Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › from 2015.04
RM2040EQ _56 Audio / Visual / Telematics _014718 PARK ASSIST / MONITORING _0075026 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1ABD  Short to +B in Buzzer  C1ABE  Short to GND or Open in Buzzer  


DESCRIPTION

·

DTC C1ABD is stored when the blind spot monitor sensor LH detects a +B short in the RCTA buzzer (blind spot monitor buzzer) circuit.

·

DTC C1ABE is stored when the blind spot monitor sensor LH detects a ground short or open in the RCTA buzzer (blind spot monitor buzzer) circuit.


DTC No. Detection Item DTC Detection Condition Trouble Area
C1ABD Short to +B in Buzzer
Both of the following conditions are met:
·

The blind spot monitor main switch (warning canceling switch assembly) is on

·

The blind spot monitor sensor is not sending voltage to the buzzer but the buzzer receives voltage above a specified level for a specified period of time


·

Blind spot monitor sensor LH

·

RCTA buzzer (blind spot monitor buzzer)

·

Wire harness or connector


C1ABE Short to GND or Open in Buzzer
Both of the following conditions are met:
·

The blind spot monitor main switch (warning canceling switch assembly) is on

·

The current flowing to the buzzer is below a specified value when buzzer operation voltage is being sent to the buzzer


·

Blind spot monitor sensor LH

·

RCTA buzzer (blind spot monitor buzzer)

·

Wire harness or connector



WIRING DIAGRAM

E254403E34
0.167,1.021 1.573,1.219 1.406,0.198 10 false from IG1 NO. 3 Relay 3.521,1.021 3.813,1.219 0.292,0.198 10 false BZP 3.177,1.313 3.521,1.51 0.344,0.198 10 false N43 3.177,1.479 5.115,1.813 1.938,0.333 10 false RCTA Buzzer (Blind Spot Monitor Buzzer) 5.615,1.927 5.906,2.125 0.292,0.198 10 false T21 5.615,2.083 6.813,2.448 1.198,0.365 10 false Blind Spot Monitor Sensor LH 4.344,1.021 4.677,1.219 0.333,0.198 10 false BZN 3.333,0.906 3.479,1.083 0.146,0.177 10 false 1 5.646,1.021 5.979,1.219 0.333,0.198 10 false BUZ 5.479,0.917 5.625,1.094 0.146,0.177 10 false 3 4.698,0.917 4.844,1.094 0.146,0.177 10 false 2 2,1.188 3.021,1.385 1.021,0.198 10 false ECU-IG1 NO. 3

CAUTION / NOTICE / HINT

NOTICE:
·

When checking for DTCs, make sure that the blind spot main switch (warning canceling switch assembly) is on.

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Slave > Clear DTCs
50002 314

b.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (RCTA BUZZER - BATTERY AND BLIND SPOT MONITOR SENSOR LH)
2.CHECK HARNESS AND CONNECTOR (RCTA BUZZER - BATTERY AND BLIND SPOT MONITOR SENSOR LH)
a.

Disconnect the N43 RCTA buzzer (blind spot monitor buzzer) connector.


b.

Disconnect the T21 blind spot monitor sensor LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N43-2 (BZN) - T21-3 (BUZ) Always Below 1 Ω
N43-2 (BZN) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
N43-1 (BZP) - Body ground Power switch on (IG) 11 to 14 V
N43-1 (BZP) - Body ground Power switch off Below 1 V



Result:
Proceed to
OK
NG



OK

3.REPLACE RCTA BUZZER (BLIND SPOT MONITOR BUZZER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE RCTA BUZZER (BLIND SPOT MONITOR BUZZER)
a.

Replace the RCTA buzzer (blind spot monitor buzzer).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>REAR CROSS TRAFFIC ALERT BUZZER>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK DTC
4.CHECK DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Slave > Clear DTCs
50002 314

b.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG