Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2016.05
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074885 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A7A-203  Generator Inverter Performance  


DESCRIPTION

For a description of the inverter (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0D2F-266).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0A7A-203 Generator Inverter Performance Malfunction (short circuit) in the generator inverter inside the inverter with converter assembly
·

Inverter with converter assembly

·

Hybrid vehicle transaxle assembly


Comes on Master Warning Light:
Comes on

WIRING DIAGRAM

Refer to the wiring diagram for DTC P0AA6-526 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA6-526).

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

DTC P0A7A-203 is stored after DTCs P0A1A-517, P0A4C-518, P0A7A-122, 322, 324 and/or 325 are stored. After troubleshooting and repairing the malfunction which caused DTC P0A7A-203 to be stored, be sure to troubleshoot all the other DTCs.

·

Depending on the conditions in which the vehicle is being operated when a short circuit occurs in the inverter with converter assembly, the hybrid vehicle transaxle assembly may be affected. As this DTC is stored if a short circuit occurs in the inverter with converter assembly, it is necessary to perform a road test to check the hybrid vehicle transaxle assembly. If problems are found, replace the malfunctioning parts.

·

After completing the repair, including the repair of previously output DTCs, drive the vehicle at a speed of approximately 40 km/h (25 mph) for 1 minute and check that DTC P0A92-261 (Hybrid Generator Performance) is not output. If DTC P0A92-261 (Hybrid Generator Performance) is output, replace the hybrid vehicle transaxle assembly.



PROCEDURE

1.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG1)

OK

2.REPLACE INVERTER WITH CONVERTER ASSEMBLY

NG

4.REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY
2.REPLACE INVERTER WITH CONVERTER ASSEMBLY

NEXT

3.CHECK DTC OUTPUT (HYBRID CONTROL)
3.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Check the other DTCs that were output together with DTC P0A7A-203.

Result
DTC No. Relevant Diagnosis
P0A1A-517 Generator Control Module
P0A4C-518 Generator Position Sensor Circuit Range/Performance
P0A7A-122, 322, 324, 325 Generator Inverter Performance

NOTICE:

DTC P0A7A-203 is stored after DTCs P0A1A-517, P0A4C-518, P0A7A-122, 322, 324 and/or 325 are stored. After troubleshooting and repairing the malfunction which caused DTC P0A7A-203 to be stored, be sure to troubleshoot all the other DTCs.


Result:
Proceed to
NEXT




NEXT

4.REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

NEXT

5.REPLACE INVERTER WITH CONVERTER ASSEMBLY
5.REPLACE INVERTER WITH CONVERTER ASSEMBLY

NEXT

6.CHECK DTC OUTPUT (HYBRID CONTROL)
6.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Check the other DTCs that were output together with DTC P0A7A-203.

Result
DTC No. Relevant Diagnosis
P0A1A-517 Generator Control Module
P0A4C-518 Generator Position Sensor Circuit Range/Performance
P0A7A-122, 322, 324, 325 Generator Inverter Performance

NOTICE:

DTC P0A7A-203 is stored after DTCs P0A1A-517, P0A4C-518, P0A7A-122, 322, 324 and/or 325 are stored. After troubleshooting and repairing the malfunction which caused DTC P0A7A-203 to be stored, be sure to troubleshoot all the other DTCs.


Result:
Proceed to
NEXT




NEXT