Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM

ENGINE IMMOBILISER SYSTEM > Security Indicator Light Does not Blink

for Preparation Click here


DESCRIPTION

  1. The certification ECU (smart key ECU assembly) blinks the security indicator light when the immobiliser is set (power switch off, or driver door is opened and closed with power switch on (IG)).
  2. The certification ECU (smart key ECU assembly) receive the security indicator light signal from the main body ECU (multiplex network body ECU) via CAN communication when the theft deterrent system is arming preparation state or alarm sounding state. Then, the certification ECU (smart key ECU assembly) blinks the security indicator light.

WIRING DIAGRAM


B278947E07


INSPECTION PROCEDURE

NOTICE:
  1. Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.
  2. The engine immobiliser system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the engine immobiliser system after confirming that the communication systems are functioning properly.

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SECURITY INDICATOR LIGHT)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Entry&Start / Active Test.

  1. Perform the Active Test according to the display on the intelligent tester.

    Entry&Start (Certification ECU (Smart Key ECU Assembly)) 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Immobiliser Indicator
    Security indicator light
    OFF/ON
    -

    OK:
    The security indicator light operates normally.



NG
Go to step 3
OK


2.CHECK SECURITY INDICATOR LIGHT OPERATION
  1. When the immobiliser is set, check that the security indicator light blinks.*1

    OK:
    The security indicator light blinks normally.

  1. When the theft deterrent system is in the arming preparation state, check that the security indicator light is on (Click here).*2

    OK:
    The security indicator light is on normally.

    Result:
    Result
    Proceed to
    *1 is NG (*2 is OK)
    A
    *2 is NG (*1 is OK)
    B



B
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
A

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) 

3.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT (HEATER CONTROL SWITCH BOARD) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
  1. Disconnect the I56 security indicator light (heater control switch board) connector.

  1. Disconnect the I86 certification ECU (smart key ECU assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I86-8 (IND)- I56-1 (LP)
    Always
    Below 1 Ω
    I86-8 (IND) - Body ground
    Always
    10 kΩ or higher
    I56-6 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
  1. Reconnect the I86 certification ECU (smart key ECU assembly) connector.

  1. Measure the voltage and check the pulse according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I56-1 (LP) - I56-6 (GND)
    Power switch off → power switch on (IG)
    Pulse generation → Below 2 V



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

REPLACE SECURITY INDICATOR LIGHT (HEATER CONTROL SWITCH BOARD) (Click here)