according to the brake pedal pressure. B



e.

Turn the power switch off.



A

3.READ VALUE USING INTELLIGENT TESTER (ACCEL PEDAL POS #1, ACCEL PEDAL POS #2)

B

CHECK BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

3.READ VALUE USING INTELLIGENT TESTER (ACCEL PEDAL POS #1, ACCEL PEDAL POS #2)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Accel Pedal Pos #1, Accel Pedal Pos #2.


d.

Read the value displayed on the intelligent tester.

Powertrain > Hybrid Control > Data List
Tester Display Measurement Item Range Normal Condition
Accel Pedal Pos #1 Accelerator pedal position sensor No. 1 Min.: 0%, Max.: 100% Accelerator pedal released → depressed → released: Changes with accelerator pedal pressure
Accel Pedal Pos #2 Accelerator pedal position sensor No. 2 Min.: 0%, Max.: 100% Accelerator pedal released → depressed → released: Changes with accelerator pedal pressure
Powertrain > Hybrid Control > Data List
Tester Display
Accel Pedal Pos #1
Accel Pedal Pos #2
50003 236 15,16
Result:
Result Proceed to
Displayed speed values smoothly changes following accelerator pedal operation. A
Displayed speed values does not smoothly change following accelerator pedal operation. B



e.

Turn the power switch off.



A

4.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPD)

B

4.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPD)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Vehicle Spd.


d.

Read the value displayed on the intelligent tester.

Powertrain > Hybrid Control > Data List
Tester Display Measurement Item Range Normal Condition
Vehicle Spd Vehicle speed Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) Vehicle stopped: 0 km/h (0 mph)
No large fluctuations when driving at a constant speed: Vehicle running at constant speed between 16 to 64 km/h (10 to 40 mph)
Powertrain > Hybrid Control > Data List
Tester Display
Vehicle Spd
50003 236 10
Result:
Result Proceed to
Displayed speed value does not fluctuate. A
Displayed speed value fluctuates. B


CAUTION:

Perform this road test only in an appropriate safe location, in accordance with all local laws.


HINT:

Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.



e.

Turn the power switch off.



A

5.READ VALUE USING INTELLIGENT TESTER (FR, FL, RR, RL WHEEL SPEED)

B

5.READ VALUE USING INTELLIGENT TESTER (FR, FL, RR, RL WHEEL SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (READY).


c.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List / All Data / FR Wheel Speed, FL Wheel Speed, RR Wheel Speed and RL Wheel Speed.


d.

Read the value displayed on the intelligent tester.

Chassis > ABS/VSC/TRC
Tester Display Measurement Item Range Normal Condition
FR Wheel Speed Front speed sensor RH Min.: 0.0 km/h (0 mph), Max.: 326.4 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph)
No large fluctuations when driving at a constant speed: Vehicle running at constant speed between 16 to 64 km/h (10 to 40 mph)
FL Wheel Speed Front speed sensor LH Min.: 0.0 km/h (0 mph), Max.: 326.4 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph)
No large fluctuations when driving at a constant speed: Vehicle running at constant speed between 16 to 64 km/h (10 to 40 mph)
RR Wheel Speed Rear speed sensor RH Min.: 0.0 km/h (0 mph), Max.: 326.4 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph)
No large fluctuations when driving at a constant speed: Vehicle running at constant speed between 16 to 64 km/h (10 to 40 mph)
RL Wheel Speed Rear speed sensor LH Min.: 0.0 km/h (0 mph), Max.: 326.4 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph)
No large fluctuations when driving at a constant speed: Vehicle running at constant speed between 16 to 64 km/h (10 to 40 mph)
Chassis > ABS/VSC/TRC > Data List
Tester Display
FR Wheel Speed
FL Wheel Speed
RR Wheel Speed
RL Wheel Speed
50003 105 1,2,3,4
Result:
Result Proceed to
Displayed speed value does not fluctuate. A
Displayed speed value fluctuates. B


CAUTION:

Perform this road test only in an appropriate safe location, in accordance with all local laws.


HINT:

Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.



e.

Turn the power switch off.



A

END

B

INSPECT FRONT OR REAR SPEED SENSOR