Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2015.04
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074885 HYBRID CONTROL SYSTEM J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  Pattern Select Switch Eco Mode Circuit  


DESCRIPTION

When selecting ECO mode, the ECO mode switch (eco switch assembly) operation signal is sent to the air conditioning amplifier assembly. Following this, ECO mode control is activated for the heater and air conditioning system.

WIRING DIAGRAM

A254642E06
0.941,1.233 2.162,1.542 1.221,0.309 10 Combination Meter assembly 2.973,1.233 4.24,1.542 1.267,0.309 10 Power Management Control ECU 4.574,3.946 6.8,4.102 2.226,0.156 10 Air Conditioning Amplifier Assembly 4.574,3.773 4.86,3.93 0.286,0.156 10 I77 1.147,3.526 3.833,3.687 2.686,0.161 10 ECO Mode Switch (Eco Switch Assembly) 0.6,4.412 2.198,4.556 1.598,0.144 10 : CAN Communication 1.147,3.353 1.539,3.509 0.392,0.156 10 I49 1.658,2.746 1.756,2.916 0.098,0.17 10 6 1.814,2.746 1.934,2.916 0.119,0.17 10 E 2.865,2.746 3.187,2.916 0.322,0.17 10 ECU 3.247,2.746 3.342,2.916 0.095,0.17 10 9 4.96,2.746 5.068,2.916 0.109,0.17 10 4 5.142,2.849 5.611,2.992 0.469,0.144 10 ECOS

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (CAN BUS CHECK)

A

2.CHECK DTC OUTPUT (ALL CODES)

B

2.CHECK DTC OUTPUT (ALL CODES)

A

3.READ VALUE USING INTELLIGENT TESTER (ECO MODE)

B

GO TO DTC CHART

3.READ VALUE USING INTELLIGENT TESTER (ECO MODE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / ECO Switch.


d.

Read the value displayed on the intelligent tester.

Powertrain > Hybrid Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ECO Mode ECO mode transition availability ON or OFF In ECO mode: ON -
Powertrain > Hybrid Control > Data List
Tester Display
ECO Mode
50003 236 521
Result:
Result Proceed to
The intelligent tester display changes according to the ECO mode switch (integration control and panel sub-assembly) operation. A
The intelligent tester display does not changes according to the ECO mode switch (integration control and panel sub-assembly) operation. B



e.

Turn the power switch off.



A

B

4.READ VALUE USING INTELLIGENT TESTER (ECO SWITCH)
4.READ VALUE USING INTELLIGENT TESTER (ECO SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Body / Air Conditioning / Data List / ECO Switch.


d.

Read the value displayed on the intelligent tester.

Body Electrical > Air Conditioner > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ECO Switch ECO mode switch (eco switch assembly) condition ON or OFF ECO mode switch (eco switch assembly) being pushed and held: ON
ECO mode switch (eco switch assembly) not pushed: OFF
-
Body Electrical > Air Conditioner > Data List
Tester Display
ECO Switch
50003 121 163

Result:
Result Proceed to
The intelligent tester display changes according to the ECO mode switch (eco switch assembly) operation. A
The intelligent tester display does not changes according to the ECO mode switch (eco switch assembly) operation. B



A

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

B

5.INSPECT ECO MODE SWITCH (ECO SWITCH ASSEMBLY)
5.INSPECT ECO MODE SWITCH (ECO SWITCH ASSEMBLY)
a.

Remove the ECO mode switch (eco switch assembly).

Click hereVehicle Interior>HEATING / AIR CONDITIONING>ECO SWITCH>COMPONENTS


b.
A259197C03
0.524,0.968 0.987,1.254 0.463,0.286 0.632,1.022 0.853,1.185 0.221,0.163 10 I49 2.256,1.752 2.375,1.915 0.119,0.163 10 E 0.248,0.222 0.43,0.386 0.182,0.163 10 *a 2.295,1.734 2.025,1.361 false 1.093,1.752 1.41,1.915 0.317,0.163 10 ECU 1.305,1.734 1.574,1.361 false
*a Component without harness connected
(ECO Mode Switch (Eco Switch Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
I49-9 (ECU) - I49-6 (E) ECO mode switch (eco switch assembly) being pushed and held Below 1 Ω
ECO mode switch (eco switch assembly) not pushed 10 kΩ or higher



c.

Install the ECO mode switch (eco switch assembly).

Result:
Proceed to
OK
NG




OK

6.CHECK HARNESS AND CONNECTOR (ECO MODE SWITCH (ECO SWITCH ASSEMBLY) - BODY GROUND)

NG

REPLACE ECO MODE SWITCH (ECO SWITCH ASSEMBLY)

6.CHECK HARNESS AND CONNECTOR (ECO MODE SWITCH (ECO SWITCH ASSEMBLY) - BODY GROUND)
a.

Disconnect connector I49 from the ECO mode switch (eco switch assembly).


b.
A259198C02
0.535,1.026 0.998,1.311 0.463,0.286 0.643,1.079 0.873,1.242 0.23,0.163 10 I49 1.018,1.809 1.138,1.973 0.119,0.163 10 E 0.345,0.245 0.527,0.408 0.182,0.163 10 *a 1.104,1.787 1.402,1.34 false
*a Front view of wire harness connector
(to ECO Mode Switch (Eco Switch Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
I49-6 (E) - Body ground Always Below 1 Ω



c.

Connect the ECO mode switch (eco switch assembly) connector.

Result:
Proceed to
OK
NG




OK

7.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - ECO MODE SWITCH (ECO SWITCH ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - ECO MODE SWITCH (ECO SWITCH ASSEMBLY))
a.

Disconnect connector I77 from the air conditioning amplifier assembly.


b.

Disconnect connector I49 from the ECO mode switch (eco switch assembly).


c.
A259933C03
0.628,3.314 1.091,3.599 0.463,0.286 0.753,3.367 0.968,3.53 0.214,0.163 10 I49 1.951,4.132 2.271,4.295 0.321,0.163 10 ECU 0.352,2.568 0.534,2.731 0.182,0.163 10 *b 0.1,0.035 0.282,0.199 0.182,0.163 10 *a 2.114,4.109 1.879,3.662 false 0.955,1.509 1.418,1.794 0.463,0.286 1.063,1.562 1.277,1.725 0.214,0.163 10 I77 1.424,2.141 1.837,2.304 0.413,0.163 10 ECOS 1.699,2.118 1.871,1.671 false
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)
*b Front view of wire harness connector
(to ECO Mode Switch (Eco Switch Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I49-9 (ECU) - I77-4 (ECOS) Always Below 1 Ω
I49-9 (ECU) or I77-4 (ECOS) - Body ground Always 10 kΩ or higher



d.

Connect the ECO mode switch (eco switch assembly) connector.


e.

Connect the air conditioning amplifier assembly connector.

Result:
Proceed to
OK
NG




OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR