Home › Engine / Hybrid System › 2AR-FXE ENGINE CONTROL › SFI SYSTEM (w/o EGR System)

DTC    P0137    Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2)

for Preparation Click here


DESCRIPTION

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a TWC (Three-Way Catalytic Converter) is used. For the most efficient use of the TWC, the air fuel ratio must be precisely controlled so that it is always close to the stoichiometric air fuel level. For the purpose of helping the ECM to deliver accurate air fuel ratio control, a heated oxygen sensor is used.
The heated oxygen sensor is located behind the TWC, and detects the oxygen concentration in the exhaust gas. Since the sensor is integrated with the heater that heats the sensing portion, it is possible to detect the oxygen concentration even when the intake air volume is low (the exhaust gas temperature is low).
When the air fuel ratio becomes lean, the oxygen concentration in the exhaust gas is high. The heated oxygen sensor informs the ECM that the post-TWC air fuel ratio is lean (low voltage, i.e. less than 0.45 V).
Conversely, when the air fuel ratio is richer than the stoichiometric air fuel level, the oxygen concentration in the exhaust gas is low . The heated oxygen sensor informs the ECM that the post-TWC air fuel ratio is rich (high voltage, i.e. more than 0.45 V). The heated oxygen sensor has the property of changing its output voltage drastically when the air fuel ratio is close to the stoichiometric level.
The ECM uses the supplementary information from the heated oxygen sensor to determine whether the air fuel ratio after the TWC is rich or lean, and adjusts the fuel injection duration accordingly. Thus, if the heated oxygen sensor is working improperly due to internal malfunctions, the ECM is unable to compensate for deviations in the primary air fuel ratio control.

A254107E01


DTC No.
DTC Detection Condition
Trouble Area
P0137
  1. Low voltage (open):
    During active air fuel ratio control, the following conditions (a) and (b) are met for a certain period of time (2 trip detection logic):
    1. (a) Heated oxygen sensor voltage output is less than 0.21 V.
    1. (b) Target air fuel ratio is rich.
  1. Heated oxygen sensor (sensor 2 ) circuit
  2. Heated oxygen sensor (sensor 2)
  3. Air fuel ratio sensor (sensor 1)
  4. Gas leak from exhaust system

MONITOR DESCRIPTION


Active Air fuel Ratio Control
The ECM usually performs air fuel ratio feedback control so that the air fuel ratio sensor output indicates a near stoichiometric air fuel level. This vehicle includes active air fuel ratio control in addition to regular air fuel ratio control. The ECM performs active air fuel ratio control to detect any deterioration in the Three-Way Catalytic Converter (TWC) and heated oxygen sensor malfunctions (refer to the diagram below).
Active air fuel ratio control is performed for approximately 30 seconds while driving with a warm engine. During active air fuel ratio control, the air fuel ratio is forcibly regulated to become lean or rich by the ECM. If the ECM detects a malfunction, a DTC is stored.

Open in Heated Oxygen Sensor Circuit
During active air fuel ratio control, the ECM calculates the Oxygen Storage Capacity (OSC)* of the Three-way Catalytic Converter (TWC) by forcibly regulating the air fuel ratio to become rich or lean. If the heated oxygen sensor has an open or short circuit, or the voltage output of the sensor noticeably decreases, the OSC indicated an extraordinarily high value. Even if the ECM attempts to continue regulating the air fuel ratio to become rich or lean, the heated oxygen sensor output does not change.
While performing active air fuel ratio control, when the target air fuel ratio is rich and the heated oxygen sensor voltage output is less than 0.21 V (lean), the ECM interprets this as an abnormally low sensor output voltage and stores DTC P0137.
*: The TWC has the capability to store oxygen. The OSC and the emissions purification capacity of the TWC are mutually related. The ECM determines whether the catalyst has deteriorated based on the calculated OSC value.

A234468E26


MONITOR STRATEGY


Required Sensors/Components (Main)
Heated oxygen sensor (sensor 2)
Required Sensors/Components (Related)
Crankshaft position sensor
Engine coolant temperature sensor
Mass air flow meter sub-assembly
Throttle position sensor
Air fuel ratio sensor
Frequency of Operation
Once per driving cycle

TYPICAL ENABLING CONDITIONS


Heated Oxygen Sensor Voltage Check (Low Voltage) 
Active air fuel ratio control
Executing
Active air fuel ratio control begins when all of following conditions met:
-
Auxiliary battery voltage
11 V or higher
Engine coolant temperature
75°C (167°F) or higher
Idling
Off
Engine speed
Less than 4000 rpm
Air fuel ratio sensor status
Activated
Fuel system status
Closed loop
Engine load
10% or higher, and less than 70%

TYPICAL MALFUNCTION THRESHOLDS


Heated Oxygen Sensor Voltage Check (Low Voltage) 
Both of following conditions are met
-
(a) Commanded air fuel ratio
14.4 or less
(b) Heated oxygen sensor voltage
Less than 0.21 V

CONFIRMATION DRIVING PATTERN

HINT:
  1. This confirmation driving pattern is used in the "Perform Confirmation Driving Pattern" procedure of the following diagnostic troubleshooting procedure.
  2. Performing this confirmation driving pattern will activate the heated oxygen sensor monitor (the catalyst monitor is performed simultaneously). This is very useful for verifying the completion of a repair.


A264212E03

  1. Connect the intelligent tester to the DLC3.
  2. Turn the power switch on (IG) and turn the tester on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the power switch off and wait for at least 30 seconds.
  5. Turn the power switch on (IG) and turn the tester on [A].
  6. Put the engine in inspection mode (maintenance mode) (Click here).
  7. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].
  8. With the shift lever in D, drive the vehicle at 60 to 100 km/h (37 to 62 mph) for 10 minutes or more [C].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  9. Enter the following menus: Powertrain / Engine and ECT / DTC [D].
  10. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  12. Input the DTC: P0137.
  13. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [C] and [D] again.


WIRING DIAGRAM

Refer to DTC P0037 .

INSPECTION PROCEDURE

HINT:
Malfunctioning areas can be identified by performing the Control the Injection Volume function provided in the Active Test. The Control the Injection Volume function can help to determine whether the air fuel ratio sensor, heated oxygen sensor and other potential trouble areas are malfunctioning.
The following instructions describe how to conduct the Control the Injection Volume operation using the intelligent tester.

  1. Connect the intelligent tester to the DLC3.
  2. Turn the power switch on (IG).
  3. Turn the tester on.
  4. Put the engine in inspection mode (maintenance mode) (Click here).
  5. Start the engine.
  6. Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.

    HINT:
    During charging control, the engine speed is set at idle, the engine speed does not increase when depressing the accelerator pedal. In this case, warm up the engine after charging control has completed.

  7. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume / All Data / AFS Voltage B1S1 and O2S B1S2.
  8. Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).
  9. Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2) displayed on the tester.

HINT:
  1. Change the fuel injection volume within the range of -12% to 12%. The injection volume can be changed in fine gradations.
  2. Each sensor reacts in accordance with increase and decreases in the fuel injection volume.


Tester Display (Sensor)
Injection Volume
Status
Voltage
AFS Voltage B1S1
(Air fuel ratio)
12%
Rich
Below 3.1 V
-12%
Lean
Higher than 3.4 V
O2S B1S2
(Heated oxygen)
12%
Rich
Higher than 0.55 V
-12%
Lean
Below 0.4 V

NOTICE:
The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.


Case
Air Fuel Ratio Sensor (Sensor 1) Output Voltage
Heated Oxygen Sensor (Sensor 2) Output Voltage
Main Suspected Trouble Area
1
A150787E12
A151324E08
A150787E12
A150788E06
-
2
A150787E12
A150790E01
A150787E12
A150788E06
  1. Air fuel ratio sensor
  2. Air fuel ratio sensor heater
  3. Air fuel ratio sensor circuit
3
A150787E12
A151324E08
A150787E12
A150790E01
  1. Heated oxygen sensor
  2. Heated oxygen sensor heater
  3. Heated oxygen sensor circuit
4
A150787E12
A150790E01
A150787E12
A150790E01
  1. Fuel injector assembly
  2. Fuel pressure
  3. Gas leak from exhaust system (air fuel ratio extremely rich or lean)

HINT:
  1. Following the Control the Injection Volume procedure enables technicians to check and graph the voltage outputs of both the air fuel ratio and heated oxygen sensors.
  2. To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume / All Data / AFS Voltage B1S1 and O2S B1S2; and then press the graph button on the Data List view.

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. Sensor 1 refers to the sensor closest to the engine assembly.
  2. Sensor 2 refers to the sensor farthest away from the engine assembly.
  3. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ OUTPUT DTC (DTC P0137)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    DTC P0137 is output
    A
    DTC P0137 and other DTCs are output
    B

    HINT:
    If any DTCs other than P0137 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.CHECK FOR EXHAUST GAS LEAK
  1. Check for exhaust gas leaks.

    OK:
    No gas leaks.

    HINT:
    Perform "Inspection After Repair" after repairing or replacing the exhaust system (Click here).



NG
REPAIR OR REPLACE EXHAUST GAS LEAK POINT
OK


3.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)
  1. Inspect the heated oxygen sensor (Click here).



NG
REPLACE HEATED OXYGEN SENSOR (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
  1. Disconnect the heated oxygen sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E21-1 (HT1B) - E28-24 (HT1B)
    Always
    Below 1 Ω
    E21-3 (OX1B) - E28-100 (OX1B)
    Always
    Below 1 Ω
    E21-4 (E2) - E28-132 (EX1B)
    Always
    Below 1 Ω
    E21-1 (HT1B) or E28-24 (HT1B) - Body ground
    Always
    10 kΩ or higher
    E21-3 (OX1B) or E28-100 (OX1B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.REPLACE HEATED OXYGEN SENSOR
  1. Replace the heated oxygen sensor (Click here).


NEXT


6.PERFORM CONFIRMATION DRIVING PATTERN
  1. Perform Confirmation Driving Pattern.


NEXT


7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0137)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P0137.

  1. Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the driving pattern again but increase the vehicle speed.

    Result 
    Result
    Proceed to
    ABNORMAL
    (DTC P0137 is output)
    A
    NORMAL
    (DTC is not output)
    B

    HINT:
    Perform "Inspection After Repair" after replacing the air fuel ratio sensor (Click here).



B
END
A

REPLACE AIR FUEL RATIO SENSOR (Click here)