Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › from 2015.04
RM2040EQ _56 Audio / Visual / Telematics _014718 PARK ASSIST / MONITORING _0075026 BLIND SPOT MONITOR SYSTEM Y

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use the following procedure to troubleshoot the blind spot monitor system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
Result:
Proceed to
NEXT



NEXT

3.INSPECT AUXILIARY BATTERY VOLTAGE
3.INSPECT AUXILIARY BATTERY VOLTAGE
a.

Measure the auxiliary battery voltage with the power switch off.

Standard Voltage:

11 to 14 V


If the voltage is below 11 V, replace or recharge the auxiliary battery before proceeding to the next step.


Result:
Proceed to
NEXT



NEXT

4.CHECK CAN COMMUNICATION SYSTEM*
4.CHECK CAN COMMUNICATION SYSTEM*
a.

Use the GTS to check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
CAN communication system DTC is not output. A
CAN communication system DTC is output. B



A

5.CHECK FOR DTC AND FREEZE FRAME DATA*

B

5.CHECK FOR DTC AND FREEZE FRAME DATA*
a.

Refer to DTC Check / Clear for the blind spot monitor system.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Master > Trouble Codes
50001 313
Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314

b.

Record or print DTCs and freeze frame data, if necessary.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>FREEZE FRAME DATA


Result:
Result Proceed to
DTCs are output. A
DTCs are not output. B



A

6.DTC CLEAR*

B

13.PROBLEM SYMPTOMS TABLE
6.DTC CLEAR*
a.

Refer to DTC Check/Clear for the blind spot monitor system.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Master > Clear DTCs
50002 313
Body Electrical > Blind Spot Monitor Slave > Clear DTCs
50002 314
HINT:

The current DTCs may not indicate actual malfunctions depending on the vehicle operating conditions.



Result:
Proceed to
NEXT



NEXT

7.RECHECK FOR DTC*
7.RECHECK FOR DTC*
a.

Refer to DTC Check/Clear for the blind spot monitor system.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Master > Trouble Codes
50001 313
Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314

Result:
Result Proceed to
DTCs are output. A
DTCs are not output. B


HINT:
·

Even if the malfunction symptom is not confirmed, check for DTCs. This is because the system stores history DTCs.

·

Check the DTC and inspect the area that the code indicates.




A

8.DIAGNOSTIC TROUBLE CODE CHART

B

13.PROBLEM SYMPTOMS TABLE
8.DIAGNOSTIC TROUBLE CODE CHART

Result:
Proceed to
NEXT



NEXT

9.CIRCUIT INSPECTION
9.CIRCUIT INSPECTION
Result:
Proceed to
NEXT



NEXT

10.ADJUST, REPAIR OR REPLACE
10.ADJUST, REPAIR OR REPLACE
Result:
Proceed to
NEXT



NEXT

11.PERFORM BEAM AXIS INSPECTION*
11.PERFORM BEAM AXIS INSPECTION*
a.

Perform the blind spot monitor beam axis inspection.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>OPERATION CHECK

Body Electrical > Blind Spot Monitor Master > Utility
Tester Display
BSM Master Beam Axis Inspection
50005 313 4202
Body Electrical > Blind Spot Monitor Slave > Utility
Tester Display
BSM Slave Beam Axis Inspection
50005 314 4203

Result:
Proceed to
NEXT



NEXT

12.PERFORM CONFIRMATION TEST
12.PERFORM CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END

13.PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault is not listed in Problem Symptoms Table. A
Fault is listed in Problem Symptoms Table. B


HINT:

If the symptom does not recur and no DTC is output, attempt to reproduce the symptoms.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



A

14.PERFORM TROUBLESHOOTING BASED ON MALFUNCTION SYMPTOM*

B

9.CIRCUIT INSPECTION
14.PERFORM TROUBLESHOOTING BASED ON MALFUNCTION SYMPTOM*

NEXT

9.CIRCUIT INSPECTION