Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY › from 2015.04
RM2040EQ _55 Steering _014714 STEERING COLUMN _0075002 STEERING COLUMN ASSEMBLY A

STEERING COLUMN  STEERING COLUMN ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 45220 1.INSTALL STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C243095C03
2.656,1.469 2.74,1.813 2.74,1.813 2.76,1.458 false 2.656,1.781 2.906,2.042 0.25,0.26 10 false *a
*a Matchmark


Install the steering intermediate shaft assembly to the steering column assembly.

NOTICE:

Align the matchmarks on the steering intermediate shaft assembly and the steering column assembly.



b.

Install the bolt.

Torque:
35 N*m (360 kgf*cm, 26 ft.*lbf)


Hide 2.INSTALL STEERING POST ASSEMBLY

a.

Install the steering post assembly with the 4 nuts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


b.

Install the ground wire with the bolt.

Torque:
8.4 N*m (85 kgf*cm, 74 in.*lbf)


c.

Engage the clamp.


d.

Connect the 2 connectors.


e.

Connect the connectors and engage the wire harness clamps to the steering post assembly.


Hide 87201B 3.INSTALL NO. 2 AIR DUCT SUB-ASSEMBLY

a.

Engage the 2 claws to install the No. 2 air duct sub-assembly.


b.

Install the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 45220 4.CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C243088C03
1.802,0.906 2.375,1.208 2.375,1.208 1.813,1 false 2.365,1.104 2.635,1.365 0.271,0.26 10 false *a
*a Matchmark


Connect the steering intermediate shaft assembly to the steering link assembly.

NOTICE:

Align the matchmarks on the steering intermediate shaft assembly and the steering link assembly.



b.

Install the bolt.

Torque:
35 N*m (360 kgf*cm, 26 ft.*lbf)


c.
C243085

Tighten the clamp.


Hide 5.INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

NOTICE:
·

Do not replace the spiral cable with sensor sub-assembly with the auxiliary battery connected and the power switch on (IG).

·

Do not rotate the spiral cable with sensor sub-assembly without the steering wheel with the auxiliary battery connected and the power switch on (IG).

·

Ensure that the steering wheel is installed and aligned straight when inspecting the steering sensor.



a.

Engage the 3 claws to install the turn signal switch assembly with spiral cable sub-assembly to the steering post assembly.


b.

Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.


Hide 45286B 6.INSTALL UPPER STEERING COLUMN COVER

a.

Engage the 2 claws to install the upper steering column cover.


b.

Engage the 4 clips and 2 guides to the upper steering column cover.


Hide 45287 7.INSTALL LOWER STEERING COLUMN COVER

a.
C243079

Engage the 2 claws to install the lower steering column cover.


b.
C243078

Install the 2 screws.

Torque:
2.0 N*m (20 kgf*cm, 18 in.*lbf)


c.
C243080

Engage the claw.


Hide 73900 8.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 9.TURN FRONT WHEELS TO FACE STRAIGHT AHEAD

Hide 10.INSPECT AND ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

Hide 45100 11.INSTALL STEERING WHEEL ASSEMBLY

Hide 12.INSPECT STEERING WHEEL CENTER POINT

Hide 45130 13.INSTALL HORN BUTTON ASSEMBLY

Hide 14.INSTALL FRONT WHEEL

Torque:
103 N*m (1049 kgf*cm, 76 ft.*lbf)