Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › from 2015.04
RM2040EQ _56 Audio / Visual / Telematics _014718 PARK ASSIST / MONITORING _0075026 BLIND SPOT MONITOR SYSTEM D

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  DIAGNOSIS SYSTEM  


DESCRIPTION


a.

Blind spot monitor data and the Diagnostic Trouble Codes (DTCs) can be read from the Data Link Connector 3 (DLC3) of the vehicle. When the system seems to be malfunctioning, use the GTS to check for malfunctions and perform repairs.




DIAGNOSIS FUNCTION


a.

The blind spot monitor system displays an error message on the multi-information display to inform the driver that the system is unavailable either temporarily, or unavailable due to a malfunction.

·

When the system is unavailable temporarily: Multi-information display displays "Blind Spot Monitor Not Available".

·

When the system is unavailable due to malfunction: Multi-information display displays "Check Blind Spot Monitor System".




ABNORMALITY HISTORY


HINT:

The abnormality history for a blind spot monitor sensor can be displayed or cleared.


a.

Check abnormality history

i.

Connect the GTS to the DLC3.


ii.

Turn the power switch on (IG).


iii.

Turn the GTS on.


iv.

Turn the blind spot monitor main switch (warning canceling switch assembly) on.


v.

Enter the following menus: Body / Blind spot monitor Master or Blind spot monitor Slave / Utility / BSM Master Abnormal History or BSM Slave Abnormal History

Body Electrical > Blind Spot Monitor Master > Utility
Tester Display
BSM Master Abnormal History
50005 313 4241
Body Electrical > Blind Spot Monitor Slave > Utility
Tester Display
BSM Slave Abnormal History
50005 314 4242

vi.

Check the results displayed for the abnormality history check.

HINT:
·

If "Yes" is displayed, check the suspected area column for each item.

·

Abnormality history is stored only for the blind spot monitor sensor for which an abnormality has been detected.

·

If "No" is displayed, proceed to the next suspected area shown in Problem Symptoms Table.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>PROBLEM SYMPTOMS TABLE



Abnormality History Table
Tester Display Item Explanation Suspected Area
History of Module Blockage History of blind spot monitor sensor detection problems due to snow, rain, etc. on the bumper
·

Check if a bumper compatible with the blind spot monitor (such as an original equipment bumper) is installed

·

Check if any foreign objects are attached to the bumper

·

Check if any foreign objects are present between the bumper and sensors


History of Low Voltage History of low supply battery voltage from battery to the blind spot monitor sensor Power Source Circuit
Click here(Click here)
History of High Voltage History of high supply battery voltage from battery to the blind spot monitor sensor
History of Low Temperature History of low temperature for the blind spot monitor sensor Check the outside temperature
History of High Temperature History of high temperature for the blind spot monitor sensor



b.

Clearing abnormality history

i.

Connect the GTS to the DLC3.


ii.

Turn the power switch on (IG).


iii.

Turn the GTS on.


iv.

Turn the blind spot monitor main switch (warning canceling switch assembly) on.


v.

Enter the following menus: Body / Blind spot monitor Master or Blind spot monitor Slave / Utility / BSM Master Abnormal History or BSM Slave Abnormal History

Body Electrical > Blind Spot Monitor Master > Utility
Tester Display
BSM Master Abnormal History
50005 313 4241
Body Electrical > Blind Spot Monitor Slave > Utility
Tester Display
BSM Slave Abnormal History
50005 314 4242

vi.

Clear the BSM Master Abnormal History and/or BSM Slave Abnormal History.