STEERING COLUMN ASSEMBLY > INSTALLATION |
| 1. INSTALL STEERING INTERMEDIATE SHAFT ASSEMBLY |
![]() |
Install the steering intermediate shaft assembly to the steering column assembly.
| *a | Matchmark |
Install the bolt.
| 2. INSTALL STEERING POST ASSEMBLY |
Install the steering post assembly with the 4 nuts.
Install the ground wire with the bolt.
Engage the clamp.
Connect the 2 connectors.
Connect the connectors and engage the wire harness clamps to the steering post assembly.
| 3. INSTALL NO. 2 AIR DUCT SUB-ASSEMBLY (for LHD) |
Engage the clamp to install the No. 2 air duct sub-assembly.
Engage the 2 claws and guide.
Connect the connector to the footwell light.
Engage the wire harness clamp to the No. 2 air duct sub-assembly.
| 4. INSTALL NO. 2 AIR DUCT SUB-ASSEMBLY (for RHD) |
Engage the 2 claws to install the No. 2 air duct sub-assembly.
Install the bolt.
Connect the connector to the footwell light.
| 5. CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY |
![]() |
Connect the steering intermediate shaft assembly to the steering link assembly.
| *a | Matchmark |
Install the bolt.
![]() |
Tighten the clamp.
| 6. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY |
Engage the 3 claws to install the turn signal switch assembly with spiral cable sub-assembly to the steering post assembly.
Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.
| 7. INSTALL UPPER STEERING COLUMN COVER |
Engage the 2 claws to install the upper steering column cover.
Engage the 4 clips and 2 guides to the upper steering column cover.
| 8. INSTALL LOWER STEERING COLUMN COVER |
![]() |
Engage the 2 claws to install the lower steering column cover.
![]() |
Install the 2 screws.
![]() |
Engage the claw.
| 9. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY (w/o Driver Side Knee Airbag) |
| 10. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY (w/o Driver Side Knee Airbag) |
| 11. INSTALL INSTRUMENT SIDE PANEL RH (w/o Driver Side Knee Airbag) |
| 12. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH (w/o Driver Side Knee Airbag) |
| 13. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH (w/o Driver Side Knee Airbag) |
| 14. INSTALL FRONT DOOR SCUFF PLATE RH (w/o Driver Side Knee Airbag) |
| 15. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag) |
| 16. TURN FRONT WHEELS TO FACE STRAIGHT AHEAD |
| 17. INSPECT AND ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY |
Check that the power switch is off.
Check that the cable is disconnected from the negative (-) auxiliary battery terminal.
![]() |
Check if the spiral cable with sensor sub-assembly is centered.
![]() | Colored Part |
If the spiral cable with sensor sub-assembly is not centered, center it.
![]() |
While pushing on the interlock indicated in the illustration, rotate the spiral cable with sensor sub-assembly counterclockwise slowly by hand until it stops.
![]() | Interlock |
![]() |
Rotate the spiral cable with sensor sub-assembly clockwise approximately 2.5 turns to the position where the colored part shown in the illustration is visible.
![]() | Colored Part |
![]() | Interlock |
| 18. INSTALL STEERING WHEEL ASSEMBLY |
![]() |
Install the steering wheel assembly aligning the matchmarks on the steering wheel assembly and steering main shaft.
| *a | Matchmark |
Install the steering wheel assembly set nut.
Connect the connectors to the spiral cable sub-assembly.
| 19. INSPECT STEERING WHEEL CENTER POINT |
| 20. INSTALL HORN BUTTON ASSEMBLY |
| 21. INSTALL FRONT WHEEL |