Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2016.05
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074885 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A3F-243  Drive Motor "A" Position Sensor Circuit  P0A40-500  Drive Motor "A" Position Sensor Circuit Range / Performance  P0A41-245  Drive Motor "A" Position Sensor Circuit Low  


DESCRIPTION

A resolver is a sensor that is used to detect the position of the magnetic poles the rotor of a motor generator. Knowing the position of the poles is indispensable for ensuring precise control of MG2 and MG1.

Each resolver contains a stator that has an excitation coil and 2 detection coils (S, C). The gap between the stator and rotor changes as the rotor turns because the rotor is oval shaped. An alternating current with a predetermined frequency flows through the excitation coil, and detection coils S and C output alternating currents in accordance with the sensor rotor position.

The MG ECU located in the inverter with converter assembly detects the absolute position of the rotor according to the phases of detection coils S and C and the heights of their waveforms. Furthermore, the CPU calculates the amount of change in the position within a predetermined length of time, in order to use the resolver as a speed sensor.

The MG ECU monitors signals output from the motor resolver and detects malfunctions.

HINT:

The term "drive motor A" indicates MG2.


A221242E01
1.317,3.385 1.508,3.638 0.191,0.253 10 -S 1.726,2.135 1.916,2.388 0.191,0.253 10 -S 0.855,2.602 1.046,2.855 0.191,0.253 10 +S 2.16,2.981 2.351,3.146 0.191,0.165 10 +S 1.179,2.177 1.363,2.389 0.184,0.211 10 -C 1.838,3.401 2.021,3.612 0.184,0.211 10 -C 0.843,3.13 1.054,3.342 0.211,0.211 10 +C 2.118,2.486 2.329,2.697 0.211,0.211 10 +C 1.416,3.164 0.773,4.461 false 2.26,3.586 1.796,4.765 false 0.539,4.48 1.010,4.710 0.471,0.230 10 Rotor 1.329,4.825 2.309,5.065 0.980,0.239 10 Excitation Coil 6.015,0.314 6.995,0.553 0.980,0.239 10 Excitation Coil 5.966,2.03 7.120,2.270 1.154,0.239 10 Detection Coil S 5.971,3.501 7.087,3.741 1.117,0.239 10 Detection Coil C 4.553,2.019 5.654,2.265 1.100,0.246 10 Virtual Waveform 4.56,3.462 5.661,3.708 1.100,0.246 10 Virtual Waveform 4.514,2.098 4.378,2.343 false 4.532,3.548 3.966,4.107 false

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0A3F-243 Drive Motor "A" Position Sensor Circuit Interphase short in the motor resolver circuit
·

Inverter with converter assembly

·

Hybrid vehicle transaxle assembly

·

Wire harness or connector


Comes on Master Warning Light:
Comes on
P0A40-500 Drive Motor "A" Position Sensor Circuit Range / Performance Motor resolver output is out of the normal range
·

Inverter with converter assembly

·

Hybrid vehicle transaxle assembly

·

Wire harness or connector


Comes on Master Warning Light:
Comes on
P0A41-245 Drive Motor "A" Position Sensor Circuit Low Open or short in the motor resolver circuit
·

Inverter with converter assembly

·

Hybrid vehicle transaxle assembly

·

Wire harness or connector


Comes on Master Warning Light:
Comes on

WIRING DIAGRAM

Refer to the wiring diagram for DTC P1CAC-200 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P1CAC-200).

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Check for output DTCs again after the repair has been completed. If P0A78-286 or P0A7A-324 is output, replace the inverter with converter assembly.



HINT:

If the problem symptom cannot be reproduced, performing a road test on a road on which the vehicle tends to vibrate will make it easier to reproduce the symptom.


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

OK

2.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - GENERATOR RESOLVER)

NG

CONNECT SECURELY

2.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - GENERATOR RESOLVER)

OK

3.CHECK GENERATOR RESOLVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK GENERATOR RESOLVER

OK

4.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - MOTOR RESOLVER)

NG

8.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR)
4.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - MOTOR RESOLVER)

OK

5.CHECK MOTOR RESOLVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK MOTOR RESOLVER

OK

6.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR)

NG

10.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)
6.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR)

OK

7.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)

NG

CONNECT SECURELY

7.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)

OK

REPLACE INVERTER WITH CONVERTER ASSEMBLY

NG

CONNECT SECURELY

8.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR)

OK

9.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - GENERATOR RESOLVER)

NG

CONNECT SECURELY

9.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - GENERATOR RESOLVER)

OK

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)

OK

11.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - MOTOR RESOLVER)

NG

CONNECT SECURELY

11.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - MOTOR RESOLVER)

OK

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR