Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2016.05
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074885 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0BEA-290  Drive Motor "A" Phase V Current Sensor Circuit Range / Performance  P0BEE-298  Drive Motor "A" Phase W Current Sensor Circuit Range / Performance  P1C3C-294  Drive Motor "A" Phase V Current Sensor Correlation  P1C3D-302  Drive Motor "A" Phase W Current Sensor Correlation  P1C4A-288  Drive Motor "A" Phase V Current Sensor Sub Circuit Range / Performance  P1C4F-296  Drive Motor "A" Phase W Current Sensor Sub Circuit Range / Performance  P1C6D-501  Drive Motor "A" Phase V Current Sensor Offset Range / Performance  P1C6E-502  Drive Motor "A" Phase W Current Sensor Offset Range / Performance  


DESCRIPTION

The MG ECU located in the inverter with converter assembly monitors the motor inverter current sensors. DTCs P0BEA-290, P0BEE-298, P1C3C-294, P1C3D-302, P1C4A-288, P1C4F-296, P1C6D-501 or P1C6E-502 indicate malfunctions in current sensors, and they do not indicate malfunctions in the high-voltage system.

HINT:

The term "drive motor A" indicates MG2.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0BEA-290 Drive Motor "A" Phase V Current Sensor Circuit Range / Performance Malfunction in motor inverter current sensor (phase V main sensor) Inverter with converter assembly Comes on Master Warning Light:
Comes on
P0BEE-298 Drive Motor "A" Phase W Current Sensor Circuit Range / Performance Malfunction in motor inverter current sensor (phase W main sensor) Inverter with converter assembly Comes on Master Warning Light:
Comes on
P1C3C-294 Drive Motor "A" Phase V Current Sensor Correlation Malfunction in motor inverter current sensor (performance problem or open phase V) Inverter with converter assembly Comes on Master Warning Light:
Comes on
P1C3D-302 Drive Motor "A" Phase W Current Sensor Correlation Malfunction in motor inverter current sensor (performance problem or open phase W) Inverter with converter assembly Comes on Master Warning Light:
Comes on
P1C4A-288 Drive Motor "A" Phase V Current Sensor Sub Circuit Range / Performance Malfunction in motor inverter current sensor (phase V sub sensor) Inverter with converter assembly Comes on Master Warning Light:
Comes on
P1C4F-296 Drive Motor "A" Phase W Current Sensor Sub Circuit Range / Performance Malfunction in motor inverter current sensor (phase W sub sensor) Inverter with converter assembly Comes on Master Warning Light:
Comes on
P1C6D-501 Drive Motor "A" Phase V Current Sensor Offset Range / Performance Malfunction in motor inverter current sensor (phase V main and sub sensors offset) Inverter with converter assembly Comes on Master Warning Light:
Comes on
P1C6E-502 Drive Motor "A" Phase W Current Sensor Offset Range / Performance Malfunction in motor inverter current sensor (phase W main and sub sensors offset) Inverter with converter assembly Comes on Master Warning Light:
Comes on

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.

Powertrain > Hybrid Control > Trouble Codes
50001 236

d.

Check if DTCs are output.

Result:
Result Proceed to
Only DTC P0BEA-290, P0BEE-298, P1C3C-294, P1C3D-302, P1C4A-288, P1C4F-296, P1C6D-501 or P1C6E-502 are output or any DTCs other than P0A78-202 is also output. A
P0A78-202 is output. B



e.

Turn the power switch off.



A

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

B

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

OK

REPLACE INVERTER WITH CONVERTER ASSEMBLY

NG

CONNECT SECURELY