Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2016.05
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074885 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P1C2D-587  Hybrid Battery Voltage / DC/DC Converter Voltage Correlation  


DESCRIPTION

For a description of the boost converter (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0CA3-442).

The MG ECU uses a voltage sensor (VL) that is built into the boost converter to detect the high voltage before it is boosted. The ECU also uses the battery smart unit to detect HV battery voltage (VB).

HINT:

Using the GTS, check the Data List of Power Resource VB and Batt Pack Current Val. If these values are not within the below range, there is a battery smart unit malfunction.


A225448E03
0.3,1.175 1.864,1.365 1.564,0.191 10 Power Resource VB (V) 3.171,2.361 4.867,2.551 1.696,0.191 10 Batt Pack Current Val (A) 1.803,0.007 6.279,0.198 4.476,0.191 10 Power Resource VB to Batt Pack Current Val (20 to 40°C (68 to 104°F))

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P1C2D-587 Hybrid Battery Voltage / DC/DC Converter Voltage Correlation Voltages from HV battery voltage (VB) sensor and boost converter voltage (VL) sensor deviate
·

Inverter with converter assembly

·

Battery smart unit


Comes on Master Warning Light:
Comes on

PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.

Powertrain > Hybrid Control > Trouble Codes
50001 236

d.

Check if DTCs are output.

Result:
Result Proceed to
P1C2D-587 only is output. Alternatively, P1C2D- 587 and any DTCs except P0B23-129, P0CA3-442 or P0E32-585 are output. A
P1C2D-587 and P0B23-129 are output. B
P1C2D-587 and P0CA3-442 are output. C
P1C2D-587 and P0E32-585 are output. D



e.

Turn the power switch off.



A

2.CLEAR DTC

B

C

REPLACE INVERTER WITH CONVERTER ASSEMBLY

D

2.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.

Powertrain > Hybrid Control > Trouble Codes
50001 236

d.

Read and record the DTCs and freeze frame data.


e.

Clear DTCs and freeze frame data.

Powertrain > Hybrid Control > Clear DTCs
50002 236

f.

Turn the power switch off.

Result:
Proceed to
NEXT




NEXT

3.CHECK DTC OUTPUT (HYBRID CONTROL)
3.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3. (*1)


b.

Turn the power switch on (READY). (*2)


c.

Enter the following menus: Powertrain / Hybrid Control / Data List. (*3)

Powertrain > Hybrid Control > Data List
Tester Display
Power Resource VB
VL-Voltage before Boosting
50003 236 656,608

d.

If both "Power Resource VB" and "VL-Voltage before Boosting" are less than 280 V, move the shift lever to D and depress both the accelerator pedal and brake pedal at the same time to raise them to 280 V or more. (*4)


e.

Move the shift lever to P. (*5)


f.

Set the air conditioning to MAX COOL and turn the headlights on. (*6)


g.

Confirm that "Batt Pack Current Val" is more than 3 A. (*7)

Powertrain > Hybrid Control > Data List
Tester Display
Batt Pack Current Val
50003 236 703

h.

Leave the vehicle for 15 seconds with the engine stopped during steps (*5) (*6) and (*7). (*8)


i.

Enter the following menus: Powertrain / Hybrid Control / DTC. (*9)

Powertrain > Hybrid Control > Trouble Codes
50001 236

j.

Check if DTCs are output. (*10)

NOTICE:

If the low HV battery charge warning light comes on, Move the shift lever to P and start the engine to charge the HV battery. After the engine stops, perform steps (*1) through (*10) again.



Result:
Result Proceed to
No DTCs are output or DTCs other than the following are output. A
P0B23-129 is output. B
P0E32-585 is output. C
P3000-388 is output. D
P3004-132 is output. E


k.

Turn the power switch off.



A

4.CHECK DTC OUTPUT (HYBRID CONTROL)

B

C

REPLACE INVERTER WITH CONVERTER ASSEMBLY

D

LEAVE VEHICLE WITH SHIFT LEVER IN P, AND CHARGE HV BATTERY BY IDLING UNTIL IDLING STOPS (PERFORM STEPS (*1) THROUGH (*10))

E

4.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Turn the power switch on (READY). (*11)


b.

Perform a road test that repeats full acceleration to 60 km/h (37 mph) and then braking to a complete stop three times. (*12)


c.

Connect the GTS to the DLC3. (*13)


d.

Enter the following menus: Powertrain / Hybrid Control / DTC. (*14)

Powertrain > Hybrid Control > Trouble Codes
50001 236

e.

Check if DTCs are output. (*15)

Result:
Result Proceed to
No DTCs are output or DTCs other than the following are output. A
P0B23-129 is output. B
P0E32-585 is output. C
P3000-388 is output. D
P3004-132 is output. E



f.

Turn the power switch off.



A

5.READ VALUE USING GTS

B

C

REPLACE INVERTER WITH CONVERTER ASSEMBLY

D

LEAVE VEHICLE WITH SHIFT LEVER IN P, AND CHARGE HV BATTERY BY IDLING UNTIL IDLING STOPS (PERFORM STEPS (*11) THROUGH (*15))

E

5.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (READY).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List.


d.

Select "Power Resource VB", "VL-Voltage before Boosting" and "VH-Voltage after Boosting" in the Data List.

Powertrain > Hybrid Control > Data List
Tester Display
Power Resource VB
VL-Voltage before Boosting
VH-Voltage after Boosting
50003 236 656,608,609

e.

If both "Power Resource VB" and VL-Voltage before Boosting are less than 280 V, move the shift lever to D and depress both the accelerator pedal and brake pedal at the same time to raise them to 280 V or more.


f.

Move the shift lever to P (the engine is off), and read the Data List when the vehicle is stationary.

Result:
Result Proceed to
Both of the following are not satisfied. A
Both of the following are satisfied:
·

Difference between "Power Resource VB" and "VH-Voltage after Boosting" is less than 5V.

·

Difference between "VL-Voltage before Boosting" and "VH-Voltage after Boosting" is more than 30 V.


B
Both of the following are satisfied:
·

Difference between "VH-Voltage after Boosting" and "VL-Voltage before Boosting" is more than 5 V.

·

Difference between "Power Resource VB" and "VH-Voltage after Boosting" is less than 15 V.


C



g.

Turn the power switch off.



A

6.CHECK FREEZE FRAME DATA (HYBRID CONTROL)

B

REPLACE INVERTER WITH CONVERTER ASSEMBLY

C

6.CHECK FREEZE FRAME DATA (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.

Powertrain > Hybrid Control > Trouble Codes
50001 236

d.

Read the freeze frame data of DTC P1C2D-587.

Result:
Result Proceed to
Both of the following are satisfied or both of the following are not satisfied. A
"Power Resource VB" is less than 190 V or more than 340 V. B
"VL-Voltage before Boosting" is less than 190 V or more than 340 V. C



e.

Turn the power switch off.



A

7.CHECK FREEZE FRAME DATA (HYBRID CONTROL)

B

C

REPLACE INVERTER WITH CONVERTER ASSEMBLY

7.CHECK FREEZE FRAME DATA (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.

Powertrain > Hybrid Control > Trouble Codes
50001 236

d.

Read the freeze frame data of DTC P1C2D-587.

HINT:

In the freeze frame data, read the "Power Resource VB" and all of the "Battery Block Vol".


Result:
Result Proceed to
Others (Freeze frame data is not stored). A
Both of the following are satisfied:
·

Sum of all "Battery Block Vol" is more than ("Power Resource VB" - 45 V)

·

Sum of all "Battery Block Vol" is less than ("Power Resource VB" + 30 V)


B
Neither A nor B is satisfied. C



e.

Turn the power switch off.



A

8.READ VALUE USING GTS

B

REPLACE INVERTER WITH CONVERTER ASSEMBLY

C

8.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (READY).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List.

Powertrain > Hybrid Control > Data List
Tester Display
Power Resource VB
VL-Voltage before Boosting
50003 236 656,608

d.

If both "Battery Block Vol" and "VL-Voltage before Boosting" are less than 280 V, move the shift lever to D and depress both the accelerator pedal and brake pedal at the same time to raise them to 280 V or more.


e.

Move the shift lever to P (the engine is off), and read the "Power Resource VB" and all of the "Battery Block Vol", when the vehicle is stationary.

Result:
Result Proceed to
Both of the following are satisfied:
·

Sum of all "Battery Block Vol" is more than ("Power Resource VB" -45 V)

·

Sum of all "Battery Block Vol" is less than ("Power Resource VB" +30 V)


A
The preceding condition is not satisfied. B



f.

Turn the power switch off.



A

REPLACE INVERTER WITH CONVERTER ASSEMBLY

B